Sharp DV-NC100H (serv.man6) Service Manual ▷ View online
2-3-5
H9740MA
1-D. Azimuth Alignment of Audio/
Control/ Erase Head
Purpose:
To correct the Azimuth alignment so that the Audio/
Control/Erase Head meets tape tracks properly.
Control/Erase Head meets tape tracks properly.
Symptom of Misalignment:
If the position of the Audio/Control/Erase Head is not
properly aligned, the Audio S/N Ratio or Frequency
Response will be poor.
properly aligned, the Audio S/N Ratio or Frequency
Response will be poor.
1. Connect the oscilloscope to the audio output jack on
the rear side of the deck.
2. Playback the Test Tape (9HSFL6NS8) and confirm
that the audio signal output level is 8kHz.
3. Adjust Azimuth Adj. Screw so that the output level on
the AC Voltmeter or the waveform on the oscilloscope
is at maximum. (Fig. M6)
is at maximum. (Fig. M6)
Note: Upon completion of the adjustment of Azimuth Adj.
Screw, check the X Value by pushing the CH UP or
DOWN buttons alternately, to check the symmetry of the
envelope. Check the number of pushes to ensure preset
position. The number of pushes CH UP button to achieve
1/2 level of envelope should match the number of pushes
CH DOWN button from center. If required, redo the "X
Value Alignment."
Screw, check the X Value by pushing the CH UP or
DOWN buttons alternately, to check the symmetry of the
envelope. Check the number of pushes to ensure preset
position. The number of pushes CH UP button to achieve
1/2 level of envelope should match the number of pushes
CH DOWN button from center. If required, redo the "X
Value Alignment."
1-E. Checking and Alignment of
Tape Path during reversing
Purpose:
To make sure that the tape path is well stabilized during
reversing.
reversing.
Symptom of Misalignment:
If the tape path is unstable during reversing, the tape will
be damaged.
be damaged.
Note: Do not use an Test Tape for this procedure. If the
unit is not correctly aligned, the tape may be damaged.
unit is not correctly aligned, the tape may be damaged.
1. Insert a black cassette tape into the tray and set the
unit to REV. Then confirm if the tape has been curled
up or bent at the Take-up Guide Post [4] or REV Post
[5] (Refer to Fig. M11 and M12.)
up or bent at the Take-up Guide Post [4] or REV Post
[5] (Refer to Fig. M11 and M12.)
2. When the tape has been curled up or bent, turn the
alignment screw to adjust the height of REV Post.
(Refer to Fig. M11 and M13.)
(Refer to Fig. M11 and M13.)
Take-up Guide Post [4]
REV Post [5]
Fig. M11
Take-up Guide
Post
Post
Tape
REV Post
Tape
Correct
Incorrect
Fig. M12
Fig. M13
Tape Guide
Assembly
Assembly
Alignment
Screw
Screw
2-4-1
H9740DA
DISASSEMBLY/ASSEMBLY PROCEDURES OF DECK
MECHANISM
Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to
CABINET DISASSEMBLY INSTRUCTIONS.)
CABINET DISASSEMBLY INSTRUCTIONS.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject mode;
see the positions of [44] and [45] in Fig. DM1H on page 2-4-3. When reassembling, follow the steps in reverse order.
see the positions of [44] and [45] in Fig. DM1H on page 2-4-3. When reassembling, follow the steps in reverse order.
No.
/LOC.
STEP
No.
ING
START-
PART
REMOVAL
INSTALLATION
Fig. No.
UNPLUG/DESOLDER
UNLOCK/RELEASE/
REMOVE/*UNHOOK/
CONDITION
ADJUSTMENT
[1]
[1]
Guide Holder A
T
DM3H
2(S-1)
[2]
[1]
Assembly
Cassette Holder
T
DM4H
[3]
[2]
Slider (SP)
T
DM5H
(S-1A), *(L-1)
[4]
[2]
Slider (TU)
T
DM5H
*(L-2)
[5]
[4]
Lock Lever
T
DM5H
*(L-3), *(P-1)
[6]
[2]
Cassette Plate
T
DM5H
[7]
[7]
Cylinder Assembly
T
DM1H, DM6H
Desolder, 3(S-2)
[8]
[8]
Assembly
Loading Motor
T
DM1H, DM7H
2(S-3)
Desolder, LDG Belt,
[9]
[9]
ACE Head Assembly
T
DM1H, DM7H
(S-4)
[10]
[2]
Assembly
Tape Guide Arm
T
DM1H, DM8H-1
*(P-2)
[11]
[10]
C Door Opener
T
DM1H, DM8H-1
(S-4A), *(L-4)
[12]
[11]
Pinch Arm (B)
T
DM8H-2
DM1H, DM8H-1,
*(P-3)
[13]
[12]
Assembly
Pinch Arm (A)
T
DM8H-2
DM1H, DM8H-1,
[14]
[14]
FE Head
T
DM1H, DM9H
(S-5)
[15]
[15]
Prism
T
DM1H, DM9H
(S-6)
[16]
[2]
Slider Shaft
T
DM10H
*(L-5)
[17]
[16]
C Drive Lever (SP)
T
DM10H
[18]
[16]
C Drive Lever (TU)
T
DM10H
(S-7), *(P-4)
[19]
[19]
Capstan Motor
B
DM2H, DM11H
3(S-8), Cap Belt
[20]
[20]
Clutch Assembly (HI)
B
DM2H, DM12H
(C-1)
[21]
[20]
Center Gear
B
DM12H
[22]
[22]
F Brake Assembly (HI)
B
DM2H, DM12H
*(L-6)
[23]
[22]
Worm Holder
B
DM2H, DM13H-1
(S-9), *(L-7), *(L-8)
[24]
[22]
Pulley Assembly (HI)
B
DM2H, DM13H-1
[25]
[25]
Mode Gear (LM)
B
DM2H, DM13H-1
(C-2)
[26]
[20],[25] Mode Lever (HI)
B
DM13H-2
DM2H, DM13H-1, (C-3)
[27]
[26]
[22],[23],
Cam Gear (A) (HI)
B
DM13H-2
DM2H, DM13H-1, (C-4)
Sec.Page 2-5-1
(+)Refer to Alignment
[28]
[26]
TR Gear C
B
DM2H, DM13H-1
(C-5)
2-4-2
H9740DA
No.
/LOC.
STEP
No.
ING
START-
PART
REMOVAL
INSTALLATION
Fig. No.
UNPLUG/DESOLDER
UNLOCK/RELEASE/
REMOVE/*UNHOOK/
CONDITION
ADJUSTMENT
[29]
[28]
TR Gear Spring
B
DM13H-1
[30]
[29]
TR Gear A/B
B
DM13H-1
[31]
[31]
FF Arm (HI)
B
DM1H, DM14H
[32]
[26]
Idler Assembly (HI)
B
DM1H, DM14H
*(L-9)
[33]
[26]
BT Arm
B
DM2H, DM14H
*(P-5)
[34]
[26]
Assembly
Loading Arm (SP)
B
DM2H, DM14H
Sec.Page 2-5-1
(+)Refer to Alignment
[35]
[34]
Assembly
Loading Arm (TU)
B
DM2H, DM14H
Sec.Page 2-5-1
(+)Refer to Alignment
[36]
[16],[26]
Assembly (HI)
M Brake (TU)
T
DM1H, DM15H
[37]
[2],[26]
Assembly (HI)
M Brake (SP)
T
DM1H, DM15H
*(P-6)
[38]
[37]
Assembly
Tension Lever
T
DM1H, DM15H
[39]
[38]
T Lever Holder
T
DM15H
*(L-10)
[40]
[40]
M Gear (HI)
T
DM1H, DM15H
(C-6)
[41]
[15],[40] Sensor Gear (HI)
T
DM1H, DM15H
(C-7)
[42]
[36],[40] Reel T
T
DM1H, DM15H
[43]
[38]
Reel S
T
DM1H, DM15H
[44]
[34],[38]
Preparation
Moving Guide S
T
DM1H, DM16H
(S-11), Slide Plate
[45]
[35]
Preparation
Moving Guide T
T
DM1H, DM16H
[46]
[19]
TG Post Assembly
T
DM1H, DM16H
*(L-11)
[47]
[27]
Rack Assembly
R DM17H
Sec.Page 2-5-1
(+)Refer to Alignment
[48]
[47]
F Door Opener
R DM17H
[49]
[49]
Cleaner Assembly
T
DM1H, DM6H
[50]
[49]
CL Post
T
DM6H
*(L-12)
(6)
(5)
(4)
(3)
(2)
(1)
(7)
(1): Follow steps in sequence. When reassembling, follow the steps in reverse order.
These numbers are also used as identification (location) No. of parts in the figures.
(2): Indicates the part to start disassembling with in order to disassemble the part in column (1).
(3): Name of the part
(4): Location of the part: T=Top B=Bottom R=Right L=Left
(5): Figure Number
(6): Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered.
(3): Name of the part
(4): Location of the part: T=Top B=Bottom R=Right L=Left
(5): Figure Number
(6): Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered.
P=Spring, W=Washer, C=Cut Washer, S=Screw, *=Unhook, Unlock, Release, Unplug, or Desolder
e.g., 2(L-2) = two Locking Tabs (L-2).
e.g., 2(L-2) = two Locking Tabs (L-2).
(7): Adjustment Information for Installation
(+):Refer to Deck Exploded Views for lubrication.
2-4-3
H9740DA
[14]
[13]
[11]
[10]
[12]
[12]
[7]
[49]
[8]
[32]
[43]
[41]
[40]
[31]
[42]
[45]
[44]
[46]
[9]
[36]
[15]
[38]
[37]
Fig. DM1H
Top View
[34]
[19]
[35]
[25]
[26]
[24]
[23]
[27]
[33]
[20]
[28]
[22]
Fig. DM2H
Bottom View
Click on the first or last page to see other DV-NC100H (serv.man6) service manuals if exist.