Sharp DV-HR300H (serv.man27) Service Manual / Technical Bulletin ▷ View online
DVD 2005 07 01
Date of Issue: 20
th
December 2005
Classification:
White
DVD/HHD RECORDER TECHNICAL BULLETIN
Page 4 of 4
Sharp Electronics (UK) Limited
Reference - AvW 10 07 2005 - 1
Revision - 2
White – Carry out as required
Yellow – Carry out as required and whenever the unit comes in for service
Red – Carry out on all units
9. After about 10 seconds the LCD display on the front of the unit will change to
000200.
10. After about thirty seconds the LCD display will change to 000207 (note that the
number may be different on your unit, when the number changes, the internal
update operation is complete). DO NOT turn the power off during this process.
update operation is complete). DO NOT turn the power off during this process.
11. Remove the disc from the disc tray. Do not close the disc tray.
12. Press the standby button to turn the power off.
13. When the power down cycle is complete, turn the unit back on.
14. The disc tray will close.
15. Press and hold the CH+ and REC STOP buttons together for more than two
12. Press the standby button to turn the power off.
13. When the power down cycle is complete, turn the unit back on.
14. The disc tray will close.
15. Press and hold the CH+ and REC STOP buttons together for more than two
seconds.
16. The LCD display will change to 040800.
17. Press the 9 button on the remote control.
18. After a while the LCD display will change to 0517.
19. Press the standby button to return to the standby mode.
20. Disconnect the AC cable.
17. Press the 9 button on the remote control.
18. After a while the LCD display will change to 0517.
19. Press the standby button to return to the standby mode.
20. Disconnect the AC cable.
Checking the Software Versions
1. Connect the unit to a suitable display.
2. Turn the unit on.
3. Wait until the HDD and DVD buttons have stopped flashing.
4. Press the CH+ and REC STOP buttons together for about five seconds.
5. The monitor display will change as below.
2. Turn the unit on.
3. Wait until the HDD and DVD buttons have stopped flashing.
4. Press the CH+ and REC STOP buttons together for about five seconds.
5. The monitor display will change as below.
6. To exit this menu, enter the standby mode.
In the above example the DVD writer software is verson 1.44. The flash software
version is 1.20
version is 1.20
Flash software
version
version
DVD Writer
software
version
software
version
DVD 2005 07 01
Date of Issue: 20
th
December 2005
Classification:
White
DVD/HHD RECORDER TECHNICAL BULLETIN
Page 4 of 4
Sharp Electronics (UK) Limited
Reference - AvW 10 07 2005 - 1
Revision - 2
White – Carry out as required
Yellow – Carry out as required and whenever the unit comes in for service
Red – Carry out on all units
9. After about 10 seconds the LCD display on the front of the unit will change to
000200.
10. After about thirty seconds the LCD display will change to 000207 (note that the
number may be different on your unit, when the number changes, the internal
update operation is complete). DO NOT turn the power off during this process.
update operation is complete). DO NOT turn the power off during this process.
11. Remove the disc from the disc tray. Do not close the disc tray.
12. Press the standby button to turn the power off.
13. When the power down cycle is complete, turn the unit back on.
14. The disc tray will close.
15. Press and hold the CH+ and REC STOP buttons together for more than two
12. Press the standby button to turn the power off.
13. When the power down cycle is complete, turn the unit back on.
14. The disc tray will close.
15. Press and hold the CH+ and REC STOP buttons together for more than two
seconds.
16. The LCD display will change to 040800.
17. Press the 9 button on the remote control.
18. After a while the LCD display will change to 0517.
19. Press the standby button to return to the standby mode.
20. Disconnect the AC cable.
17. Press the 9 button on the remote control.
18. After a while the LCD display will change to 0517.
19. Press the standby button to return to the standby mode.
20. Disconnect the AC cable.
Checking the Software Versions
1. Connect the unit to a suitable display.
2. Turn the unit on.
3. Wait until the HDD and DVD buttons have stopped flashing.
4. Press the CH+ and REC STOP buttons together for about five seconds.
5. The monitor display will change as below.
2. Turn the unit on.
3. Wait until the HDD and DVD buttons have stopped flashing.
4. Press the CH+ and REC STOP buttons together for about five seconds.
5. The monitor display will change as below.
6. To exit this menu, enter the standby mode.
In the above example the DVD writer software is verson 1.44. The flash software
version is 1.20
version is 1.20
Flash software
version
version
DVD Writer
software
version
software
version
DVD 2005 07 01
Date of Issue: 20
th
December 2005
Classification:
White
DVD/HHD RECORDER TECHNICAL BULLETIN
Page 4 of 4
Sharp Electronics (UK) Limited
Reference - AvW 10 07 2005 - 1
Revision - 2
White – Carry out as required
Yellow – Carry out as required and whenever the unit comes in for service
Red – Carry out on all units
9. After about 10 seconds the LCD display on the front of the unit will change to
000200.
10. After about thirty seconds the LCD display will change to 000207 (note that the
number may be different on your unit, when the number changes, the internal
update operation is complete). DO NOT turn the power off during this process.
update operation is complete). DO NOT turn the power off during this process.
11. Remove the disc from the disc tray. Do not close the disc tray.
12. Press the standby button to turn the power off.
13. When the power down cycle is complete, turn the unit back on.
14. The disc tray will close.
15. Press and hold the CH+ and REC STOP buttons together for more than two
12. Press the standby button to turn the power off.
13. When the power down cycle is complete, turn the unit back on.
14. The disc tray will close.
15. Press and hold the CH+ and REC STOP buttons together for more than two
seconds.
16. The LCD display will change to 040800.
17. Press the 9 button on the remote control.
18. After a while the LCD display will change to 0517.
19. Press the standby button to return to the standby mode.
20. Disconnect the AC cable.
17. Press the 9 button on the remote control.
18. After a while the LCD display will change to 0517.
19. Press the standby button to return to the standby mode.
20. Disconnect the AC cable.
Checking the Software Versions
1. Connect the unit to a suitable display.
2. Turn the unit on.
3. Wait until the HDD and DVD buttons have stopped flashing.
4. Press the CH+ and REC STOP buttons together for about five seconds.
5. The monitor display will change as below.
2. Turn the unit on.
3. Wait until the HDD and DVD buttons have stopped flashing.
4. Press the CH+ and REC STOP buttons together for about five seconds.
5. The monitor display will change as below.
6. To exit this menu, enter the standby mode.
In the above example the DVD writer software is verson 1.44. The flash software
version is 1.20
version is 1.20
Flash software
version
version
DVD Writer
software
version
software
version
DVD 2005 07 01
Date of Issue: 20
th
December 2005
Classification:
White
DVD/HHD RECORDER TECHNICAL BULLETIN
Page 4 of 4
Sharp Electronics (UK) Limited
Reference - AvW 10 07 2005 - 1
Revision - 2
White – Carry out as required
Yellow – Carry out as required and whenever the unit comes in for service
Red – Carry out on all units
9. After about 10 seconds the LCD display on the front of the unit will change to
000200.
10. After about thirty seconds the LCD display will change to 000207 (note that the
number may be different on your unit, when the number changes, the internal
update operation is complete). DO NOT turn the power off during this process.
update operation is complete). DO NOT turn the power off during this process.
11. Remove the disc from the disc tray. Do not close the disc tray.
12. Press the standby button to turn the power off.
13. When the power down cycle is complete, turn the unit back on.
14. The disc tray will close.
15. Press and hold the CH+ and REC STOP buttons together for more than two
12. Press the standby button to turn the power off.
13. When the power down cycle is complete, turn the unit back on.
14. The disc tray will close.
15. Press and hold the CH+ and REC STOP buttons together for more than two
seconds.
16. The LCD display will change to 040800.
17. Press the 9 button on the remote control.
18. After a while the LCD display will change to 0517.
19. Press the standby button to return to the standby mode.
20. Disconnect the AC cable.
17. Press the 9 button on the remote control.
18. After a while the LCD display will change to 0517.
19. Press the standby button to return to the standby mode.
20. Disconnect the AC cable.
Checking the Software Versions
1. Connect the unit to a suitable display.
2. Turn the unit on.
3. Wait until the HDD and DVD buttons have stopped flashing.
4. Press the CH+ and REC STOP buttons together for about five seconds.
5. The monitor display will change as below.
2. Turn the unit on.
3. Wait until the HDD and DVD buttons have stopped flashing.
4. Press the CH+ and REC STOP buttons together for about five seconds.
5. The monitor display will change as below.
6. To exit this menu, enter the standby mode.
In the above example the DVD writer software is verson 1.44. The flash software
version is 1.20
version is 1.20
Flash software
version
version
DVD Writer
software
version
software
version
Display