Sharp BD-HP35S (serv.man9) User Manual / Operation Manual ▷ View online
19
Connection
Broadband Internet Connection
Wireless connection (wireless LAN)
Insert the wireless LAN adapter (supplied) into the W-LAN/USB1 terminal on the
rear of the player.
Wireless LAN adapter
(Supplied)
PC
Wireless
router
Modem
Internet
When a wireless connection is made, it is necessary to enter the MAC address
shown on the wireless LAN adapter for the wireless router. We recommend writing
down the MAC address in this operation manual. (See page 48.)
NOTE
• When you insert or remove a wireless LAN adapter, be sure to turn the main power off
and make sure that “Quick Start” is set to “No” (See page 43).
• You must use a wireless router/access point that supports IEEE802.11 b/g/n. (n is
recommended for stable operation of the wireless network.)
• Wireless LAN, in its nature, may cause interference, depending on the usage conditions
(access point performance, distance, obstacles, interference by other radio devices,
etc.).
• Set the wireless router/access point to Infrastructure mode. Ad-hoc mode is not
supported.
• SHARP cannot guarantee that wireless LAN adapters other than the supplied adapter
will operate with this player.
• SHARP cannot guarantee that all brands’ wireless routers will operate with this player.
E
After connecting
• Perform the communication settings. (Pages 46–49)
• When enjoying BD-LIVE functions, see pages 28 and 44.
• When enjoying video on-demand services (e-Contents), see page 55.
• To play back files via the Home Network, see page 34.
• To update the software via the Internet, perform Software Update Settings.
(Pages 51–52)
20
Playback
Before Starting Playback
Loading the Batteries in the Remote
Control
1
Hold in the tab on the battery cover and pull the
cover towards the direction of the arrow.
2
Load the two “AA” size batteries (R-06 size,
UM/SUM-3). Place batteries with their terminals
corresponding to the m and n indications in
battery compartment.
3
Insert the smaller tab of the battery cover into
the opening 1, and press down on the cover
until it clicks in place 2.
WARNING
• Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater.
This can cause batteries to leak, overheat, explode or
catch fire.
It can also reduce the life or performance of batteries.
NOTE
• Do not subject the remote control unit to shock, water
or excessive humidity.
• The remote control unit may not function if the Player’s
remote sensor is in direct sunlight or any other strong
light.
• Incorrect use of batteries may cause them to leak or
burst. Read the battery warnings and use the batteries
properly.
• Do not mix old and new batteries, or mix different
brands.
• Remove the batteries if you will not use the remote
control unit for an extended period of time.
Approximate operating range of
remote control
Remote control sensor
15º
30º
30º
15º
*Approx. 7m
Remote control unit
Connecting the Power Cord
Plug the supplied AC cord into the AC IN terminal on
the rear of the Player (1). Then plug into AC outlet
(2).
NOTE
• Place the Player close to the AC outlet, and keep the
power plug within reach.
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH THE UN-INSULATED PARTS OF ANY CABLES
WHILE THE AC CORD IS CONNECTED.
• The B (On/Standby) indicator blinks while the Player is
preparing for starting up. You cannot turn the Player on
until the B (On/Standby) indicator stops blinking.
• If you are not going to use this Player for a long period
of time, be sure to remove the AC cord from the AC
outlet.
21
Playback
Before Starting Playback
Turning the Power On
2
1
4
3
1 B (Power) button
2 B (On/Standby) indicator
3 Front panel display
4 BD/DVD/CD mode indicator
Turning the power on
Press B on the remote control or on the Player to
turn on the power of the Player.
NOTE
• When you turn on this player for the first time after
purchase or when you turn on this player after you
perform “System Reset” (see page 45), the language
setting screen will be displayed, so please perform the
language setting (see step 3 of page 22).
Entering standby
Press B on the remote control or on the Player to
enter standby.
• If you press B again immediately after entering
standby, the Player may not turn on. If this happens,
wait for 10 seconds or more and then turn on the power
again.
NOTE
• When the B (On/Standby) indicator is blinking (may
take some time), the Player cannot be turned on.
Indicators on the Player
B
(On/Standby) indicator
Green on
Power on
Red on
Standby
BD/DVD/CD mode indicator
Blue on
Playing back
Blue blinks
Loading a disc/updating
About the Home screen
When turning on the player, the Home screen
appears.
Home screen
Video
Music
Picture
BD-Video
USB
Home Network
e-Contents
Settings
ENTER
EXIT
Select
Enter
Return
Exit
1
5
3
2
4
1 Main menu
2 Icon for disc inserted
3 Icon for USB memory device connected
4 Icon for LAN connection
5 Button Guide
22
Before Starting Playback
Language Setting
Changing the on-screen display
language
1
Press a/b to select “Settings”, then press d or
ENTER.
2
Press a/b to select “On Screen Language”,
then press d or ENTER.
HOME
Video
Music
Picture
Audio Video Settings
Smart Settings
AQUOS LINK
Playback Setting
On Screen Language
Communication Setup
Version
USB Memory Management
Software Update Settings
System
e-Contents
Settings
ENTER
EXIT
Select
Enter
Return
Exit
3
Press a/b to select the language you want to
display on the screen, then press
ENTER.
English
Nederlands
Česky
Deutsch
Svenska
Magyar
Français
Dansk
Slovensky
Italiano
Norsk
Slovenščina
Español
Suomi
Português
Polski
NOTE
• To select the DVD disc language, such as subtitle
language, etc., see page 26.
Operating a SHARP TV Using the
Remote Control
The Universal Remote Control may operate the
basic functions of the SHARP TV.
TV function control
• TV Power: B
• TV-AV Selector: b
• TV Volume up/down: i e/f
• TV Channel up/down:
P r/s
Turning Off the LCD Backlight and
Indications
If you feel that the indicators on the player’s front
display are too bright when watching movies, you
can turn them off except for the B (On/Standby)
indicator.
1
Press a/b to select “Settings”, then press d or
ENTER.
2
Press a/b to select “Smart Settings”, then
press d or ENTER.
3
Press a/b to select “Front Display/LED”, then
press d or ENTER.
4
Press a/b to select “On” or “Off”, then press
ENTER.
5
Press
HOME or EXIT to exit.
Click on the first or last page to see other BD-HP35S (serv.man9) service manuals if exist.