DOWNLOAD Sharp BD-HP20H Service Manual ↓ Size: 13.97 MB | Pages: 86 in PDF or view online for FREE

BD-HP20S/SA/SB/H/X/RU

3 – 5

㪨㪚㪥㪮㪄㪜㪉㪉㪎㪮㪡㪧㪱

㪍㪇㪇

㹤

㪚㪥㪉㪌㪇㪈㩷 㪚㪥㪐㪌㪇㪈

㪍㪇㪇

㪍㪇㪇

㪘

㹤

㪚㪥㪌㪍㪇㪈㩷 㪚㪥㪉㪊㪇㪈

㪙

㪨㪚㪥㪮㪄㪜㪉㪉㪏㪮㪡㪧㪱

㪚

㪨㪚㪥㪮㪄㪜㪉㪉㪐㪮㪡㪧㪱

㹤

㪪㪚㪌㪍㪇㪈㩷

㹤

㪪㪚㪌㪍㪇㪉㩷

㪚㪥㪉㪊㪇㪉

㪨㪚㪥㪮㪄㪜㪌㪎㪊㪮㪡㪧㪱

㹤

㪚㪥㪐㪇㪈㩷 㪙㪛㩷㪛㪩㪠㪭㪜

㪌㪇㪇

㪛

㪜

㹤

㪚㪥㪏㪈㪇㪉㩷 㪙㪛㩷㪛㪩㪠㪭㪜

7UGFKPVJGCDQXG
QPGRNCEG 2KP

7UGFKPVJGCDQXG
QPGRNCEGU 2KP

7UGFKPVJGCDQXG
VJTGGRNCEGU 2KP

7UGFKPVJGCDQXG
QPGRNCEGU 2KP

7UGFKPVJGCDQXG
QPGRNCEGU 2KP

㪘㪫㪘㪍㪍㩷㪚㪸㪹㫃㪼㩷㩿㪚㫆㫄㫄㪼㫉㪺㫀㪸㫃㫃㫐㩷㪸㫍㪸㫀㫃㪸㪹㫃㪼㪀

CN

㹤

㪪㪚

㩷

CN

BD-HP20S/SA/SB/H/X/RU

3 – 6

1. To replace the Main CBA, perform the items 9 - 12 of [4] Upgrading and confirm the version: it is necessary to upgrade with a disc to the latest ver-

sion if the CBA version is old.

2. When replacing the NOR Flash Memories for SIGMA (IC8503, IC8504), even if one of them is to be replaced, both types need to be replaced.

When replacing the Flash Memories, use ones with the same version.

3. The E2PROMs for SIGMA (IC7601) and (IC7602) cannot be replaced independently as a single part, because the system information needs to be

written. (The whole CBA needs to be replaced.)

4. After replacing the E2PROM for front-end software (IC2505), perform Menu - Miscellaneous Settings - Reset Settings.

1. Press [Power] button to turn the switch on, then wait till the BD_LED changes from blinking to lit.

2. Press [Tray Open/Close] button to open the Tray, put the upgrade disc on the tray and close the tray.

3. The power automatically turns off. Then it turns on again and the upgrading with the disc will start.

4. During the upgrading, the status changes from blinking DVD_LED (white) to blinking BD_LED (white) as “V-up” message keeps blinking on LCD.

5. When upgrading with the disc is completed, the Tray automatically opens.

*

If the front-end software was upgraded, BD_LED (white) will blink and stop; then DVD_LED and BD_LED will turn blue, red, etc.; the Tray will
open after the upgrading is completed and the power will turn off. (Go to step 8.)

6. When the upgrading is completed, the LCD will display as follows:

(1) Upgrading successful:”V-End” will light.

(2) Upgrading unsuccessful: “V-Err” will light.

7. Remove the disc from the Tray and press any other button of the Main Unit than [Power], then the Tray will close and the power will automatically

turn off. (Confirm the power-off by stop of the Cooling Fan.)

*

If [Power] button is pressed, the power will turn off with the Tray open.

*

If the upgrading was unsuccessful, perform the procedure again from the step 1. 

8. Press [Power] button to turn the power on, then wait till the BD_LED changes from blinking to lit.

9. Switch to [Main Diagnostic Menu] using [F4] button of the special remote control for servicing.

10.Looking at the version numbers in SIGMA Ver. and FRONT Ver., confirm that the upgrading to the desired version was completed.

11. Quit [Main Diagnostic Menu] by pressing [Green] button of the remote control.

12.Press [Power] button to turn the power off. (Confirm the power-off by stop of the cooling fan.)

BD-HP20S/SA/SB/H/X/RU

3 – 7

5VCTV

6WTPVJGRQYGTQP

1RGPVJG6TC[
RWVVJGWRITCFGFKUECPF
ENQUGVJGVTC[

6JGRQYGTCWVQOCVKECNN[
VWTPUQHH6JGPVJGRQYGT
VWTPUQPCWVQOCVKECNN[CPF
VJGWRITCFKPIUVCTVU

LCD display: "V-up"

6JG6TC[QRGPU
CWVQOCVKECNN[

7RITCFKPIEQORNGVGF

0Q

;GU

LCD display: "V-End"

LCD display: "V-Err"

4GOQXGVJGFKUECPFVWTP
VJGRQYGTQHH

4GOQXGVJGFKUECPFVWTP
VJGRQYGTQHH

6WTPVJGRQYGTQPCPF
EQPHKTOVJGXGTUKQP

'PF

4GUVCTV

7RITCFKPIUWEEGUUHWN

7RITCFKPIWPUWEEGUUHWN

BD-HP20S/SA/SB/H/X/RU

3 – 8

MEMO