DOWNLOAD Sharp XL-UR250H Service Manual ↓ Size: 4.47 MB | Pages: 55 in PDF or view online for FREE

8

XL-UR2110H

XL-UR250H

XL-UR230H

The connection lead is not included. Purchase a commercially
available lead as shown below.

 
Auto power on function (USB/AUX):
When you press any of the following buttons, the unit turns on.

VIDEO/AUX/USB button (main unit and remote control): The unit
turns on and the “USB” or “AUX” function is activated.

 /   button on the main unit: The unit turns on and playback of

the last function starts (CD,TUNER,VIDEO/AUX/USB).

Note:
To prevent noise interference, place the unit away from the
television.
 
 

Before plugging in or unplugging the headphones, reduce the
volume.
Be sure your headphones have a 3.5 mm (1/8") diameter plug and
impedance between 16  and 50 ohms. The recommended
impedance is 32 ohms.
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME control.

When using video equipment, connect the audio output to this 
unit and the video output to a television.

XL-UR2110H

XL-UR250H

XL-UR230H

When a commercially available subwoofer with a built-in amplifier is
connected to this unit, you can enjoy sound with emphasised bass.
Connect an RCA lead from a commercially available speaker with a
built-in amplifier to the SUBWOOFER PRE-OUT socket.

Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.

 

Subwoofer with a 

built-in amplifier

The clock is not set to the 
correct time.

Did a power failure occur? Reset 
the clock. (Refer page 11)

When a button is pressed, 
the unit does not respond.

Set the unit to the power stand-
by mode and then turn it back on.

If the unit still malfunctions, reset 
it. (Refer page 38)

No sound is heard.

Is the volume level set to “0”?

Are the headphones connected?

Are the speaker wires discon-
nected?

Playback does not start.

Is the disc loaded upside down?

Playback stops in the 
middle or is not performed 
properly.

Does the disc satisfy the 
standards?

Is the disc distorted or 
scratched?

Playback sounds are 
skipped, or stopped in the 
middle of a track.

Is the unit located near excessive 
vibrations?

Is the disc very dirty?

Has condensation formed inside 
the unit?

8

XL-UR2110H

XL-UR250H

XL-UR230H

Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc in the unit until normal playback is
possible (about 1 hour). Wipe off any condensation on the transmitter
with a soft cloth before operating the unit.
 

When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such problem occurs, do the following:
1

Set the unit to the stand-by mode and turn the power on again.

2

If the unit is not restored in the previous operation, unplug and
plug in the unit again, and then turn the power on.

Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
 

1

Press the ON/STAND-BY button to enter the power stand-by
mode.

2

Whilst pressing down the   1 button and the   5 button, press
the ON/STAND-BY button until “CLEAR ALL” appears.

 
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD programme.

The remote 
control does not 
operate.

Is the AC power lead of the unit plugged in?
Is the battery polarity correct?
Are the batteries dead?
Is the distance or angle incorrect?
Does the remote control sensor receive 
strong light?

The radio 
makes unusual 
noises continu-
ously.

Is the unit placed near the TV or computer?
Is the FM aerial or AM loop aerial placed 
properly? Move the aerial away from the 
AC power lead if it's located nearby.

Device cannot 
be detected.

Is there any MP3/WMA file available?
Is the device properly connected?
Is it MTP device?
Does the device contain AAC file only?

Playback does 
not start.

Is it the copyright protected WMA file?
Is it the false MP3 file?

Wrong time   
display.
Wrong file name 
display.

Is Variable Bitrate file being played back?

Is the File Name written in Chinese or 
Japanese characters?

Recording 
cannot start.

Is the USB device in write protect mode?
Is it a CD-WMA disc?
Is the device’s memory already full?

XL-UR2110H

XL-UR250H

XL-UR230H

Remove all CDs from the unit. Make sure there is no CD in the disc
tray. Then, set the unit to the power stand-by mode. Carrying the
unit with discs left inside can damage the unit.
 

Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface. Follow
the guidelines below for maximum enjoyment from your CD
collection and player.

Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
Keep your discs away from direct sunlight, heat, and excessive
moisture.
Always hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the centre, along the radius.

Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.

Do not use chemicals for cleaning (petrol, paint thinner, etc.). It
may damage the cabinet finish.
Do not apply oil to the inside of the unit. It may cause
malfunctions.