Sharp XL-DAB227NH (serv.man4) Service Manual ▷ View online
XL-DAB227NH
2 – 3
During at Step , if press << >> for more than 1 sec, it directly
goes to step .
goes to step .
To cancel: Power OFF
<<STOP>> key input.
a) Focus Balance
= FB : XX
b) Focus Gain
= FG : XX
c) Tracking Balance
= TB : XX
d) Tracking Gain
= TG : XX
e) Focus Offset
= FOFF : XX
f) Tracking Offset
= TOFF : XX
g) RFRP
= RFRP : XX
h) Focus Error
(RW Judgement)
(RW Judgement)
= RW : XX - XXXX
i) Focus Error
(Other than RW Judgement) = DA : XX - XXXX
(Other than RW Judgement) = DA : XX - XXXX
Sliding the PICKUP with << >>, << >> button can be set
in STOP mode or play mode.
in STOP mode or play mode.
STOP and return to Step 1
1
5
Note
STOP and return to Step 1
Everytime << DISPLAY >> key input
/
XL-DAB227NH
2 – 4
[3] Standard Specification Of Stereo System Error Message Display Contents
AMP abnormal detection and +B PROTECTION display
In case AMP abnormal detection or +B PROTECTION had occurred, the unit will automatically enter to stand-by
mode and Timer indicator will flashing as below.
mode and Timer indicator will flashing as below.
Example: In case of speaker abnormal
BEFORE TRANSPORTING THE UNIT
The following process need to be taken after set tapering/parts replacement.
1. Press the POWER ON/STAND-BY button to enter stand-by mode.
2. While pressing down the POWER button and the CD button, plug-in AC. The Micro Computer version number will
be displayed as "D7H10**".
3. Press the STOP button until "WAIT" --> "FINISHED" appears.
4. Unplug the AC cord and the unit is ready for transporting.
Error Contents
DISPLAY
Notes
CD
Focus Not Match/IL Time Over.
‘NO DISC’
TIMER
LED
LED
OFF
OFF
OFF
1
OFF
OFF
OFF
OFF
FRAME
(REPEAT)
FLASHING
FLASHING
NO. 2
NO. 2
ON
ON
ON
ON
NO. 1 : +B PROTECTION
NO. 2 : AMP abnormal
NO. 2 : AMP abnormal
NO
NO. 1
. 1
XL-DAB227NH
3 – 1
CHAPTER 3. MECHANICAL DESCRIPTION
[1] Disassembly
Note:
After removing the connector for the optical pickup from
the connector, wrap the conductive aluminium foil around
the front end of the connector so as to protect the optical
pickup from electrostatic damage.
the connector, wrap the conductive aluminium foil around
the front end of the connector so as to protect the optical
pickup from electrostatic damage.
Caution on disassembly
Follow the below-mentioned notes when disassembling
the unit and reassembling it, to keep it safe and ensure
excellent performance:
1) Take cassette tape and compact disc out of the unit.
2) Be sure to remove the power supply plug from the
the unit and reassembling it, to keep it safe and ensure
excellent performance:
1) Take cassette tape and compact disc out of the unit.
2) Be sure to remove the power supply plug from the
wall outlet before starting to disassemble the unit.
3) Take off nylon bands or wire holders where they
need to be removed when disassembling the unit.
After servicing the unit, be sure to rearrange the
leads where they were before disassembling.
After servicing the unit, be sure to rearrange the
leads where they were before disassembling.
4) Take sufficient care on static electricity of integrated
circuits and other circuits when servicing.
Figure 1
Figure 2
Figure 3
Side Panel
(Right)
(Right)
Side Panel
(Left)
3x12mm
(A1)x2
Rear Panel
Front Panel
Top Cabinet
3x10mm
(B1)x2
3x10mm
(C1)x1
3x10mm
(B1)x2
3x10mm
(B1)x2
3x12mm
(A1)x2
3x12mm
(A1)x2
3x10mm
(B1)x2
3x10mm
(D1)x4
3x10mm
(C1)x1
PULL
Speaker PWB
(D2)x1
(D3)x1
Hook
(C2)x1
PULL
Hook
(C2)x1
Rear Panel
CD MP3 PWB
CD Changer Unit
(C4)x2
(C3)x2
(C3)x1
Front Panel
PULL
(E4)x1
Front panel
Main PWB
Power PWB
(E3)x1
(F2)x1
(G1)x4
4x6mm
(F2)x1
(E1)x2
3x10mm
3x10mm
(F1)x2
3x10mm
3x10mm
(E2)x2
(E4)x1
Hook
PULL
1
Top Cabinet
1
2
Side Panel
(Left/Right)
(Left/Right)
1
3
CD Changer unit
2
1. Screw ............................(C1) X 2
2. Hook ..............................(C2) X 2
3. Socket ...........................(C3) X 3
4. Flat Cable ......................(C4) X 2
1. Screw ............................ (E1) X 3
2. Flat Cable ...................... (E2) X 2
3. Socket ........................... (E3) X 1
4. Hook .............................. (E4) X 2
1. Knob ...............................(J1) X 1
2. Nut ..................................(J2) X 1
3. Washer ...........................(J3) X 1
4. Screw .............................(J4) X 6
1. Screw ........................... (M1) X 1
1. Screw ............................ (P1) X 4
2. Screw ............................ (P2) X 4
1. Screw ............................(D1) X 4
2. Socket ...........................(D2) X 1
3. Flat Cable ......................(D3) X 1
1. Screw ............................ (F1) X 3
2. Socket ........................... (F2) X 2
1. Screw ............................(G1) X 4
1. Screw ............................(H1) X 2
1. Screw ............................ (K1) X 2
1. Screw ............................ (L1) X 1
1. Screw ............................ (A1) X 6
1. Screw ............................ (B1) X 8
4
Rear Panel with
2
Speaker PWB
5
Front Panel
3
6
Main PWB
3
7
Power PWB
3
8
Speaker PWB
4
9
Display PWB
5
10
USB PWB / SUB PWB
5
11
Jack PWB
5
12
Re-Flash PWB
6
14
CD Mechanism
7
8
STEP
REMOVAL
PROCEDURE
FIGURE
1. Screw ............................(N1) X 3
2. Flat Cable ......................(N2) X 2
3. Socket ...........................(N3) X 1
13
CD MP3 PWB
7
(E1)x1
3x6mm
(F1)x1
3x6mm
XL-DAB227NH
3 – 2
(P2)x4
Special
Special
CD Changer Unit
Rear Panel
(Q1) x 2
M3x10mm
(Q6) x 2
Spacer PWb
DAB PWB
(Q5) x 1
DAB Module
(Q3) x 1
Bracket,
Bracket,
DAB Support B
(Q2) x 1
Bracket,
Bracket,
DAB Support A
(Q4) x 2
M3 x 10mm
CD Mechanism
USB PWB
SUB PWB
Display PWB
Jack PWB
(K1)x2
(L1)x1
Special
Re-Flash PWB
Main Chassis
(J4)x6
(J1)x1
(J2)x1
(J3)x1
Front Panel
(P1)x2
(N2)x2
(N3)x1
Ø3x10mm
CD Changer
Unit
Unit
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Ø2.6x10mm
Ø2.6x10mm
(M1)x1
Ø3x10mm
(N1)x3
Ø3x10mm
(P1)x2
Ø3x10mm
(H1)x2
Ø3x10mm
Ø3x10mm
Speaker PWB
Rear Panel
Click on the first or last page to see other XL-DAB227NH (serv.man4) service manuals if exist.