Sharp XL-DAB227NH (serv.man4) Service Manual ▷ View online
XL-DAB227NH
6 – 51
4
C25
C1
C3
C29
C32
C31
C30
C28
R14
C27
C26
R16
C34
R20
C33
JP3
C36
C35
FB2
FB1
C39
R22
C38
R23
R21
C37
C56
C49
IC1
R34
JP4
CA3
RA4
RA5
C41
C52
C47
C46
C44
C43
R25
R24
C45
R39
CA4
R55
C71
C72
R56
R44
R43
RA44
Q8
Q3
Q5
Q4
R40
R48
R51
R46
C66
R92
R93
RA45
C62
R94
R53
C64
R54
C58
C59
IC2
C61
7
8
9
10
11
12
Figure 6-47: WIRING SIDE OF CD PWB (BOTTOM VIEW) (2/2)
XL-DAB227NH
7 – 1
CHAPTER 7. FLOWCHART
[1] Troubleshooting
1. When the CD does not function
The CD section may not operate when the objective lens of the optical pickup is dirty. Clean the objective lens, and
check the playback operation. When this section does not operate even after the above step is taken, check the
following items.
Remove the cabinet and follow the troubleshooting instructions.
"Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the
Remove the cabinet and follow the troubleshooting instructions.
"Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the
laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned
below."
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
2. When a CD cannot be played
2.1. Pressing the CD operation key is accepted, but playback does not occur.
1) Focus-RF system check
2) Tracking system check
3) Spin system check
4) PLL system check
5) Others
Parts code
1.
CD optical pickup Lens cleaner disc
UDSKA0004AFZZ
HOW TO USE
CAUTION
Cleaning fluid
Cleaner disc
Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the
brush on the CD cleaner disc which has the mark next to it.
Place the CD cleaner disc onto the CD disc tray with the brush side down,then
press the play button.
You will hear music for about 20 seconds and the CD player will automatically stop.
If it still play continuously, press the stop button.
1.
2.
3.
The CD lens cleaner should be effective for 30-50 operations, however if the
brushes become worn out earlier then please replace the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft
cloth.
Do not drink the cleaner fluid or allow it contact with the eyes. In the event of this
happening then drink and / or rinse with clean water and seek medical advice.
The CD cleaner disc must not be used on car CD players or on computer CD-ROM
drives.
All rights reserved. Unauthorized duplicating, broadcasting and renting this product
is prohibited by law.
XL-DAB227NH
7 – 2
Although a CD is inserted and the cover is closed, "NO DISC" is displayed.
(1) Focus-RF system check.
1. Does the pickup move?
No
Sled motor (M2A).
Yes
2. Does the focus (lens) move up and down ?
(Waveform drawing Figure 1)
(Waveform drawing Figure 1)
No
Check the focus peripheral circuit.
Yes
3. Is the laser lit ?
No
Check the laser diode driver Q1 peripheral circuit.
Yes
4. Is the turntable rotating ?
No
Spindle motor (M1A).
When a disc is loaded, start playback operation.
1. Is focus servo activated ?
(Waveform drawing Figure 2)
(Waveform drawing Figure 2)
No
Pins 5, 9, 94 and 95 on IC1, Pins 1, 2, 15 and 16 on IC2.
Check the laser diode driver Q1 peripheral circuit.
Check the laser diode driver Q1 peripheral circuit.
Yes
2. Is the RF waveform normal ?
(Waveform drawing Figure 3)
(Waveform drawing Figure 3)
No
If the level is not normal.
Press the Tray1 CD Eject Button without inserting a disc, and try
starting the playback operation.
starting the playback operation.
Figure 1
Figure 2
9
10
1
2
IC1
IC1
FOO
TRO
IC1
IC1
IC1
9
6
89
4
5
1
TEI
RFO
FOO
Figure 3
IC1
89
5
RFO
XL-DAB227NH
7 – 3
Check the TE waveform at pin 6 on IC1.
(2) Tracking system check.
If the waveform shown in Figure 4 appears and soon after NO
DISC appears ?
DISC appears ?
Yes
The tracking servo is not activated.
Check the peripheral circuits at pins 6, 7, 10, 98 and 100 on
IC1, pins 17, 18, 35 and 36 on IC2 and FFC1.
Check the peripheral circuits at pins 6, 7, 10, 98 and 100 on
IC1, pins 17, 18, 35 and 36 on IC2 and FFC1.
No
"Initialization" is possible, but play is not possible ?
Yes
A normal jump operation cannot be completed or the
beginning of the track cannot be found.
Check the around pin 10 on IC1.
beginning of the track cannot be found.
Check the around pin 10 on IC1.
No
"Initialization" is not possible.
Data cannot be read. Check the VCO-PLL (Pins 72, 73, 74,
75, 76 and 78 on IC1) system.
75, 76 and 78 on IC1) system.
Figure 4
IC1
IC1
9
6
4
1
FOO
TEI
(3) Spin system check.
Press the OPEN/CLOSE switch without inserting a disc, and
then try starting the play operation.
then try starting the play operation.
1. The turntable rotates a little ?
(Waveform drawing Figure 5)
(Waveform drawing Figure 5)
Yes
The spin driver circuit is OK.
No
2. The turntable doesn't rotate.
Check around pin 13 on IC1, pins 3, 4, 13 and 14 on IC2.
Figure 5
1
6
IC1
IC1
9
13
FOO
DMO
Click on the first or last page to see other XL-DAB227NH (serv.man4) service manuals if exist.