DOWNLOAD Sharp XL-60 Service Manual ↓ Size: 852.76 KB | Pages: 36 in PDF or view online for FREE

Model
XL-60
Pages
36
Size
852.76 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Audio / System
File
xl-60.pdf
Date

Sharp XL-60 User Manual / Operation Manual ▷ View online

1
SPECIAL NOTES
NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-
rewireable (moulded) plug incorporating a 3A fuse.
Should the fuse need to be replaced, a BSI or ASTA
approved BS 1362 fuse marked 
 or 
 and of
the same rating as above, which is also indicated
on the pin face of the plug must be used.
Always refit the fuse cover after replacing the fuse.
Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your
home not being compatible with the plug supplied,
cut-off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed
and the cut-off plug destroyed immediately and
disposed of in a safe manner.
Under no circumstances should the cut-off plug
be inserted elsewhere into a 13A socket outlet as
a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow
the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in ac-
cordance with the following code:
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of
this product may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be con-
nected to the plug terminal which is marked N
or coloured black.
The wire which is coloured brown must be con-
nected to the plug terminal which is marked L or
coloured red.
Ensure that neither the brown nor the blue wire is
connected to the earth terminal in your three pin
plug.
Before replacing the plug cover, make sure that:
If the new fitted plug contains a fuse, its value is
the same as that removed from the cut-off plug.
The cord grip is clamped over the sheath of the
mains lead and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALI-
FIED ELECTRICIAN.
SERVICE INFORMATION
In the unlikely event of your equipment requiring
repair, please contact the dealer or supplier from
whom it was purchased. Where this is not possi-
ble, please contact the telephone number listed
below.
You will then be given details of how to obtain ser-
vice.
- 0345-125387 -
Please note; all calls will be charged at local rate.
Certain replacement parts and accessories may
be obtained from our main parts distributor.
WILLOW VALE ELECTRONICS LTD.
MANCHESTER 0161-682-1415
READING
01189-876444
In the unlikely event of this equipment requiring
repair during the guarantee period, you will need
to provide proof of the date of purchase to the re-
pairing company.
Please keep your invoice or receipt, which is sup-
plied at the time of purchase.
60H/70H(SUK)01-07
00.1.5, 11:38 AM
1
2
(Continued)
CAUTION
Use of controls, adjustments or performance of pro-
cedures other than those specified herein may re-
sult in hazardous radiation exposure.
As the laser beam used in this compact disc player
is harmful to the eyes, do not attempt to disassem-
ble the cabinet. Refer servicing to qualified person-
nel only.
Warning:
To prevent fire or shock hazard, do not expose
this appliance to dripping or splashing. No ob-
jects filled with liquids, such as vases, shall be
placed on the apparatus.
Recording and playback of any material may
require consent, which SHARP is unable to give.
Please refer particularly to the provisions of the
Copyright Act 1956, the Dramatic and Musical
Performers Protection Act 1958, the Performers
Protection Acts 1963 and 1972 and to any sub-
sequent statutory enactments and orders.
This equipment complies with the requirements
of Directives 89/336/EEC and 73/23/EEC as
amended by 93/68/EEC.
When the ON/STAND-BY button is set at
STAND-BY position, mains voltage is still present
inside the unit.
When the ON/STAND-BY button is set at
STAND-BY position, the unit may be brought into
operation by the timer mode or remote control.
Warning:
This unit contains no user serviceable parts.
Never remove covers unless qualified to do so.
This unit contains dangerous voltages, always
remove mains plug from the socket before any
service operation and when not in use for a long
period.
60H/70H(SUK)01-07
00.1.5, 11:38 AM
2
3
Page
ACCESSORIES ................................................. 3
PRECAUTIONS .............................................. 4-5
NAMES OF CONTROLS AND INDICATORS .. 5-7
PREPARATION FOR USE ........................... 8-10
SOUND CONTROL .................................... 10-11
SETTING THE CLOCK ................................... 12
COMPACT DISC OPERATION .................. 13-15
CASSETTE OPERATION ................................ 16
CONTENTS
Page
RADIO OPERATION .................................. 17-18
RDS (Radio Data System) OPERATION .. 19-26
RECORDING ................................................... 27
HOW TO USE THE BUILT-IN TIMER ......... 27-29
USING EXTERNAL UNITS ......................... 30-31
RESETTING THE MICROCOMPUTER ........... 31
MAINTENANCE .............................................. 31
SPECIFICATIONS ........................................... 32
PRECAUTIONS
 General
Please ensure that the equipment is positioned
in a well ventilated area and ensure that there is
at least 10cm (4”) of free space along the sides
and back. There must also be a minimum of
20cm (8”) of free space on the top of the unit.
Do not use oil, solvents, petrol, paint thinners or
insecticides on the unit.
Do not expose the unit to moisture, to tempera-
tures higher than 60
°
C (140
°
F) or to extreme low
temperatures.
Keep the unit away from direct sunlight, strong
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home comput-
ers, facsimiles, etc.) which generate electrical
noise.
Hold the AC power plug by the head when re-
moving it from the AC socket, as pulling the lead
can damage internal wires.
ACCESSORIES
● 
FM aerial 
×
 1
● 
Remote control 
×
 1
● 
AM loop aerial 
×
1
When cleaning the heads, pinch roller, etc., re-
move the AC power plug from the wall socket as
the unit contains high voltages.
Do not remove the outer cover, as this may re-
sult in electric shock. Refer internal service to
your local SHARP service facility.
Use the unit on a firm, level surface free from vi-
bration, and do not place anything on the top of
the unit.
If an electrical storm is taking place near you, it
is suggested that you disconnect the AC power
lead from the AC socket for safety.
The ventilation should not be impeded by cover-
ing the ventilation openings with items, such as
newspapers, tablecloths, curtains, etc.
No naked flame sources, such as lighted can-
dles, should be placed on the apparatus.
Attention should be drawn to the environmental
aspects of battery disposal.
The apparatus is designed for use in moderate
climate.
Note:
Parts and equipment mentioned in this operation manual other than
those in the drawing are not included.
● 
AC power lead 
×
 1
60H/70H(SUK)01-07
00.1.5, 11:38 AM
3
4
(Continued)
 Cassette tape
For playback, use normal or low-noise tape for
the best sound. (Metal or CrO
2
 tape is not rec-
ommended.)
For recording, use only normal tape.
Do not use C-120 tapes, tapes with large diam-
eter reels, or poor-quality tapes, as they may
cause malfunctions.
Before loading a tape into the cassette compart-
ment, tighten the slack with a pen or pencil.
Cassettes have removable tabs which prevent
accidental recording or erasing from taking place.
Removing the tab will protect the corresponding
side from being erased. Cover the tab holes with
adhesive tape to erase or record again.
Warning:
The voltage used must be the same as that speci-
fied on this unit. Using this product with a higher
voltage than that which is specified is dangerous
and may result in a fire or other type of accident
causing damage.
SHARP will not be held responsible for any dam-
age resulting from use of this unit with a voltage
other than that which is specified.
Volume control
The sound level at a given volume setting depends
on a combination of speaker efficiency, location and
various other factors.
It is advisable to avoid exposure to high volume
levels, which occur whilst turning the unit on with
the volume control setting up high, or whilst con-
tinually listening at high volumes.
Warning:
CD players use a laser pickup which can damage
the eyes if viewed directly. Do not look at the pickup,
and do not touch the pickup directly.
 Care of compact discs
Compact discs are fairly resistant to damage, how-
ever mistracking can occur due to the accumula-
tion of dirt on the disc surface.
Follow the guidelines below for maximum enjoy-
ment from your CD collection and player.
Do not write on either side of the disc, particu-
larly the non-label side. Signals are read from
the non-label side. Do not mark this surface.
Keep your discs away from direct sunlight, heat,
and excessive moisture.
Always hold the CDs by the edges. Fingerprints,
dirt, or water on the CDs can cause noise or
mistracking. If a CD is dirty or does not play prop-
erly, clean it with a soft, dry cloth, wiping straight
out from the centre, along the radius.
 Condensation
Sudden temperature changes, storage or opera-
tion in an extremely humid environment may cause
condensation inside the cabinet (CD pickup, tape
heads, etc.) or on the transmitter LED on the re-
mote control.
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc
(or cassette) in the unit until normal playback is
possible (about 1 hour). Wipe off any condensa-
tion on the remote control transmitter LED with a
soft cloth before operating the unit.
NO
YES
Correct
Side A (1)
Tab for side B (2)     Tab for side A (1)
60H/70H(SUK)01-07
00.1.5, 11:38 AM
4
Page of 36
Display

Sharp XL-60 User Manual / Operation Manual ▷ Download

  • DOWNLOAD Sharp XL-60 Service Manual ↓ Size: 852.76 KB | Pages: 36 in PDF or view online for FREE
  • Here you can View online or download the User Manual / Operation Manual for the Sharp XL-60 in PDF for free, which will help you to disassemble, recover, fix and repair Sharp XL-60 System. Information contained in Sharp XL-60 User Manual / Operation Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.