Sharp SD-SH111 (serv.man9) Service Manual ▷ View online
– 27 –
SD-SH111
1. Version upgrade procedure
This unit can overwrite the program inside via the dedicated cable, using the special software from PC. As this program and the
program of the drive ass’y need to be matched when replacing the drive ass’y, upgrade the firmware of this unit by following the
procedures below.
Procedures and the program version have to be changed according to the contents of service. Upgrade based on the service
information issued occasionally.
* The drive number is written on the label on each package.
Note: After version upgrade, the system must be reset, which deletes all user data in the memory. Be sure to get permission from
the user in advance.
program of the drive ass’y need to be matched when replacing the drive ass’y, upgrade the firmware of this unit by following the
procedures below.
Procedures and the program version have to be changed according to the contents of service. Upgrade based on the service
information issued occasionally.
* The drive number is written on the label on each package.
Note: After version upgrade, the system must be reset, which deletes all user data in the memory. Be sure to get permission from
the user in advance.
HOW TO SETUP THE DOWNLOAD SYSTEM:
Connection diagram
Figure 27-1
2. How to Download
Unit
Molex 2pin conector
RS-232C level
converter PWB
RUNTK0808GEZZ
QCNWK0001AWZZ
Adapter cord
RCA PIN PLUG
RCA PIN JACK
PC (DOS)
RS-232C
Figure 27-2
RS-232C cable
RS-232C
level converter
PWB
Back of the unit
Dedicated
cable
Remove the screw
Connector cover
PC
1. Doble-click the A:
∗
. exe
2. C: ¥Download directory is made when click
∗
.exe a double, and Download. exe, Control. dat, param.ini, ix
∗∗∗∗∗
.mot,
Readme_e.txt, Readme_j.txt, mod2csd.exe, crcc.exe, crc.dat and
∗∗∗∗∗∗∗∗
.txt file is made by the directory.
1. Conect the download tool (004 941 0034 [RUNTK0808GEZZ] : RS-232C Level Converter and QCNWK0001AWZZ:
connection adapter) to your PC's COM1 port.
2.Execute "download.exe"
3.Connect service tool to jack of set.
Remove the screw for the connector cover on the back of the unit and connect the cable (QCNWK0001AWZZ) to the connector.
Remove the screw for the connector cover on the back of the unit and connect the cable (QCNWK0001AWZZ) to the connector.
4.Input 1(Start)by a menu of Download.exe.
Downloader
1. Start
2. End
Select = _
1. Start
2. End
Select = _
Preparation of the DVD set
(1) While pressing down the PLAY and VOLUME UP keys
(1) While pressing down the PLAY and VOLUME UP keys
simultaneously, press the POWER key to enter the
TEST MODE.
TEST MODE.
"TEST" appears.
(2) After selecting "DVD WRITE" using the VOLUME UP/
(2) After selecting "DVD WRITE" using the VOLUME UP/
DOWN key, press the PLAY key or "6" key on the remote
control "DVD WRITE" appears.
* : it goes into the DVD ROM WRITE TEST, in more than
control "DVD WRITE" appears.
* : it goes into the DVD ROM WRITE TEST, in more than
5-second for 30-second within, on the personal
computer side. If the next data transfer mode "the
operation of 5" isn't manipulated, because it isn't
written normally. Be careful.
computer side. If the next data transfer mode "the
operation of 5" isn't manipulated, because it isn't
written normally. Be careful.
SD-SH111
– 28 –
DVD TEST MODE
A POWER key is pushed, and POWER should be turned
A POWER key is pushed, and POWER should be turned
off.
(1) While pressing down the PLAY and VOLUME UP keys
simultaneously, press the POWER key to enter the
TEST MODE.
TEST MODE.
"TEST" appears.
(2) After selecting "DVD" using the VOLUME UP/DOWN
(2) After selecting "DVD" using the VOLUME UP/DOWN
key, press the PLAY key or "2" key on the remote
control. "DVD TEST" appears.
control. "DVD TEST" appears.
With the number of the part **** of the program file name
####****##.exe. It confirms that the version number of TV
screen corresponds.
If the old version number is displayed, stop with [ESC] key
and cut off a set, and repeat a download from setp 5.
####****##.exe. It confirms that the version number of TV
screen corresponds.
If the old version number is displayed, stop with [ESC] key
and cut off a set, and repeat a download from setp 5.
5.Input "Enter" if heard it with Soft-ware Updata Start?
Update File =
∗∗∗∗∗∗
Start Address = 0x010000
Soft-ware Update Start ? :
Start > [Enter]
Exit > [ESC]
Wait Change > [W]
Start > [Enter]
Exit > [ESC]
Wait Change > [W]
6.when data transmission is started, PC side shows "%"
indication, and it is indicated with "W:STR" by set FIP.
7.When a download is successful, 100% is indicated in PC
side. When this indication doesn't appear, stop with [ESC]
key and cut off a set,and repeat a download from setp5.
Version confirming procedures. Connect this unit to the TV
monitor and check the version number on the TV screen in
the DVD TEST MODE. If the new version number is
displayed, the operation is completed.
key and cut off a set,and repeat a download from setp5.
Version confirming procedures. Connect this unit to the TV
monitor and check the version number on the TV screen in
the DVD TEST MODE. If the new version number is
displayed, the operation is completed.
Update File =
∗∗∗∗∗∗
Start Address = 0x010000
Soft-ware Up (CANCEL Push ESC)
100 %
100 %
Continue –> Push Anykey
Cancel –> Push ESC
Cancel –> Push ESC
10. Input "ESC" if heard it with Soft-ware Updata Start?
11. Input "y" if heard it with Exit (Y/N)?
Update File =
∗∗∗∗∗∗
Start Address = 0x010000
Soft-ware Up (CANCEL Push ESC)
∗∗
%
_
DVD TEST MODE
F00000000 ###
∗∗∗∗#
TV screen
∗∗∗∗
: Ver No.
8.In a normal end, cut a power supply of the set side after
avoiding the tool.
9.Input "ESC" if heard it with Cpntinue / Cancel ?
Update File =
∗∗∗∗∗∗
Start Address = 0x010000
Soft-ware Update Start ? :
Start > [Enter]
Exit > [ESC]
Wait Change > [W]
Start > [Enter]
Exit > [ESC]
Wait Change > [W]
Update File =
∗∗∗∗∗∗
Start Address = 0x010000
Soft-ware Update Start ? :
Start > [Enter]
Exit > [ESC]
Wait Change > [W]
Start > [Enter]
Exit > [ESC]
Wait Change > [W]
Exit? (Y/N) Y
Program Exit
11. Input "y" if heard it with Exit (Y/N)?
Update File =
∗∗∗∗∗∗
Start Address = 0x010000
Soft-ware Update Start ? :
Start > [Enter]
Exit > [ESC]
Wait Change > [W]
Start > [Enter]
Exit > [ESC]
Wait Change > [W]
Exit? (Y/N) Y
Program Exit
C: ¥DOWNLOAD>
Display
