DOWNLOAD Sharp QT-CD250 (serv.man4) Service Manual ↓ Size: 337.98 KB | Pages: 12 in PDF or view online for FREE

TO

<P=001>

■

To AC INPUT

AC 230-240 V, 50 Hz

 To an AC socket

Connect the AC power lead to the AC power input
socket, then connect the AC power lead plug to an
AC socket.

●

If the unit will not be used for a long period of
time, remove the AC power lead from the AC
socket.

●

Connection of the AC power lead to the unit
disconnects the batteries.

●

Never use a power lead other than the one
supplied. Use of a power lead other than the one
supplied may cause an electric shock or fire.

■

5

4

6

1

3

2

1

Disconnect the AC power lead, and remove the
battery compartment cover.

Insert 6 "D" size batteries (UM/SUM-1, R20,
HP-2 or similar) into the battery compartment.

●

Insert the batteries according to the direction
indicated on the rear panel.

●

When inserting or removing the batteries 

③

 and

⑥

, push them towards the 

ë

 battery terminals. 

●

Installing the batteries incorrectly may cause the
unit to malfunction.

Replace the battery compartment cover.

Note:
Replace the batteries when they become weak
and/or recording or playback is impaired. This may
occur even though radio broadcasts are audible.

15

15

1

Remove the battery compartment cover on the
remote control.

2

Insert 2 "AA" size batteries (UM/SUM-3, R6,
HP-7 or similar) into the battery compartment on
the remote control.

●

When inserting or removing the batteries, push
them towards the 

ë

 battery terminals.

●

Installing the batteries incorrectly may cause the
unit to malfunction.

●

Replace the batteries if the operating distance is
reduced or if the operation becomes erratic.

●

Periodically clean the transmitter LED on the
remote control and the sensor on the main unit
with a soft cloth.

●

Exposing the sensor on the main unit to strong
light may interfere with operation. Change the
lighting or the direction of the unit.

●

Keep the remote control away from moisture,
excessive heat, shock, and vibrations.

Remote sensor

0.2 m - 6 m
(8" - 20’)

QT-CD250H(SUK) TINSE0043SJZZ

<P=002>

■

Set the function switch to CD.

Press the CD EJECT button to open the CD
compartment.

Place a compact disc on the spindle, label side
up.

●

8 cm (3") discs may be played without an adap-
tor.

Close the CD compartment by firmly pushing the
right corner of it.

Total number of
tracks

Total playing time

Press the PLAY/PAUSE (

0 6

) button to start

playback from track 1.

6

Press the VOLUME up button to increase the
volume and the VOLUME down button to de-
crease the volume.

7

Press the X-BASS button to emphasise the bass
region of the frequency spectrum.
The "X-BASS" indicator will light up.
Press the X-BASS button again to cancel the
extra bass mode.
The "X-BASS" indicator will go out.

To interrupt playback:
Press the PLAY/PAUSE (

0 6

) button during play-

back.
Press the PLAY/PAUSE (

0 6

) button again to

resume playback.

Press the STOP (

■

) button.

●

When "no dISC" or track number is displayed,
the power is connected.
If you will not be using the CD player, set the
ON/STAND-BY switch to STAND-BY.

●

Do not open the CD compartment whilst the
disc is rotating.

●

If the disc is damaged, dirty, or loaded upside
down, "Er" or "no dISC" will appear in the
display.
Clean, replace, or reload the disc properly.

●

Keep foreign objects out of the CD compart-
ment.

●

Subjecting the unit to shock or vibration may
cause mistracking.

●

Keep the CD compartment closed except
when loading discs.

●

Playing certain compact discs at a high vol-
ume may cause mistracking. In this case,
listen at a lower volume.

●

The temperature range for playing compact
discs is recommended to be 5˚C (41˚F) - 35˚C
(95˚F).

●

If TV or radio interference occurs during CD
operation, move the unit away from the TV or
radio.

QT-CD250H(SUK) TINSE0043SJZZ

<P=003>

■

APSS automatically locates the beginning of any
track.

To listen again to the track being played:
Press the DOWN (

3 / 5

) button for less than 0.5

seconds during playback.

To move to the beginning of the next track:
Press the UP (

2 / 4

) button for less than 0.5

seconds during playback.

●

To skip a number of tracks at one time, press the
UP (

2 / 4

 ) or DOWN (

3 / 5

 ) button

repeatedly until the desired track number is
shown.

●

To start playback from a desired track, press the
UP (

2 / 4

) or DOWN (

3 / 5

) button whilst

in the stop mode to select the track number, and
then press the PLAY/PAUSE (

0 6

) button.

■

During playback, press the REPEAT/BAND (

R

) but-

ton repeatedly to select the play mode.
Each time the button is pressed, the display will
change as follows:

Flash

1 track repeat play

Appear

All track repeat play

Disappear

Normal play

Repeat play indicator

●

When using repeat play, be sure to press the
STOP (

■

) button after you are through listening. 

Otherwise, the CD(s) will play continuously.

■

Load a disc and begin playback.

Hold down the CUE (

2 / 4

) button for audible

fast forward, and hold down the REVIEW (

3 /

5

) button for audible fast reverse.

Normal playback will resume when the REVIEW
(

3 / 5

) or CUE (

2 / 4

) button is released.

●

When the end of the disc is reached whilst
cueing, "End" will appear in the display and CD
operation is paused. Press the REVIEW (

3 /

5

) button for fast reverse or press the STOP

(

■

) button to stop CD operation.

●

If the beginning of the disc is reached whilst
reviewing, the mode will automatically switch to
normal playback at that point.

QT-CD250H(SUK) TINSE0043SJZZ

<P=004>

■

Set the function switch to TAPE.

Load the cassette into the cassette compart-
ment.

Press the PLAY button.

To advance the tape, press the STOP/EJECT
button, then press the F FWD button. To rewind,
press the STOP/EJECT button, then press the
REWIND button.

To interrupt playback:
Press the PAUSE button during playback.
Press the PAUSE button again to resume playback.

To stop playback:
Press the STOP/EJECT button.

●

Be sure not to press the PLAY and REWIND
buttons simultaneously, or the tape will become
damaged.

●

Before changing from one tape operation to an-
other, press the STOP/EJECT button.

●

Do not press the PAUSE button whilst the fast
forward or rewind operations are in progress.
The F FWD or REWIND button will not be re-
leased when the tape end is reached. Once this
occurs, press the STOP/EJECT button.

●

Before plugging in or unplugging the head-
phones, make sure the volume level is reduced.

●

Be sure your headphones have a 3.5 mm (1/8")
diameter plug and are between 16 ohms and 50
ohms impedance. The recommended imped-
ance is 32 ohms.

●

Connect the headphones plug to the PHONES
socket located on the rear of the unit. The spea-
kers will be automatically disconnected. Adjust
the volume by using the VOLUME control.

QT-CD250H(SUK) TINSE0043SJZZ