Sharp QT-120H User Manual / Operation Manual ▷ View online
<P=002>
POWER SOURCE
■
AC power
Connect the AC power lead to the AC power input socket,
then connect the AC power lead plug to an AC socket.
then connect the AC power lead plug to an AC socket.
Notes:
●
If the unit will not be used for a long period of time, remove
the AC power lead from the AC socket.
the AC power lead from the AC socket.
●
When the AC power lead is plugged into the back of the
unit, the batteries are automatically disconnected.
unit, the batteries are automatically disconnected.
●
Never use a power lead other than the one supplied. Other-
wise, a malfunction or an accident may occur.
wise, a malfunction or an accident may occur.
●
If a humming noise occurs, turn the power plug upside
down where it is connected to the AC power input socket
on the unit.
down where it is connected to the AC power input socket
on the unit.
■
Battery power
1
Disconnect the AC power lead, and remove the battery
compartment cover.
compartment cover.
●
Use of the AC power lead disconnects the batteries.
2
Insert 8 "D" size batteries (UM/SUM-1, R20, HP-2 or simi-
lar) into the battery compartment.
lar) into the battery compartment.
●
When inserting batteries
④
and
⑧
, push them towards the
ë
battery terminal.
●
Installing the batteries incorrectly may cause the unit to
malfunction.
malfunction.
3
Replace the battery compartment cover.
Battery removal:
●
Push batteries
④
and
⑧
towards the
ë
battery terminal
and remove them.
Precautions for battery use:
●
Insert the batteries according to the direction indicated on
the rear panel.
the rear panel.
●
Remove the batteries if they are weak or if the unit is not
in use for long periods to prevent potential damage due
to battery leakage.
in use for long periods to prevent potential damage due
to battery leakage.
●
Replace all old batteries with new ones at the same time.
●
Do not mix old and new batteries.
Caution:
Do not use rechargeable batteries (nickel-cadmium battery,
etc.).
Do not use rechargeable batteries (nickel-cadmium battery,
etc.).
Battery replacement:
Replace the batteries when they become weak and recording
or playback is impaired. This may occur even though radio
broadcasts are audible.
or playback is impaired. This may occur even though radio
broadcasts are audible.
To an AC socket
AC 230 V, 50 Hz
2
1
6
7
3
2
1
8
4
5
QT-120H(SUK) ?????????????
3
<P=003>
SOUND CONTROL
Volume
Rotate the VOLUME control towards MAX to increase the
volume, and towards MIN to decrease the volume.
The loudness circuit is activated automatically when the vol-
ume is low to emphasise low frequencies.
volume, and towards MIN to decrease the volume.
The loudness circuit is activated automatically when the vol-
ume is low to emphasise low frequencies.
Extra bass (X-BASS)
Move the X-BASS control towards MAX to emphasise bass
sound.
The centre position represents a normal setting.
sound.
The centre position represents a normal setting.
Graphic equalizer
Move the GRAPHIC EQUALIZER control for any frequency
towards
towards
+
10 to boost the level for that frequency, and to-
wards
−
10 to lower the level.
RADIO OPERATION
1
Set the TAPE/RADIO switch to RADIO.
2
Set the BAND SELECTOR switch to FM, MW or LW.
3
Use the TUNING control to tune in to the desired station.
4
To receive an FM stereo transmission, set the FM
MONO/FM ST switch to FM ST.
MONO/FM ST switch to FM ST.
5
If the FM reception is weak, set the FM MONO/FM ST
switch to FM MONO.
switch to FM MONO.
●
Although the reception changes to monaural, the sound
becomes clearer.
becomes clearer.
MIN
VOLUME
MAX
X-BASS
MAX
MIN
1kHz
10kHz
10
10
0
GRAPHIC
EQUALIZER
Aerial adjustment
FM
MW/LW
To switch the unit off after use:
Set the STAND-BY/ON switch to STAND-BY.
TUNING
TAPE
FM ST
FM MONO
RADIO
STAND-BY
ON
BAND SELECTOR
1,4,5
3
2
FM
LW
MW
U
M
L
QT-120H(SUK) ?????????????
4
<P=004>
CASSETTE OPERATION
■
General information
●
For playback, use normal or low-noise tape for the best
sound. (Metal or CrO
sound. (Metal or CrO
2
tape is not recommended.)
For recording, use only normal tape.
●
Do not use C-120 tapes, tapes with large diameter reels,
or poor-quality tapes, as they may cause malfunctions.
or poor-quality tapes, as they may cause malfunctions.
●
Before loading a tape into the cassette compartment,
tighten the slack with a pen or pencil.
tighten the slack with a pen or pencil.
●
Cassettes have removable tabs which prevent accidental
recording or erasing from taking place. Removing the tab
will protect the corresponding side from being erased.
Cover the tab holes with adhesive tape to erase or record
again.
recording or erasing from taking place. Removing the tab
will protect the corresponding side from being erased.
Cover the tab holes with adhesive tape to erase or record
again.
■
Playback
1
Set the TAPE/RADIO switch to TAPE.
2
Press the STOP/EJECT button and load a cassette into
the cassette compartment.
the cassette compartment.
3
Press the PLAY button.
4
To advance the tape, press the STOP/EJECT button,
then press the F FWD button. To rewind, press the
STOP/EJECT button, then press the REWIND button.
then press the F FWD button. To rewind, press the
STOP/EJECT button, then press the REWIND button.
To interrupt playback:
Press the PAUSE button during playback.
Press the PAUSE button again to resume playback.
Press the PAUSE button again to resume playback.
To stop playback:
Press the STOP/EJECT button.
Precautions:
●
Be sure not to press the PLAY and REWIND buttons sim-
ultaneously, or the tape will be damaged.
ultaneously, or the tape will be damaged.
●
Before changing from one tape operation to another, press
the STOP/EJECT button.
the STOP/EJECT button.
●
When the end of the tape is reached during the recording,
playback, fast forward or rewind mode, the full auto stop
system is activated and automatically puts the unit into the
neutral (stop) mode.
playback, fast forward or rewind mode, the full auto stop
system is activated and automatically puts the unit into the
neutral (stop) mode.
●
If the PAUSE button is pressed whilst the fast forward or
rewind operation is in progress, the F FWD or REWIND
button will not be released when the tape end is reached.
In this case, press the STOP/EJECT button.
rewind operation is in progress, the F FWD or REWIND
button will not be released when the tape end is reached.
In this case, press the STOP/EJECT button.
1
2
2
3
REWIND PAUSE
F FWD
TAPE
FM ST
FM MONO
RADIO
STAND-BY
ON
Side A (1)
Tab for side B (2)
Tab for side A (1)
QT-120H(SUK) ?????????????
5
YO
<P=001>
RECORDING
●
When recording important selections, be sure to make a
preliminary test to ensure that the desired material is being
properly recorded.
preliminary test to ensure that the desired material is being
properly recorded.
●
The ALC (Automatic Record Level Control) circuit auto-
matically controls the level of the input signal used for
recording.
matically controls the level of the input signal used for
recording.
●
The VOLUME, X-BASS and GRAPHIC EQUALIZER con-
trols may be adjusted with no effect on the recorded sig-
nal. (Variable Sound Monitor)
trols may be adjusted with no effect on the recorded sig-
nal. (Variable Sound Monitor)
●
Metal and CrO
2
tapes cannot be used for recording.
■
Recording from the built-in radio
1
Tune in to the desired station. (See page 4.)
2
Load a cassette into the cassette compartment.
3
Press the PAUSE button.
4
Press the RECORD button, which also engages the
PLAY button.
PLAY button.
5
Press the PAUSE button again to begin recording.
Beat cancel switch:
If a whistling noise occurs when recording from an MW or
LW station, set the BEAT CANCEL switch to A, B or C,
whichever gives the best reception.
LW station, set the BEAT CANCEL switch to A, B or C,
whichever gives the best reception.
■
Recording from the built-in microphone
1
Set the TAPE/RADIO switch to TAPE.
2
Load a cassette into the cassette compartment.
3
Press the PAUSE button.
4
Press the RECORD button, which also engages the
PLAY button.
PLAY button.
5
Press the PAUSE button again to begin recording.
Notes:
●
Monitoring of the recording is not possible.
●
Recording from the built-in microphone is not in stereo.
A
BEAT
CANCEL
B
C
TUNING
1
2
4
3,5
HEADPHONES
PHONES
●
Be sure that your headphones have a 3.5 mm (1/8")
diameter plug and are between 16 ohms and 50 ohms
impedance. The recommended impedance is 32 ohms.
diameter plug and are between 16 ohms and 50 ohms
impedance. The recommended impedance is 32 ohms.
●
Connect the headphones plug to the PHONES socket. The
speakers will be automatically disconnected. Adjust the
volume by using the VOLUME control.
speakers will be automatically disconnected. Adjust the
volume by using the VOLUME control.
QT-120H(SUK) ?????????????
6
Display
