DOWNLOAD Sharp DK-A10H (serv.man3) Service Manual ↓ Size: 13.25 MB | Pages: 82 in PDF or view online for FREE

DK-A10H/DK-A10H(BK)

2 – 2

a) Unit will Power On in TUNER function.
b) Preset will be writen as shown below for each destination

ΰFM MONO BAND α

c) Receiving Preset No. 1
d) End TEST mode if POWER key is press

ΰ All preset will be deleted α.

e) VOLUME setting is 25.

Reference

M1

M2

M3

M4

M5

M6

M7

M8

M9

M10

 SPAN

μDisplayν

At Tuner function only "FM" or "AM" will blinking during Test Mode.

EUROPE

Destination

TUNER PRESET MEMORY

It is possible to read setting value after Auto Adjustment(to judge between initial value) 

To force movement of pick-up 

Inner Move, Outer Move, LD ON/OFF

To display accumulate error total for 10sec while PLAY(about 750frame at normal)

(For this model it is not count by Frame Method, but 10sec timer Accumulated Error Total
and not related Frame total)

4 x CLV trace but, no sound output.

1) Direct POWER ON in CD function.

2)  Execute initial process to DSP.

3)  Send command correspondence to key.

Valid key 

Κ PLAY/PAUS EΕSTOPΕSKIP-UP/CUE ΕSKIP-DWN/REV Ε

POWER

ΕDISPLAYΕVOL UP/DWN ΕCD EJECT ΕCD

Additional

ΚIf which one of KEY1 + KEY2 press together All FL segment will light up.

.

KEY_2-6_

CLOCK DISPLAY "0:00”
SUMMER TIME COMFIRMATION

CLOCK

KEY_1-6_ + BUZZER 2
(B pattern VOLUME25

α

KEY_1-7_ + BUZZER 3
(B pattern VOLUME25

α

CD

iPod

KEY NAME

ALARM ON/OFF

ALARM

KEY
TEST MODE

DISPLAY

KEY_1-5_ + BUZZER 1
(B pattern VOLUME25

α

KEY_2-1_

KEY_2-2_

KEY_2-3_

KEY_2-4_

KEY_2-5_

TUNER

AUX

SNOOZE/DIMMER

KEY_1-2_

KEY_1-3_

KEY_1-4_

KEY
TEST MODE

DISPLAY

KEY_1-1_

REVIEW

PLAY/PAUSE

KEY NAME

E SOUND

VOL UP

VOL DOWN

CD EJECT

KEY_3-1_

KEY_2-7_

KEY NAME

KEY
TEST MODE
DISPLAY

EQ

CUE

87.50 108.00  90.00 106.00  98.00  522K  1620K  603K 1404K  990K  50K/9K

DK-A10H/DK-A10H(BK)

2 – 3

By pressing DISPLAY key while PLAY, will display Accumulate Error Total for 10sec time
(about 750frame at normal)

Read Method

1.  Send PRCSET (9188) command EC/FC=H
2.  Observe BUS2 while in idle mode, If become "H"(Sub-CODE read possible)
     by (SRC6) read command Error Total for 1 frame are read.
3.  This process will repeat for every 10sec, the value will be display. And renew for every 10sec.
4.  While displaying ERR, if Display key input detected it will return to TEST MODE normal display.

Additional

1.   STEP No. is, ”0” 

Д “5”. ”0” is STOP condition.

2.   Adjustment Value Read or Error Total Read are display on FL.

Read Error Total 

Κ “ҟҠϵҡҮҮϵϠϠϠϠ”

“

ϠϠϠϠ”is Error Total

A.   PLAY/PAUSE

ΚCD operation by steps

STEP1

ΚPLAY/PAUSE key from STOP condition,  LD ON

STEP2

ΚPLAY/PAUSE key from STEP1 condition,  FOCUS ON

STEP3

ΚPLAY/PAUSE key from STEP2 condition,  CLV SERVO ON

STEP4

ΚPLAY/PAUSE key from STEP3 condition,  Tracking Servo ON

STEP5

ΚPLAY/PAUSE key from STEP4 condition,  Read and Display Sub-CODE

Ϡ by pressing PLAY/PAUSE key over 1sec, direct go to STEP5.

B.   STOP

ΚPLAY condition to STOP(each step go to STOP )

RESET display

ΰwhile display coefficient α

C.   SKIP-UP/CUE

ΚForce to move Pick-UP FWD direction

D.   SKIP-DWN/REV

ΚForce to move Pick-UP REV direction

If PU_IN_SW ON, slide will STOP.

E.   CD

ΚOnly recognize long press, Execute Auto AdjustΰAt now Pick-UP position

α

F.   POWER

ΚEnd Test Mode

G.   DISPLAY

ΚWhile CD STOP, Read Coefficient Register
While CD PLAY, Error Total display

H.   VOL-UP/DWN

ΚNormal VOLUMEControl.

I. CD EJECT

: While STOP (After go to STOP from each step), CD EJECT process.

J. E SOUND

: While STOP toggle between 2x mode  ←→ 1x mode.
  BASS indicator ON while 2x mode.

By pressing DISPLAY key while STOP, begin read below items.
Pressing STOP key, return to Normal Display.

ITEMS

DISPLAY

Κ“ ”IS BLANK,“ҴҴ”IS ADJUST VALUE or READ VALUE

Focus Balance

ҢҞΚҴҴ

Focus Gain

ҢңΚҴҴ

Tracking Balance

ҰҞΚҴҴ

Tracking Gain

ҰңΚҴҴ

Focus OFFSET

ҢҫҢҢΚҴҴ

Tracking OFFSET

ҰҫҢҢΚҴҴ

RFRP

ҮҢҮҬΚҴҴ

Focus Error(RW judge)

ҮҳΚҴҴҴҴҴҴ

Focus Error(not RW judge)

ҠҝΚҴҴҴҴҴҴ

Setting register by D4XX(FTBAST) after, read register by 2XX(SRC2)

DK-A10H/DK-A10H(BK)

2 – 4

A Test Mode to apply improvement patch if happen bug in Micom Mask IC, 

a) POWER ON in display porpose Power ON.
b) Check port setting, if set to EEPROM exist, go to EEPROM write standby condition. 

c) DATA being send from PC using RS232C port, DATA will be transfer to EEPROM. 

d) After finished transfer, EEPROM writing port will be set to write prohibit.
e) By pressing POWER key test mode end and RESET process will be execute.

CONDITION

LED CONT 1/2  ALARM LED

READY TO RECEIVE DATA

ON

ON

WRITING

BLINK

OFF

WRITING END

ON

OFF

WRITING ERROR

OFF

BLINK

  It possible to write software to FLASH using CD-R. This Test Mode is to set enviroment 
  for writing process.

System MICOM will POWER ON in CD function.

SYS Side

Κ

Ѿα Enter "ROMCF____" and display will show“FLASH_WR_”.
ѿα Load CD-R that only being copy with *.MOT file.
Ҁα Unit will automatically enter UPDATE Mode after reading DATA.
ҁα SNOOZE_LED will blink during Writing Process.
҂α After succeed writing SNOOZE_LED will light up.
҃α If error happen ALARM_LED will start blinking.
҄α Take out DISC after the DISC EJECTED.
҅α RESET will be display due to POWER key press if writing process succeed.
҆α Test Mode end without reseting for error writing if POWER key pressed.

  It possible to write PATCH to EEPROM using CD-R. This Test Mode is to set enviroment 
  for writing process.

System MICOM will POWER ON in CD function.

SYS Side

Κ

Ѿα Enter ROMCE and display will show “EEPROM_WR”.
ѿα Load CD-R that only being copy with *.MOT file.
Ҁα Unit will automatically enter UPDATE Mode after reading DATA.
ҁα LED CONT1/2 will blink 1Hz during Writing Process.
҂α After succeed writing LED CONT1/2 will light up.
҃α If error happen ALARM_LED will start blinking 2Hz.
҄α Unit will Automatically RESET, if writing process succeed.
҅α RESET will be display due to POWER key press if writing process fail.

DK-A10H/DK-A10H(BK)

2 – 5

No.

USER RESET

1

 ALL 

CLEAR(RESET)

Function                            :

  Software RESET

                                   :

All the function

                                   :

After display "CLEAR ALL", power will off.

                                   :

Initial condition set for iPod

"CLEAR_ ALL" shown at display

Direct Access

POWER + SNOOZE/DIMMER + iPod MODE