Sharp CP-SW1000H User Manual / Operation Manual ▷ View online
E-5
ENGLISH
CP-SW1000H
Preparation for Use
Subwoofer connections to TVs
Caution:
Turn off all other equipment before making any connections.
Notes:
Refer to the operation manual of the equipment to be connected.
Fully insert the plugs to avoid fuzzy pictures or noises.
Caution:
Tuner receiving for other audio system
Tuner receiving for other audio system
Placing the aerial near the subwoofer unit AC power lead may
cause noise pick up. Place the aerial away from the subwoofer
unit for better reception.
cause noise pick up. Place the aerial away from the subwoofer
unit for better reception.
Connecting to a TV
If the TV/monitor has an audio output, connect it to the AUDIO
INPUT sockets on the rear of the subwoofer.
INPUT sockets on the rear of the subwoofer.
Connecting to a TV (with subwoofer pre-out)
If the TV/monitor has subwoofer pre-out, connect it to the AUDIO
INPUT sockets on the rear of the subwoofer.
INPUT sockets on the rear of the subwoofer.
TV
To audio output sockets
Audio cable (supplied)
Subwoofer
To AUDIO
INPUT sockets
INPUT sockets
To SUBWOOFER PRE-OUT
socket
socket
Audio cable (supplied)
Subwoofer
To AUDIO
INPUT sockets
INPUT sockets
TV
E-6
ENGLISH
9
CP-SW1000H
Preparation for Use
AC power connection
After checking all the connections have been made correctly,
connect the AC power lead to the AC power input socket, then to the
wall socket.
connect the AC power lead to the AC power input socket, then to the
wall socket.
Notes:
Never use a power lead other than the one supplied. Otherwise,
a malfunction or an accident may occur.
a malfunction or an accident may occur.
Unplug the AC power lead from the wall socket if the unit will not
be in use for a prolonged period of time.
be in use for a prolonged period of time.
Remote control
Battery installation
Precautions for battery use:
Remove the battery if the unit will not be used for long periods of
time. This will prevent potential damage due to battery leakage.
time. This will prevent potential damage due to battery leakage.
Caution:
Do not use rechargeable battery (nickel-cadmium battery, etc.).
Replace only with the same or equivalent type.
Installing the battery incorrectly may cause the unit to malfunction.
Danger of explosion if battery is incorrectly replaced.
Batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
Replace only with the same or equivalent type.
Installing the battery incorrectly may cause the unit to malfunction.
Danger of explosion if battery is incorrectly replaced.
Batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
Wall socket
(AC 220 - 240 V ~ 50 Hz (Europe))
(AC 220 - 240 V ~ 50/60 Hz (others))
(AC 220 - 240 V ~ 50 Hz (Europe))
(AC 220 - 240 V ~ 50/60 Hz (others))
1
Whilst pushing the locking tab towards the centre of the
remote control, slide out the battery holder.
remote control, slide out the battery holder.
2
Remove the old battery from the battery holder, insert the
new battery and then slide the battery holder back into the
remote control.
new battery and then slide the battery holder back into the
remote control.
Back of remote control
Locking tab
Battery holder
Polarity (+) symbol
Battery type
Locking tab
Positive (+) side up
E-7
ENGLISH
CP-SW1000H
Preparation for Use
Remote control (continued)
Notes concerning use:
Replace the battery if the operating distance is reduced or if the
operation becomes erratic. Purchase “CR 2025”, coin lithium
battery.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
Keep the remote control away from moisture, heat, shock, and
vibrations.
operation becomes erratic. Purchase “CR 2025”, coin lithium
battery.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy your system.
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy your system.
General control
To turn the power on
Remote sensor
0.2 m - 6 m
(8” - 20’)
(8” - 20’)
15˚ 15˚
0.2 m - 6 m
(8” - 20’)
(8” - 20’)
15˚ 15˚
Remote sensor
Position A
Position B
Press the ON/STAND-BY button.
The volume indicator lights up
blue.
If the power does not turn on,
check whether the power lead is
plugged in properly.
The volume indicator lights up
blue.
If the power does not turn on,
check whether the power lead is
plugged in properly.
To set the unit to stand-by mode:
Press the ON/STAND-BY button
again.
The STAND-BY indicator lights up
red.
Press the ON/STAND-BY button
again.
The STAND-BY indicator lights up
red.
(Lights
up blue)
(Turns red)
E-8
ENGLISH
9
CP-SW1000H
Advanced Feature
Volume control
Main unit operation:
Turn volume knob clockwise to increase the volume and anti-
clockwise to decrease the volume.
Remote control operation:
Press the VOL + button to increase the volume and the VOL – button
to decrease the volume.
Note:
Do not turn the volume knob manually in reverse direction when
operating it by remote control.
Turn volume knob clockwise to increase the volume and anti-
clockwise to decrease the volume.
Remote control operation:
Press the VOL + button to increase the volume and the VOL – button
to decrease the volume.
Note:
Do not turn the volume knob manually in reverse direction when
operating it by remote control.
Crossover frequency control
Adjust the high frequency cut-off point. Frequencies higher than the
set frequency are removed.
To emphasise the bass, turn this control towards 80 Hz and increase
the volume.
set frequency are removed.
To emphasise the bass, turn this control towards 80 Hz and increase
the volume.
Notes:
Observe the following to avoid malfunction and sound distortion.
Observe the following to avoid malfunction and sound distortion.
Do not set the volume too high on the audio system. The
subwoofer may be damaged.
Before you switch on/off the subwoofer, minimise the volume on
the audio system.
subwoofer may be damaged.
Before you switch on/off the subwoofer, minimise the volume on
the audio system.
Auto power off
If no signal is detected for 20 minutes during power on, the
subwoofer will automatically go to stand-by mode.
subwoofer will automatically go to stand-by mode.
Operating the TV with the remote
control
control
You can operate SHARP TV with this system’s remote control.
Watching TV
Other operable button
Press the Input Select button to switch the input source. (TV)
Note:
Some models of SHARP TV may not be operable. In this case, use
the remote control supplied with each product.
Press the Input Select button to switch the input source. (TV)
Note:
Some models of SHARP TV may not be operable. In this case, use
the remote control supplied with each product.
Point the remote control at the TV.
1
Press the TV POWER button to turn on the TV.
2
Press the CH UP or CH DOWN button to set the
channel.
Pressing the CH UP
channel.
Pressing the CH UP
or CH DOWN
button enables TV
channel switching.
3
Press TV VOL + or – button to adjust the TV volume.
TV operation buttons
Click on the first or last page to see other CP-SW1000H service manuals if exist.