Sharp CP-SW1000H (serv.man2) Service Manual ▷ View online
CP-SW1000H
1 – 3
CHAPTER 1. GENERAL DESCRIPTION
[2] Specifications
[1] Important Service Notes (for U.K. only)
Before returning the unit to the customer after completion of a repair or adjustment it is necessary for the following withstand voltage test to be
applied to ensure the unit is safe for the customer to use.
applied to ensure the unit is safe for the customer to use.
Setting of Withstanding Voltage Tester and set.
Set name
set value
Withstanding Voltage Tester
Test voltage
Test voltage
4,240 VPEAK
3,000 VRMS
3,000 VRMS
Set time
6 secs
Set current (Cutoff current)
4 mA
Unit
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzer sounds.
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzer sounds.
PROBE
AC
OUT
AC/DC
ADAPTOR
SHORT-CIRCUIT
AC POWER
AC POWER
SUPPLY CORD
CONNECT THE PROBE
TO SHELL OF DC CONNECTOR
WITHSTANDING
VOLTAGE TESTER
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.
CP-SW1000H
CP-SW1000H for U.K.
General
Power source
AC 220 - 240 V ~ 50 Hz
Power consumption
Power on: 18 W
Power stand-by: 0.6 W(*)
Power stand-by: 0.6 W(*)
Amplification system
Subwoofer: Pulse width modulation
Output power
RMS: 100 W (50 W + 50 W) (DIN 45 324)
Audio input terminal
Analog input: RCA type x 1 pair (L/R)
Type
Subwoofer system
Impedance
4 ohms x 2
Dimensions
Width: 430 mm (16-15/16")
Height: 151 mm (5-15/16")
Depth: 323.5 mm (12-3/4")
Height: 151 mm (5-15/16")
Depth: 323.5 mm (12-3/4")
Weight
6.4 kg (14.11 lbs.)
Crossover frequency
80 Hz - 220 Hz
( * ) This power consumption value is obtained when in the power
stand-by mode.
CAUTION: “Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type”.
or equivalent type”.
General
Power source
AC 220 - 240V ~ 50 Hz
Power consumption
Power on: 18 W
Power stand-by: 0.6 W(*)
Power stand-by: 0.6 W(*)
Amplification system
Subwoofer: Pulse width modulation
Output power
RMS: 100 W (50 W + 50 W) (10% T.H.D.)
Audio input terminal
Analog input: RCA type x 1 pair (L/R)
Type
Subwoofer system
Impedance
4 ohms x 2
Dimensions
Width: 430 mm (16-15/16")
Height: 151 mm (5-15/16")
Depth: 323.5 mm (12-3/4")
Height: 151 mm (5-15/16")
Depth: 323.5 mm (12-3/4")
Weight
6.4 kg (14.11 lbs.)
Crossover frequency
80 Hz - 220 Hz
( * ) This power consumption value is obtained when in the power stand-
by mode.
1 – 1
CP-SW1000H
1 – 4
[3] Names Of Parts
5 6
4
3
2
1
1 2 3
2
4
3
1
Front panel
1. Bass Reflex Duct
2. Remote Sensor
3. Volume Control
4. Crossover Frequency Control
5. ON/STAND-BY Button
6. STAND-BY Indicator
Rear panel
1. AC Input
2. Cooling Fan
3. Audio Input
Remote control
1. Remote Control Transmitter
2. On/Stand-by Button
3. TV Operation Buttons
4. Volume Up and Down Buttons
1 – 2
CP-SW1000H
2 – 1
Figure 1
Figure 4
Figure 3
Figure 2
(A1)x6
M4x16mm
M4x16mm
Back Panel
(D1)x6
M3x15mm
M3x15mm
(C1)x12
M3.5x14mm
M3.5x14mm
Speaker
Front Panel Ass’y with PWB
(D2)x2
M3x15mm
M3x15mm
(B1)x6
M4x20mm
M4x20mm
Back Board
(E1)x2
M4x16mm
M4x16mm
CD-ES700/CD-ES77
CD-ES700/CD-ES77
Service Manual
CD-ES700/CD-ES77
Market
E
CHAPTER 2. MECHANICAL DESCRIPTION
[1] Disassembly
•
STEP
REMOVAL
PRODCEDURE
FIGURE
1
Back Panel
1. Screw ................. (A1) X 6
1
2
Back Board
1. Screw ................. (B1) X 6
2
3
Speaker
1. Screw ............... (C1) X 12
3
4
Front Panel Ass’y
with PWB
with PWB
1. Screw ................. (D1) X 6
2. Screw ................. (D2) X 2
2. Screw ................. (D2) X 2
4
5
AMP Ass’y
1. Screw ................. (E1) X 2
2. Screw ................. (E2) X 2
2. Screw ................. (E2) X 2
2
5
5
6
Cross Over PWB
1. Screw ..................(F1) X 4
2. Socket .................(F2) X 2
2. Socket .................(F2) X 2
6
5, 7
7
Volume PWB
1. Knob................... (G1) X 1
2. Nut ..................... (G2) X 1
3. Washer...............(G3) X 1
4. Screw ................. (G4) X 2
5. Socket ................(G5) X 2
2. Nut ..................... (G2) X 1
3. Washer...............(G3) X 1
4. Screw ................. (G4) X 2
5. Socket ................(G5) X 2
7
7
7
6
7
7
7
6
7
8
LED PWB
1. Screw ................. (H1) X 1
7
9
Rear Panel with
Fan Ass’y
Fan Ass’y
1. Screw .................. (J1) X 6
2. Screw .................. (J2) X 4
3. Socket ................. (J3) X 1
2. Screw .................. (J2) X 4
3. Socket ................. (J3) X 1
8
8
9
8
9
10
Subwoofer PWB
1. Screw ................. (K1) X 4
2. Socket ................ (K2) X 3
2. Socket ................ (K2) X 3
9
9, 10
11
Main PWB
1. Screw ..................(L1) X 1
2. Socket .................(L2) X 2
2. Socket .................(L2) X 2
10
12
Power PWB
1. Screw .................(M1) X 8
10
Caution on disassembly
Follw the below-mentioned notes when
disassembling the unit and reassembling it, to keep
it safe and ensure excellent performance:
1) Be sure to remove the power supply plug from
Follw the below-mentioned notes when
disassembling the unit and reassembling it, to keep
it safe and ensure excellent performance:
1) Be sure to remove the power supply plug from
the wall outlet before starting to disassemble the
unit.
unit.
2) Take off nylon bands or wire holders where they
need to to removed when disassembling the unit.
After servicing the unit, be sure to rearrange the
leads where they were before disassembling.
After servicing the unit, be sure to rearrange the
leads where they were before disassembling.
3) Take sufficient care on static electricity of
integrated circuits and oher circuits when
servicing.
servicing.
CP-SW1000H
2 – 2
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Power PWB
Main PWB
AMP Ass’y
(F2)x1
From Cross Over PWB
(E2)x2
M3x15mm
M3x15mm
(G4)x2
Special Screw
Special Screw
(F1)x4
M3x10mm
M3x10mm
Cross Over PWB
Front Panel Ass’y with PWB
Volume PWB
Volume PWB
Cross Over PWB
(F2)x1
From Cross Over PWB
From Cross Over PWB
(G5)x1
From Subwoofer PWB
From Subwoofer PWB
(G5)x1
From LED PWB
From LED PWB
(H1)x1
M2.6x8mm
M2.6x8mm
(G1)x1
LED PWB
Front Panel Ass’y
(G2)x1
(G3)x1
(L2)x2
From Main PWB
From Subwoofer PWB
(L1)x1
M3x8mm
M3x8mm
(M1)x4
M3x8mm
M3x8mm
(M1)x4
M3x8mm
M3x8mm
(K1)x4
M3x8mm
M3x8mm
(J3)x1
From Fan Ass’y
From Fan Ass’y
(K2)x2
From Subwoofer PWB
Subwoofer PWB
(J2)x2
M3x6mm
M3x6mm
(J2)x2
M3x6mm
M3x6mm
(J1)x6
M3x8mm
M3x8mm
AMP Ass’y
Rear Panel with Fan Ass’y
