DOWNLOAD Sharp CD-XP110 Service Manual ↓ Size: 1.06 MB | Pages: 35 in PDF or view online for FREE

02/5/31

CD-XP110H(H)E2.fm

8

CD-XP110H

" Starting playback with a desired track

You can play a disc starting with the desired track.

Notes:
! When the DISC SKIP button is pressed during playback, the next

disc will begin automatically.

! When one of the   1 -   3 buttons on the remote control is

pressed during playback, the selected disc will begin automati-
cally.

! If you select a disc with the   1 -   3 buttons and a track with the

 / 

 or 

 / 

 button, a track number exceeding the total

track number on the disc may be displayed (maximum 99). In this
case, the last track on the selected disc is played back.

" Repeat play

All tracks on up to 3 discs, or a programmed sequence can be con-
tinuously repeated.

To cancel repeat play:
Press the   /   button again.
" " will go out.
 

" Random play

The tracks on the disc(s) can be played in random order automatically.

To cancel random play:
Press the RANDOM button.

! If you press the 

 

 button during random play, you can move

to the track selected next by the random operation. On the other
hand, the 

 

 button does not allow you to move to the previ-

ous track. The beginning of the track being played will be located.

! In random play, the CD player will select and play tracks auto-

matically. (You cannot select the order of the tracks.)

Caution:
After performing repeat or random play, be sure to press the   but-
ton. Otherwise, the disc(s) will play continuously.

Selected disc number

Selected track number

Playback of the selected track is started. When the end of last 
track of the disc selected is reached, the next disc will be auto-
matically started.

To repeat all tracks on up to 3 discs:
Press the   /   button twice.

To repeat a desired track:
Perform steps 1 - 4 in the "Programmed play" section on page 15 
and then press the   /   button twice.

02/5/31

CD-XP110H(H)E2.fm

CD-XP110H

" Programmed play

This may be operated only with the remote control.
You can choose up to 20 selections for playback in the order you
like.

Adding tracks to the programme:
If a programme has been previously stored, the "MEMORY" indica-
tor will be displayed. Then follow steps 1 - 3 to add tracks. The new
tracks will be stored after the last track of the original programme.

! If you open the disc tray, change to another function or enter the

stand-by mode, the programmed sequence is automatically can-
celled.

! During programme operation, random play is not possible.
 

" Care of compact discs

Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface. Follow
the guidelines below for maximum enjoyment from your CD collec-
tion and player.

! Do not write on either side of the disc, particularly the non-label

side from which signals are read. Do not mark this surface.

! Keep your discs away from direct sunlight, heat, and excessive

moisture.

! Always hold the CDs by the edges. Fingerprints, dirt, or water on

the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the centre, along the radius.

Selected disc number

Selected track number

If you select and memorise a track whose number exceeds the 
last track number on the disc, it will not be played back.

Playback order

When the track is memorised, "MEMORY" will appear.

If you make a mistake, the programmed tracks can be cleared 
by pressing the CLEAR button.

To clear the programmed selections:
Whilst the "MEMORY" indicator is lit, set the 
CD to the stop mode and then press the 
CLEAR button.
Each time the button is pressed, one track will 
be cleared, beginning with the last track pro-
grammed. When all the tracks are cleared, 
"MEMORY" will disappear.

02/5/31

CD-XP110H(H)E2.fm

8

CD-XP110H

 

!

To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST" indicator.

"

" " will appear when an FM broadcast is in stereo.

"

If the FM reception is weak, press the TUNER (BAND) button to
extinguish the "ST" indicator. The reception changes to monau-
ral, and the sound becomes clearer.

Press the TUNING button as many times as required to tune in 
to the desired station.

When the TUNING button is pressed for more than 0.5 sec-
onds, scanning will start automatically and the tuner will stop at 
the first receivable broadcast station.

 

"

When radio interference occurs, auto scan tuning may stop 
automatically at that point.

"

Auto scan tuning will skip weak signal stations.

"

To stop the auto tuning, press the TUNING button again.

FM stereo mode indicator

FM stereo receiving indicator

02/5/31

CD-XP110H(H)E2.fm

CD-XP110H

!

This may be operated only with the remote control.
You can store 30 AM and FM stations in memory and recall them at
the push of a button. (Preset tuning)
 

Note:
The backup function protects the memorised stations for a few
hours should there be a power failure or the AC power lead discon-
nection.
 

!

Store the stations in memory, in order, starting with preset 
channel 1.

If the preset number indicators go out before the station is 
memorised, repeat the operation from step 2.

When a new station is stored in memory, the station previously 
memorised will be erased.

"

"

Do not use C-120 tapes or poor-quality tapes, as 
they may cause malfunctions.

"

Before loading a tape into the cassette compartment, 
tighten the slack with a pen or a pencil.