Sharp CD-MPX860H User Manual / Operation Manual ▷ View online
CD-MPX860HE .fm
9
CD-MPX860H
Preparation for Use
System connections
Left speaker
Right speaker
Speaker connection
(see page 10)
(see page 10)
Aerial connection (see page 10)
Make sure to unplug the AC power lead before any connections.
FM aerial
AM loop aerial
AC power connection (see page 11)
Wall socket
(AC 230 V, 50 Hz)
CD-MPX860HE .fm
10
CD-MPX860H
Preparation for Use
System connections (continued)
Aerial connection
Note:
Placing the aerial on the unit or near the AC power lead may cause
noise pickup. Place the aerial away from the unit for better reception.
noise pickup. Place the aerial away from the unit for better reception.
Installing the AM loop aerial:
Speaker connection
Connect the black wire to the minus (-) terminal, and the red wire to
the plus (+) terminal.
the plus (+) terminal.
Caution:
Supplied FM aerial:
Connect the FM aerial wire to the FM
75 OHMS socket and position the FM
aerial wire in the direction where the
strongest signal can be received.
75 OHMS socket and position the FM
aerial wire in the direction where the
strongest signal can be received.
Supplied AM loop aerial:
Connect the AM loop aerial to the AM
and GND terminals. Position the AM
loop aerial for optimum reception.
Place the AM loop aerial on a shelf,
etc., or attach it to a stand or a wall with
screws (not supplied).
and GND terminals. Position the AM
loop aerial for optimum reception.
Place the AM loop aerial on a shelf,
etc., or attach it to a stand or a wall with
screws (not supplied).
< Assembling >
< Attaching to the wall >
Wall Screws (not supplied)
ANTENNA
FM
75 OHMS
AM
GND
AM loop
aerial
FM
aerial
Use speakers with an impedance of 6 ohms
or more, as lower impedance speakers can
damage the unit.
or more, as lower impedance speakers can
damage the unit.
Do not mistake the right and the left
channels. The right speaker is the one on the
right side when you face the unit.
channels. The right speaker is the one on the
right side when you face the unit.
Do not let the bare speaker wires touch
each other.
each other.
Do not stand or sit on the speakers. You may
be injured.
be injured.
Do not allow any objects to fall into or to be
placed in the bass reflex duct.
placed in the bass reflex duct.
Incorrect
Red
Black
CD-MPX860HE .fm
11
CD-MPX860H
Preparation for Use
AC power connection
After checking all the connections have been made correctly, plug
the AC power lead of this unit into the wall socket. If you plug in the
unit first, the unit will enter the demonstration mode.
the AC power lead of this unit into the wall socket. If you plug in the
unit first, the unit will enter the demonstration mode.
Notes:
The unit will start the tape initialisation when plugged into the wall
socket. During this process, initialising sound will be heard and
the unit cannot be turned on. Wait until the process is finished.
socket. During this process, initialising sound will be heard and
the unit cannot be turned on. Wait until the process is finished.
Unplug the AC power lead from the wall socket if the unit will not
be in use for a prolonged period of time.
be in use for a prolonged period of time.
Demonstration mode
External FM aerial
Use an external FM aerial if you require better reception. Consult
your dealer.
your dealer.
Note:
When an external FM aerial is used, disconnect the supplied FM
aerial wire.
When an external FM aerial is used, disconnect the supplied FM
aerial wire.
Cooling fan:
The main unit is built with a cooling fan at the rear of the unit for
improved cooling. Please do not cover the opening of the fan with
any obstacles, as this will block proper ventilation.
The main unit is built with a cooling fan at the rear of the unit for
improved cooling. Please do not cover the opening of the fan with
any obstacles, as this will block proper ventilation.
Wall socket
(AC 230 V, 50 Hz)
(AC 230 V, 50 Hz)
The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll.
unit will enter the demonstration mode.
You will see words scroll.
To cancel the demonstration mode:
When the unit is in the power
stand-by mode (demonstration
mode), press the X-BASS/DEMO
button. The unit will enter the low
power consumption mode.
When the unit is in the power
stand-by mode (demonstration
mode), press the X-BASS/DEMO
button. The unit will enter the low
power consumption mode.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/
DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to se-
lect the extra bass mode.
External
FM aerial
FM aerial
75 ohms
coaxial cable
coaxial cable
ANTENNA
FM
75 OHMS
AM
GND
CD-MPX860HE .fm
12
CD-MPX860H
Preparation for Use
Remote control
Battery installation
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to
malfunction.
Installing the batteries incorrectly may cause the unit to
malfunction.
Battery removal:
Open the battery cover and pull up the battery to take out.
Open the battery cover and pull up the battery to take out.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and
vibrations.
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control
Check the remote control after checking all the connections (see
pages 9 - 11).
Point the remote control directly at the remote sensor on the unit.
pages 9 - 11).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
Open the battery cover.
2
Insert the supplied batteries according to the direction indi-
cated in the battery compartment.
cated in the battery compartment.
When inserting or removing the batteries, push them towards the
battery terminals.
3
Close the battery cover.
Remote sensor
Click on the first or last page to see other CD-MPX860H service manuals if exist.