DOWNLOAD Sharp CD-DP2500 (serv.man3) Service Manual ↓ Size: 544.83 KB | Pages: 18 in PDF or view online for FREE

Model
CD-DP2500 (serv.man3)
Pages
18
Size
544.83 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Audio / System / Part 2
File
cd-dp2500-sm3.pdf
Date

Sharp CD-DP2500 (serv.man3) User Manual / Operation Manual ▷ View online

25
(Main unit operation)
(Continued)
EON-PTY
1
Tune in the desired RDS station (when a station name is
being displayed).
2
Press the EON button when “EON” appears.
“PTY TI” and “SELECT” will appear alternately for about
6 seconds.
3
Whilst they are being displayed, select the desired
programme type using the PRESET (
X
 or 
W
) button.
The selected programme type will flash.
4
Within 4 seconds, press the PTY.TI SEARCH button.
The selected programme type and “WAITING” will be dis-
played for 2 seconds each.
“PTY” will appear, and the unit will enter the EON-PTY
stand-by mode.
5
When a programme of the type specified starts on an ON
(other network) station, the unit will automatically switch to
the station broadcasting the selected programme type, and
“PTY” will flash.
6
When the programme specified for the ON station is over,
the unit will automatically return to the original station you
were tuned to.
Note:
If the EON button is pressed when “EON” is not displayed,
“NO EON” will appear for 5 seconds to indicate that the unit
cannot enter the EON stand-by mode.
Checking the stand-by mode setting:
When in the EON stand-by mode, press the EON button.
(“Programme type” 
 “WAITING”)
To cancel the EON stand-by mode:
When in the EON stand-by mode, press the EON button. Within
4 seconds, press it again. The EON stand-by mode will be can-
celled.
“PTY” will go out.
About the PTYI (Dynamic PTY Indicator):
PTYI (Dynamic PTY Indicator) will appear whilst the Dynamic
PTY station is being received.
Dynamic PTY indicates that the PTY for the station tuned in, or
the PTY referenced in the EON data, is assessed whenever
the programme changes and may be changed.
PTYI
Meaning
Lights up
Tuned into a dynamic PTY station.
Goes out
Tuned into a static PTY.
Note:
When “PTYI” appears, if you press the DISPLAY MODE but-
ton to display the programme type, you can check the type
of programme you are actually receiving.
26
(Main unit operation)
(Continued)
About the TP and TA indicators
TP indicator
TA indicator
Meaning
Not lit
Not lit
This programme does not carry traffic announcements nor
does it refer, via EON, to a programme that does.
Not lit
Lit
This programme carries EON information about another
programme which gives traffic information.
Lit
Not lit
This programme carries traffic announcements but none
are being broadcast at present and may also carry EON
information about other traffic announcements.
Lit
Lit
A traffic announcement is being broadcast on this
programme at present.
EON-TI
1
Tune in the desired RDS station (when a station name is
being displayed).
2
Press the EON button when “EON” appears.
“PTY TI” and “SELECT” will appear alternately for about
6 seconds.
3
Whilst they are being displayed, select the TI (Traffic Infor-
mation) using the PRESET (
X
 or 
W
) button.
The selected “TI” will flash.
4
Within 4 seconds, press the PTY.TI SEARCH button.
“TI” and “WAITING” will appear for 2 seconds each.
“TI” will appear, and the unit will enter the EON-TI stand-
by mode.
5
When a TA specifed starts on an ON (other network) sta-
tion, the unit will automatically switch to that station, and
“TI” will flash.
6
When the traffic announcement is over, the unit will auto-
matically return to the original station you were tuned to.
Note:
If the EON button is pressed when “EON” is not displayed,
“NO EON” will appear for 5 seconds to indicate that the unit
cannot enter the EON stand-by mode.
Checking the stand-by mode setting:
When in the EON stand-by mode, press the EON button.
(“TI” 
 “WAITING”)
To cancel the EON stand-by mode:
When in the EON stand-by mode, press the EON button. Within
4 seconds, press it again. The EON stand-by mode will be can-
celled.
“TI” will go out.
Note:
If neither “TP” nor “TA” appear, then even if “EON” appears
the unit cannot enter the EON-TI stand-by mode. In this
condition, if the PTY.TI SEARCH button is pressed after TI
is selected, “NO TI” will flash for 4 seconds.
27
(Continued)
In the following cases, the EON stand-by mode will be can-
celled.
When the unit is set in the stand-by mode
When the unit is switched to another band in the EON stand-
by mode
When you change the FM station whilst in the EON stand-
by mode
When a preset call is made
Notes:
During the same programme as the specified PTY (or TA) is
being broadcast on the station you are receiving, the unit
will not switch to other network station.
If there are more than two other network stations you want
to listen to, compare the strength of each station’s signal
and tune in the station with the strongest signal. (EON-AF)
However, if the frequency of other network station has been
stored in the preset channel memory, the unit will switch to
that preset channel.
If you want to cancel the reception of an ON (other network)
station which was tuned in by the EON system and return to
the original station you were receiving, press the EON but-
ton.
After the unit returns to the original station, the stand-by
mode will still be active. (The “TI” or “PTY” will remain lit.)
The unit will not switch from the ON station to another net-
work station. The unit returns to the original station.
When the unit switches automatically to “other network” sta-
tion, if there is any problem with this station or the station
cannot be received properly “WEAK SIG” will appear and
the unit will return to the original station.
Even if the unit switches from the station you are listening to
directly to some “other network” station, if the signals from
the other network stations are very weak, the unit will search
for the station with the strongest signal and switch to it.
However, if the signals from all the other network stations
are very weak, or if the tuning conditions are very bad (due
to electrical noise), the unit will stop searching, “WEAK SIG”
will be displayed, and the unit will return to the original sta-
tion you were receiving.
CASSETTE OPERATION
TAPE 1 or TAPE 2 playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TAPE (1 
V
 2) button.
3
Open the cassette door by pushing the area marked “PUSH
EJECT”.
4
Load the cassette into the TAPE 1 or TAPE 2 cassette com-
partment.
5
With cassettes in both decks, press the TAPE (1 
V
 2) button
to switch operation from one deck to the other.
6
Press the 
0
/
R
 button to start playback.
When playback is performed using the remote control,
press the TAPE 1 or TAPE 2 
0
 button.
To stop playback:
Press the 
 (TAPE 
) button.
Fast forward/rewind: (TAPE 2 only)
 1 Press the 
 (TAPE 
) button, then press the TAPE (1 
V
 2)
button to select TAPE 2.
 2 To advance the tape, press the 
2
 button.
To rewind it, press the 
3
 button.
Caution:
To remove the cassette tape, press the 
 (TAPE 
) button,
and then open the cassette compartment.
Before changing from one tape operation to another, press
the 
 (TAPE 
) button.
If a power failure occurs during tape operation, the tape head
will remain engaged with the tape and the cassette door will
not open. In this case, wait until power is restored.
28
RECORDING
When recording important selections, be sure to make a
preliminary test to ensure that the desired material is being
properly recorded.
The volume and sound quality can be adjusted with no ef-
fect on the recorded signals (Variable Sound Monitor).
Recording from the built-in CD player
(CD Synchronised Recording System)
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button and load the desired disc.
Use the APMS function to store the tracks you want to
record in memory. (See page 16.)
3
Load a cassette into the TAPE 2 cassette compartment.
4
Press the REC PAUSE (
 
6
) button.
“SYNC” and “REC” will flash.
5
Press the 
0
/
R
 (TAPE 2 
0
) button.
“SYNC” will disappear and “REC” will light up.
CD playback will start approximately 5 seconds after the
tape starts.
To stop recording:
Press the 
 (CD 
) button.
The CD and tape will stop.
Note:
When the end of the tape is reached whilst recording, the
CD player will display the track number which was being
played at that time, and stop automatically.
If you want to restart recording from the beginning of the
interrupted track, turn over the tape, press the REC PAUSE
(
 
6
) button and then the 
0
/
R
  (TAPE 2 
0
) button.
(If tracks have been stored in memory using the APMS func-
tion, recording will restart from the first track stored in
memory.)
Metal and CrO
2
 tapes should not be used for recording or
dubbing.
Page of 18
Display

Click on the first or last page to see other CD-DP2500 (serv.man3) service manuals if exist.