DOWNLOAD Sharp CD-DP2400H Service Manual ↓ Size: 1.65 MB | Pages: 32 in PDF or view online for FREE

Model
CD-DP2400H
Pages
32
Size
1.65 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Audio / System
File
cd-dp2400h.pdf
Date

Sharp CD-DP2400H User Manual / Operation Manual ▷ View online

24
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
 F
e
atures
- Time
r a
n
d
 s
le
e
p op
e
ra
tion -
Timer and sleep operation
Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at the preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset time.
Sleep operation:
The radio, compact disc and cassette tape can all be turned off automatically.
"
Timer playback or timer recording
Before setting timer:
1
Press the CLOCK button to check that the clock is on time.
2
For timer playback:
Load a cassette or discs to be played.
For timer recording:
Load a cassette for recording in the TAPE 2 cassette 
compartment.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD, TUNER (BAND) or TAPE (1   2) button to select the
desired function.
To select the timer playback source: CD, TUNER (BAND) or TAPE (1   2).
To select the timer recording source: TUNER (BAND).
When you selected the TUNER (BAND), tune in to the desired sta-
tion.
3
Adjust the volume using the VOLUME control.
Do not turn the volume up too high.
4
Press the TIMER/SLEEP button repeatedly until "  PLAY" or "
REC" is displayed.
For timer playback
For timer recording
5
Press the TUNING/TIME (  or  ) button to specify the hour to start,
then press the MEMORY/SET button.
The illustrations show the timer playback setting.
Web-site: www.sharp.co.uk/support    Help Line: 08705 274277 (office hours)
25
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
 F
e
atures
- Time
r a
n
d
 s
le
e
p op
e
ra
tion -
 
To reset or change the timer setting:
Perform "Timer playback or timer recording" from the beginning.
Notes:
"
Sleep operation
To cancel the sleep operation:
Press the ON/STAND-BY button whilst the sleep timer is set.
To confirm the remaining sleep time:
Press the TIMER/SLEEP button whilst the sleep timer is set.
The remaining sleep time is displayed for about 5 seconds.
Note:
Once the sleep time is set, it will remain unchanged until a new time is entered.
6
Press the TUNING/TIME (  or  ) button to specify the minutes,
then press the MEMORY/SET button.
7
The unit will enter the timer stand-by mode automatically.
To cancel the timer playback/timer recording:
Press the ON/STAND-BY button to turn the power on.
8
When the preset time is reached, playback or recording will start.
The volume will increase gradually until it reaches the volume you were listening 
at before your system enters the timer stand-by mode.
9
In timer playback:
If you select CD or TAPE, the unit will enter the stand-by mode after the play-
back. If you select TUNER, it will enter the stand-by mode one hour after the tim-
er playback starts.
In timer recording:
When the recording tape reaches its end, the timer recording will end, and the 
unit will enter the stand-by mode.
!
Once the time is set, the setting will be retained until a new time is entered.
!
When performing timer playback or recording using another unit connected to the 
VIDEO/AUX sockets, select "VIDEO/AUX" in step 2.
At this time, only this unit will be turned on or enter the power stand-by mode auto-
matically. It will enter the power stand-by mode when the end of the recording tape 
is reached in timer recording or 1 hour after the playback starts in timer playback. 
However, another unit will not be turned on or off.
1
Play back the desired sound source.
2
Press the TIMER/SLEEP button repeatedly until "SLEEP" is dis-
played.
To change the sleep time:
Whilst the sleep time is displayed, press the TUNING/TIME (  or  ) button.
(Maximum: 3 hours - Minimum: 1 minute)
!
3 hours - 5 minutes   5-minute intervals
!
5 minutes - 1 minute   1-minute intervals
3
Press the MEMORY/SET button.
4
Your system will enter the power stand-by mode automatically af-
ter the preset time has elapsed.
The volume will be turned down 1 minute before the sleep operation finishes.
Web-site: www.sharp.co.uk/support    Help Line: 08705 274277 (office hours)
26
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
 F
e
atures
- Enha
nc
ing y
our
 s
y
s
te
m
 -
Enhancing your system
The connection lead is not included. Purchase a commercially available lead as
shown below.
!
Listening to the playback sounds from 
VCR, DVD, etc.
Note:
To prevent hum interference, place this unit away from a television.
 
 
!
To record on a tape
 
 
!
Headphones
"
Before plugging in or unplugging the headphones, reduce the volume.
"
Be sure your headphones have a 3.5 mm (1/8") diameter plug and are between 16
ohms and 50 ohms impedance. The recommended impedance is 32 ohms.
"
Plugging in the headphones disconnects the speakers automatically. Adjust the
volume using the VOLUME control.
VCR, DVD, etc.
To the 
line output 
sockets
Red
RCA lead
(not supplied)
White
Red
White
1
Use a connection lead to connect the VCR, DVD, etc. to the VIDEO/
AUX sockets.
When using video equipment, connect the audio output to this unit and the video 
output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the VIDEO/AUX button.
4
Play the connected equipment.
1
Insert a cassette in the TAPE 2 cassette compartment.
2
Press the VIDEO/AUX button.
3
Press the REC/PAUSE (
) button.
4
Press the   /   (TAPE 2  ) button.
5
Play the VCR, DVD, etc.
Web-site: www.sharp.co.uk/support    Help Line: 08705 274277 (office hours)
27
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
 F
e
atures
- Enjo
y
 the
 s
u
rr
ound s
o
und -
Enjoy the surround sound  
!
Dolby Pro Logic Surround (Normal or 
Phantom) mode
By connecting this unit to other equipment (DVD player, VCR, etc.) with the
 trademark and playing it, you can enjoy Dolby Pro Logic Surround
sound.
To listen in the normal or phantom mode:
 
To cancel the Dolby Pro Logic Surround mode:
Press the DOLBY PRO LOGIC button on the remote control until "BYPASS" appears,
or press the BYPASS button on the main unit.
Notes:
"
If the EQ (EQUALIZER MODE) button is pressed in the normal or phantom mode,
the unit is switched to the bypass mode automatically. 
"
When in the normal or phantom mode, the sound mode will be set to FLAT.
"
You cannot use the Dolby Pro Logic Surround feature with headphones.
"
The selected Dolby Pro Logic Surround mode is automatically stored in memory
and will be used the next time you activate Dolby Pro Logic. This mode is memo-
rised until a new mode is selected.
Centre speaker
Normal mode:
Phantom mode:
Front speaker (Left)
Front speaker (Right)
Surround speaker (Right)
Surround speaker (Left)
Front speaker (Left)
Front speaker (Right)
Surround speaker (Right)
Surround speaker (Left)
1
Connect the equipment you want to play (see page 26). 
2
Press the VIDEO/AUX button.
3
Press the DOLBY PRO LOGIC button on the remote control to se-
lect the Dolby Pro Logic Surround mode.
Each time you press the button, the display will change as follows:
NORMAL:
Sound will be output from the front left, front right, centre, and sur-
round speakers.
PHANTOM:
Unlike the normal mode, no sound is output from the centre 
speaker. The centre speaker signal is split equally and added to 
the sound from the front speakers. 
BYPASS:
The Dolby Pro Logic Surround mode is cancelled. Sound will only 
be output from the front speakers.
"
You can select the desired surround mode by pressing the NORMAL or 
PHANTOM button on the main unit.
4
Start playing the sound source.
NORMAL
PHANTOM
BYPASS
Web-site: www.sharp.co.uk/support    Help Line: 08705 274277 (office hours)
Page of 32
Display

Click on the first or last page to see other CD-DP2400H service manuals if exist.