Sharp CD-DP2400H User Manual / Operation Manual ▷ View online
23
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
T
a
p
e
Recor
d
in
g
- Rec
o
rd
in
g
t
o
a ca
sse
tt
e
ta
p
e
-
"
Recording from the radio
To interrupt recording:
Press the REC/PAUSE (
) button.
To resume recording, press the / (TAPE 2 ) button.
To stop recording:
Press
the
(TAPE )
button.
Note:
If you hear a whistling noise whilst recording an AM station, move the AM loop aerial.
"
Dubbing from tape to tape
You can record from TAPE 1 to TAPE 2.
To stop dubbing:
Press
the
(TAPE )
button.
TAPE 1 and TAPE 2 will simultaneously stop.
"
Erasing recorded tapes
Note:
Make sure that the TAPE 1 is not in use.
1
Tune in to the desired station. (See page 19.)
2
Load a cassette into the TAPE 2 cassette compartment with the
side to be recorded on facing you.
side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be performed.
3
Press the REC/PAUSE (
)
button.
Recording will be paused.
4
Press the / button on the
main unit or the TAPE 2 but-
ton on the remote control to
start recording.
main unit or the TAPE 2 but-
ton on the remote control to
start recording.
Erase-prevention tab of cassette tapes:
!
When recording on a cassette tape, make
sure that the erase-prevention tabs are not
removed. Cassettes have removable tabs
that prevent accidental recording or erasing.
sure that the erase-prevention tabs are not
removed. Cassettes have removable tabs
that prevent accidental recording or erasing.
!
To protect the recorded sound, remove the
tab after recording. Cover the tab hole with
adhesive tape to record on the tape without
the tab.
tab after recording. Cover the tab hole with
adhesive tape to record on the tape without
the tab.
Tab of side B
Tab of side A
Side A
1
Press the ON/STAND-BY button to turn the power on.
2
Load a prerecorded cassette into
the TAPE 1 cassette compart-
ment. Insert a blank tape into the
TAPE 2 cassette compartment.
the TAPE 1 cassette compart-
ment. Insert a blank tape into the
TAPE 2 cassette compartment.
It is recommended that the recording
tape is the same length as the master
tape.
tape is the same length as the master
tape.
3
Press the TAPE (1 2) button un-
til "TAPE 1" appears on the dis-
play.
til "TAPE 1" appears on the dis-
play.
4
Press the REC/PAUSE (
) but-
ton.
Recording will be paused.
5
Press the / button on the
main unit or the TAPE 2 button
on the remote control to start
dubbing.
main unit or the TAPE 2 button
on the remote control to start
dubbing.
1
Load the tape to be erased into the TAPE 2 cassette compartment with the side to
be erased facing toward you.
be erased facing toward you.
2
Press the TAPE (1 2) button until "TAPE 2" appears on the display.
3
Press the REC/PAUSE (
) button.
4
Press the / button on the main unit or the TAPE 2 button on the remote con-
trol to start erasing.
trol to start erasing.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
24
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
F
e
atures
- Time
r a
n
d
s
le
e
p op
e
ra
tion -
Timer and sleep operation
Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at the preset time.
The unit turns on and plays the desired source (CD, tuner, tape) at the preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset time.
The unit turns on and starts recording from the tuner at the preset time.
Sleep operation:
The radio, compact disc and cassette tape can all be turned off automatically.
The radio, compact disc and cassette tape can all be turned off automatically.
"
Timer playback or timer recording
Before setting timer:
1
Press the CLOCK button to check that the clock is on time.
2
For timer playback:
Load a cassette or discs to be played.
For timer recording:
Load a cassette for recording in the TAPE 2 cassette
compartment.
compartment.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD, TUNER (BAND) or TAPE (1 2) button to select the
desired function.
desired function.
To select the timer playback source: CD, TUNER (BAND) or TAPE (1 2).
To select the timer recording source: TUNER (BAND).
When you selected the TUNER (BAND), tune in to the desired sta-
tion.
tion.
3
Adjust the volume using the VOLUME control.
Do not turn the volume up too high.
4
Press the TIMER/SLEEP button repeatedly until " PLAY" or "
REC" is displayed.
REC" is displayed.
For timer playback
For timer recording
5
Press the TUNING/TIME ( or ) button to specify the hour to start,
then press the MEMORY/SET button.
then press the MEMORY/SET button.
The illustrations show the timer playback setting.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
25
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
F
e
atures
- Time
r a
n
d
s
le
e
p op
e
ra
tion -
To reset or change the timer setting:
Perform "Timer playback or timer recording" from the beginning.
Notes:
"
Sleep operation
To cancel the sleep operation:
Press the ON/STAND-BY button whilst the sleep timer is set.
To confirm the remaining sleep time:
Press the TIMER/SLEEP button whilst the sleep timer is set.
The remaining sleep time is displayed for about 5 seconds.
The remaining sleep time is displayed for about 5 seconds.
Note:
Once the sleep time is set, it will remain unchanged until a new time is entered.
6
Press the TUNING/TIME ( or ) button to specify the minutes,
then press the MEMORY/SET button.
then press the MEMORY/SET button.
7
The unit will enter the timer stand-by mode automatically.
To cancel the timer playback/timer recording:
Press the ON/STAND-BY button to turn the power on.
8
When the preset time is reached, playback or recording will start.
The volume will increase gradually until it reaches the volume you were listening
at before your system enters the timer stand-by mode.
at before your system enters the timer stand-by mode.
9
In timer playback:
If you select CD or TAPE, the unit will enter the stand-by mode after the play-
back. If you select TUNER, it will enter the stand-by mode one hour after the tim-
er playback starts.
back. If you select TUNER, it will enter the stand-by mode one hour after the tim-
er playback starts.
In timer recording:
When the recording tape reaches its end, the timer recording will end, and the
unit will enter the stand-by mode.
unit will enter the stand-by mode.
!
Once the time is set, the setting will be retained until a new time is entered.
!
When performing timer playback or recording using another unit connected to the
VIDEO/AUX sockets, select "VIDEO/AUX" in step 2.
At this time, only this unit will be turned on or enter the power stand-by mode auto-
matically. It will enter the power stand-by mode when the end of the recording tape
is reached in timer recording or 1 hour after the playback starts in timer playback.
However, another unit will not be turned on or off.
VIDEO/AUX sockets, select "VIDEO/AUX" in step 2.
At this time, only this unit will be turned on or enter the power stand-by mode auto-
matically. It will enter the power stand-by mode when the end of the recording tape
is reached in timer recording or 1 hour after the playback starts in timer playback.
However, another unit will not be turned on or off.
1
Play back the desired sound source.
2
Press the TIMER/SLEEP button repeatedly until "SLEEP" is dis-
played.
played.
To change the sleep time:
Whilst the sleep time is displayed, press the TUNING/TIME ( or ) button.
(Maximum: 3 hours - Minimum: 1 minute)
!
3 hours - 5 minutes 5-minute intervals
!
5 minutes - 1 minute 1-minute intervals
3
Press the MEMORY/SET button.
4
Your system will enter the power stand-by mode automatically af-
ter the preset time has elapsed.
ter the preset time has elapsed.
The volume will be turned down 1 minute before the sleep operation finishes.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
26
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
F
e
atures
- Enha
nc
ing y
our
s
y
s
te
m
-
Enhancing your system
The connection lead is not included. Purchase a commercially available lead as
shown below.
shown below.
!
Listening to the playback sounds from
VCR, DVD, etc.
VCR, DVD, etc.
Note:
To prevent hum interference, place this unit away from a television.
!
To record on a tape
!
Headphones
"
Before plugging in or unplugging the headphones, reduce the volume.
"
Be sure your headphones have a 3.5 mm (1/8") diameter plug and are between 16
ohms and 50 ohms impedance. The recommended impedance is 32 ohms.
ohms and 50 ohms impedance. The recommended impedance is 32 ohms.
"
Plugging in the headphones disconnects the speakers automatically. Adjust the
volume using the VOLUME control.
volume using the VOLUME control.
VCR, DVD, etc.
To the
line output
sockets
line output
sockets
Red
RCA lead
(not supplied)
(not supplied)
White
Red
White
1
Use a connection lead to connect the VCR, DVD, etc. to the VIDEO/
AUX sockets.
AUX sockets.
When using video equipment, connect the audio output to this unit and the video
output to a television.
output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the VIDEO/AUX button.
4
Play the connected equipment.
1
Insert a cassette in the TAPE 2 cassette compartment.
2
Press the VIDEO/AUX button.
3
Press the REC/PAUSE (
) button.
4
Press the / (TAPE 2 ) button.
5
Play the VCR, DVD, etc.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Click on the first or last page to see other CD-DP2400H service manuals if exist.