Sharp CD-DP2400H User Manual / Operation Manual ▷ View online
14
CD-DP2400H(E)2.fm
01/7/17
CD-DP2400H
B
asic Ope
ration
-
S
e
tting the
c
loc
k
-
Setting the clock
In this example, the clock is set for the 24-hour (0:00) display.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from the beginning. If the time display is flashing, step 3
(for selecting the 24-hour or 12-hour display) will be skipped.
(for selecting the 24-hour or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK button and within 5 seconds, press the MEMO-
RY/SET button.
RY/SET button.
3
Press the TUNING/TIME ( or ) button to select 24-hour or 12-
hour display and then press the MEMORY/SET button.
hour display and then press the MEMORY/SET button.
"0:00"
The 24-hour display will appear.
(0:00 - 23:59)
"AM 12:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00"
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it has been reset.
[Refer to "Clearing all the memory (reset)" on page 30 for details.]
[Refer to "Clearing all the memory (reset)" on page 30 for details.]
4
Press the TUNING/TIME ( or ) button to adjust the hour and then
press the MEMORY/SET button.
press the MEMORY/SET button.
"
Press the TUNING/TIME ( or ) button once to advance the time by 1 hour.
Hold it down to advance continuously.
Hold it down to advance continuously.
"
When the 12-hour display is selected, "AM" will change automatically to "PM".
5
Press the TUNING/TIME ( or ) button to adjust the minutes and
then press the MEMORY/SET button.
then press the MEMORY/SET button.
"
Press the TUNING/TIME ( or ) button once to advance the time by 1
minute. Hold it down to change the time in 5-minute intervals.
minute. Hold it down to change the time in 5-minute intervals.
"
The hour will not advance even if minutes advance from "59" to "00".
"
The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
The time display will disappear after a few seconds.
To confirm the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
The time display will appear for about 5 seconds.
1
Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on
page 30 for details.]
page 30 for details.]
2
Perform "Setting the clock" from the beginning.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
15
CD-DP2400H(E)2.fm
01/7/17
CD-DP2400H
CD Pla
y
ba
c
k
- L
ist
en
in
g
t
o
a CD
(
C
Ds)
-
Listening to a CD (CDs)
Continued to the next page
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray.
4
Place the CD(s) on the disc tray, label side up.
When loading a third disc, press the DISC SKIP button to turn the
disc tray, then place the CD in the open position.
disc tray, then place the CD in the open position.
"
CDs can be placed on any open position on the disc tray.
"
Be sure to place 8 cm (3") CD(s) in the middle of the disc positions.
5
Press the OPEN/CLOSE button to close the disc tray.
Music schedule
Total number of tracks on the
CD whose number is flashing
CD whose number is flashing
Total playing time of the CD whose
number is flashing
number is flashing
The music schedule will display only the number of tracks on the disc.
If the CD contains more than 15 tracks, "
" will appear.
6
To select the CD you want to listen to first, press one of the DISC-
1 - DISC-3 buttons.
1 - DISC-3 buttons.
12 cm (5")
8 cm (3")
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
16
CD-DP2400H(E)2.fm
01/7/17
CD-DP2400H
CD Pla
y
ba
c
k
- L
ist
en
in
g
t
o
a CD
(
C
Ds)
-
Listening to a CD (CDs) (continued)
To interrupt playback:
Press the CD button on the remote control.
To resume playback from the same point, press the button.
To resume playback from the same point, press the button.
To stop playback:
Press
the
(CD )
button.
To remove the CDs:
Whilst in the stop mode, press the OPEN/CLOSE button.
The disc tray will open. Remove the two discs. Then, press the DISC SKIP button to
rotate the disc tray and remove the remaining disc.
The disc tray will open. Remove the two discs. Then, press the DISC SKIP button to
rotate the disc tray and remove the remaining disc.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
Caution:
!
Do not place two CDs in one disc tray.
!
Do not push the disc tray whilst it is moving.
!
Do not turn the disc tray by hand. This may cause malfunctions.
!
If the power fails whilst the tray is open, wait until the power is restored.
!
If the disc tray is stopped forcibly, "ERR 0203" will appear in the display and the
unit will not function. If this occurs, press the ON/STAND-BY button to enter the
power stand-by mode and then turn the power on again.
unit will not function. If this occurs, press the ON/STAND-BY button to enter the
power stand-by mode and then turn the power on again.
!
If TV or radio interference occurs during CD operation, move the unit away from
the TV or radio.
the TV or radio.
!
If a disc is damaged, dirty, or loaded upside down, the disc will be skipped.
"
To locate the beginning of a track
Notes:
!
You can locate the beginning of a track on a single disc only.
!
The
/
or
/
button on the remote control allows you to locate the
beginning of a track.
"
To locate the desired portion
Notes:
!
Normal playback will resume when the
or
button is released.
!
You can locate the desired portion on a single disc only.
!
When the end of the last track is reached during fast forward, "END" will appear on
the display and CD operation will be paused. When the beginning of the first track
is reached during fast reverse, the unit will enter the playback mode.
the display and CD operation will be paused. When the beginning of the first track
is reached during fast reverse, the unit will enter the playback mode.
!
The
/
or
/
button on the remote control allows you to locate the
desired portion.
7
Press the / ( ) button to start playback.
!
Playback will begin from track 1 on the disc you have selected to play. After
that disc finishes playing, the next disc will automatically start playback.
that disc finishes playing, the next disc will automatically start playback.
!
When the last track on the third disc has finished playing, the CD player will
stop automatically.
stop automatically.
!
When there is no CD in one of the disc 1 - 3 positions, that position will be
skipped and the next CD will be played.
skipped and the next CD will be played.
To move to the beginning of the next track:
Press the
button for less than 0.5 seconds during playback.
!
You can skip to any track by pressing the
button repeatedly until the desired track
number appears.
To restart the track being played:
Press the
button for less than 0.5 seconds during playback.
!
You can skip to any track by pressing the
button repeatedly until the desired track
number appears.
For audible fast forward:
Press and hold down the
button during playback.
For audible fast reverse:
Press and hold down the
button during playback.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
17
CD-DP2400H(E)2.fm
01/7/17
CD-DP2400H
CD Pla
y
ba
c
k
- Lis
te
n
ing to a
CD
(
C
Ds
) / Re
pe
a
t or
r
a
ndom pla
y
-
"
Starting Playback with a Desired Track
You can play a disc starting with the desired track.
To stop playback:
Press the (CD ) button.
Notes:
!
When the DISC SKIP button is pressed during playback, the next disc will begin
automatically.
automatically.
!
When one of the DISC-1 - DISC-3 buttons is pressed during playback, the
selected disc will begin automatically.
selected disc will begin automatically.
Repeat or random play
"
Repeat play
All tracks on up to 3 discs, or a programmed sequence can be continuously repeated.
To repeat a desired track:
Perform steps 1 - 4 in the "Programmed play" section and then press the / ( )
button twice.
button twice.
To cancel repeat play:
Press the / ( ) button again.
" " will go out.
" " will go out.
"
Random play
The tracks on the disc(s) can be played in random order automatically.
To cancel random play:
Press the button.
Notes:
!
If you press the
/
button during random play, you can move to the track
selected next by the random operation. On the other hand, the
/
button
does not allow you to move to the previous track. The beginning of the track being
played will be located.
played will be located.
!
In random play, the CD player will select and play tracks automatically. (You cannot
select the order of the tracks.)
select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the (CD ) button. Other-
wise, the disc(s) will play continuously.
wise, the disc(s) will play continuously.
1
Whilst in the stop mode, press one of the DISC-1 - DISC-3 but-
tons or DISC SKIP button to select the desired disc.
tons or DISC SKIP button to select the desired disc.
Selected disc number
2
Press the
or
button to select the desired track.
Selected track number
You can also select a track by pressing the
/
or
/
button on the
remote control.
3
Press the / ( ) button to start playback.
Playback of the selected track is started. When the end of last track of the
disc selected is reached, the next disc will be automatically started.
disc selected is reached, the next disc will be automatically started.
To repeat all tracks on up to 3 discs:
Press the / ( ) button twice.
Press the RANDOM button on the remote control to begin random
play.
play.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Click on the first or last page to see other CD-DP2400H service manuals if exist.