Sharp CD-C621H User Manual / Operation Manual ▷ View online
CD-C621H
– 6 –
OPERATION MANUAL
TUNING/
TIME
( )
MEMORY/
SET
CLOCK
ON/
STAND-BY
SETTING THE CLOCK
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press
the
TUNING/TIME
(
or
) button to select the time
display mode.
"0:00"
→
T
h
e
24
-h
o
u
r d
isp
la
y w
ill
ap
pe
ar
.
(
0
:0
0
-
2
3
:5
9
)
"AM 12:00"
→
T
h
e 1
2
-h
ou
r di
sp
la
y
w
ill
ap
pe
ar
.
(
A
M
o
r P
M
1
2
:0
0
-
1
1
:5
9
)
"A
M
0:
00
"
→
Th
e 1
2
-h
ou
r di
sp
lay
w
ill
ap
pe
ar
.
(
A
M
o
r P
M
0
:0
0
-
1
1
:5
9
)
Note that this can only be set when the unit is first installed
or it has been reset.
5
Press the MEMORY/SET button.
6
Press
the
TUNING/TIME
(
or
) button to adjust the hour.
Press the TUNING/TIME (
or
) button once to advance
the time by 1 hour. Hold it down to advance continuously.
When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
7
Press the MEMORY/SET button.
8
P
re
s
s
th
e
TU
N
IN
G
/TI
M
E
(
o
r
) b
u
tt
o
n
to
a
d
ju
s
t
th
e
minutes.
Press the TUNING/TIME (
or
) button once to advance
the time by 1 minute. Hold it down to change the time in 5
minute intervals.
The hour setting will not advance even if minutes advance from
"59" to "00".
9
Press the MEMORY/SET button.
The clock starts operating from "0" seconds. (Seconds are not
displayed.)
Note:
In the event of a power failure or when the AC power lead is
disconnected, the clock display will go out.
flash on and off to indicate the time when the power failure
occurred or when the AC power lead was disconnected.
If this happens, follow the procedure below to change the clock
time.
To change the clock time:
Press the CLOCK button.
Within 5 seconds, press the MEMORY/SET button.
Perform steps 6 - 9 above.
To see the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
To change the time display mode:
Perform steps 1 - 2 in the section "RESETTING THE MICRO-
COMPUTER".
Perform steps 1 - 9 above.
(Main unit operation)
In this example, the clock is set for the
AM 12:00
AM 0:00
0:00
2
3
4
7
6
5
8
9
1
2
1
2
3
2
1,2
RESETTING THE MICROCOMPUTER
PREPARATION FOR USE
Reset the microcomputer under the following conditions:
settings, and tuner and CD presets).
If the display is not correct.
If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Whilst pressing down the
button and the
button, hold down the ON/STAND-BY button for at least 1
second.
Caution:
memory including clock and timer settings, and tuner and CD
presets.
15
15
Notes concerning use:
Replace the batteries if the operating distance is reduced or if
the operation becomes erratic.
Periodically clean the transmitter LED on the remote control
and the sensor on the main unit with a soft cloth.
Exposing the sensor on the main unit to strong light may in-
terfere with operation. Change the lighting or the direction of
the unit.
Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
0.2 m - 6 m
(8" - 20')
Display