Sharp CD-C5H Service Manual ▷ View online
CD-C5H,CP-C5H
– 17 –
No
ASPM, summary operation
Hold down the
ASPM button for 3 more second.
“ASPM” blinks in the display
.
Preset CH memory full over?
No operate.
After displayed “END”. Return to
previous station.
SD (TUNE) DET out OK?
If count 1st OK?
If count 2nd OK?
RDS signal or not? PI—identify
Comparing PI cord same or not?
between current receiving PI and
before PI which is already memorized
by
ASPM on this time.
Comparing freg. same or not?
between current receiving frequency
and (already) previously memorized
frequency
.
Memorized to the lowest
vacant preset channel.
Preset CH memory become full over?
Begin to
ASPM SCAN from the next
CH-SP
AN again.
Repeat and continue with same format
ASPM operation untill 108 MHz.
After reached 108 MHz, displayed the
TTL quantity of memorized stations.
And return to the previous receiving
freq. automatically
.
Displayed the
TTL
quantity of memo-
rized stations by
ASPM operation on
this time.
And return to the previous
receiving freq. automatically
.
Ye
s
No
Ye
s
Ye
s
Ye
s
Ye
s
No
No
No
No
No
No
Ef
fect
Pass
No ef
fect
Pass
No ef
fect
Pass
No ef
fect
Pass
No ef
fect
Ye
s
No
Ye
s
Compare the field strength of current
receiving signal. Is receiving signal
stronger than signal which has same PI
cord and is already memorized to
preset memory ahead of this receiving
time?
Ye
s
No ef
fect
No
No ef
fect
Comparing freg. same or not?
Between current receiving frequency
and (already) previously memorized
frequency
.
Ye
s
Memorized to the lowest
vacant preset channel.
Ye
s
No ef
fect
Begin to scan start 87.50
→
108.00 MHz
CD-C5H,CP-C5H
– 18 –
4. No adjust type (None adjusting circuit.)
5. Added EON button.
6. Need to change RDS logo due to add EON feature.
7. Added EON—TI, EON—PTY function.
5. Added EON button.
6. Need to change RDS logo due to add EON feature.
7. Added EON—TI, EON—PTY function.
3. Summary of CD-C5H RDS—EON operation
EON—PTY: Select and set the desired “PTY”
EON—PTY: Select and set the desired “PTY”
→
stand-by
→
switch to ON(other network) Station at the start of desired
PTY automatically
→
stay and listen to PTY of ON station
→
switch back to TN(This net) station automatically
at the end of PTY(ON) i.e. after changing to another PTY(except AFFAIRS) or cancelling to receive PTY of
ON station midway.
ON station midway.
EON—TI:
Select and set the “TI”
→
stand-by
→
switch to ON station at the start of traffic announcement automati
cally
→
stay and listen to TA of ON station
→
switch back to TN station autmatically at the end of TA(ON).
ie after TA(ON) is over or cancelled to receive TA of ON station midway.
When switching TN
→
ON station.
In case of exist 2 more stations having the desired(specified) “PTY” or “TI”, the receiver will select and switch to ON station
comparing field strength at the same time. But when the frequency of ON station exists in the preset-memory, then reciver
switches straight to that ON station(CH), without comparing field strength so can make a quick switching from TN—ON sta
tion. Preset memory takes priority of switching TN—ON station.
comparing field strength at the same time. But when the frequency of ON station exists in the preset-memory, then reciver
switches straight to that ON station(CH), without comparing field strength so can make a quick switching from TN—ON sta
tion. Preset memory takes priority of switching TN—ON station.
therefore ASPM is usefull not only for PTY search but also for rapid EON switching. Anyway CD-C5H EON is basically stand-
by and receiving method, along with the Guidelines for EON implementation.
by and receiving method, along with the Guidelines for EON implementation.
• ASPM SCAN: 87.50MHz
→
108.00 MHz.
• Only RDS signal is memorized by ASPM because RDS signal has PI code and is suitable and convenient for ASPM operation.
ASPM
Comparing field strength, only one strongest RDS station is memorized of all stations (repeater relay stations) that have same
ASPM
Comparing field strength, only one strongest RDS station is memorized of all stations (repeater relay stations) that have same
PI code.
Same PI code — freq: different
(AF’S)
PS: same
PTY: same
PTY: same
Each PI has AF’S list by individually.
Exa: P1 has f
Exa: P1 has f
1
, f
2
, f
3
(same PTY).
P2 has f
4
, f
5
(same PTY).
[For example]
Pickup and memorized to preset CH.
f 1
f 2
f 2
f 3
P 1 (PI cord)
PS 1 (Station Name)
PS 1 (Station Name)
f 5
f 4
P 2
PS 2
PS 2
f 6
f 7
f 7
f 8
P 3
PS 3
PS 3
f 9
f 10
f 11 f 12 f13
P 4
PS 4
PS 4
Select signals (f1, f5, f7, f10) are memorized in the preset memory by ASPM.
• If tentative - ASPM operation is repeated intententionally, never memorized (over write) at the same frequecy.
• If tentative - ASPM operation is repeated intententionally, never memorized (over write) at the same frequecy.
1st time ASPM
→
strongest stations of each pi are memorized.
ASPM is not only very usefull for PTY search, but also EON operation.
2nd time ASPM
2nd time ASPM
→
2nd strong stations of each pi are memorized and so on.
PTY search function is equal to FM band search function as a result.
1. Introduction of RDS for CD-C5H
CD-C5H RDS function is equal to adding EON feature to the current CD-C75H RDS.
EON feature is EON—PTY and EON—TI.
Although PTY and TI indicators are separated, PTY contains TI in the PTY items (software) like current PTY search items.
EON feature is EON—PTY and EON—TI.
Although PTY and TI indicators are separated, PTY contains TI in the PTY items (software) like current PTY search items.
NEWS,
AFFAIRS,
INFO,
ALARM,
TI
(TTL 17 kinds)
EON—PTY
EON—TI
Can select and stand-by
Can select and stand-by
EON—PTY and EON—TI are basically stand-by
→
receive the desired program of ON station.
2.The difference point from current CD-C75H RDS. (CD-C75H — CD-C5H)
1. PTY item: added TA.TTL 18 kind.
2. Each “TP”, “TA” ind. light up or go out individually.
“TA” ind. doesn’t light up on current model, CD-C75H due to none EON—TI.
3. Added 3 indicators(in FL) due to adding EON feature.
EON: Lights up only during receiving EON data (14A).
TI:
2. Each “TP”, “TA” ind. light up or go out individually.
“TA” ind. doesn’t light up on current model, CD-C75H due to none EON—TI.
3. Added 3 indicators(in FL) due to adding EON feature.
EON: Lights up only during receiving EON data (14A).
TI:
During EON-TI stand-by
→
Light up
During receiving ON station.
→
blink.
PTY: During EON-PTY stanb-by
→
Light up
During receiving ON station.
→
blink.
---
---
↑
↑
CD-C5H,CP-C5H
– 19 –
EON summary notice for reference
1. EON-TI/PTY
EON stand-by can be set, only when EON ind. lights up.
While EON ind. goes out (NO EON STATION), EON stand-by can't be set.
If the EON button is pressed, then “NO EON” is indication the display.
While EON ind. goes out (NO EON STATION), EON stand-by can't be set.
If the EON button is pressed, then “NO EON” is indication the display.
2. EON-TI/PTY
Even if switch back ON
→
TN station continue to keep EON stand-by.
3. EON-TI
Don’t switch TN
→
ON during TN broadcast TA. (same item)
4. EON-TI/PTY
EON can be cancelled during receiving ON station by pressing EON button if necessary and
switch back ON
switch back ON
→
TN.
5. EON-TI/PTY
EON stand-by is perfectly cancelled (cleared) by pressing EON button 2 times during stand-by or
powerOFF or Tun Up/ Down or change band or recall pre-set CH.
6. EON-TI/PTY
6. EON-TI/PTY
After setting EON stand-by, stand-by items can be confirmed by pressing EON button one time.
7. EON-TI/PTY
EON button function: •EON setting
•Confirm stand-by items
•Cancel (ON
•Cancel (ON
→
TN)
•EON clear cancel (2 times)
8. EON-TI/PTY
After setting EON-TI and EON-PTY stand-by, if when EON data is not transmitted, EON ind goes out
and EON stand-by is automatically cancelled display “NO EON”.
and EON stand-by is automatically cancelled display “NO EON”.
9. EON-TI
EON-TI stand-by can't be set. When TP=0,TA=0(TN) even if EON ind. lights up and the EON button is
pressed then “NO TI” is indication the display.
pressed then “NO TI” is indication the display.
10. EON-PTY
Don’t switch TN
→
ON during TN broadcast same specified PTY. (same item of PTY)
11. EON-TI/PTY
Switch TN
→
ON
→
TN station one cycle.
Never switch TN
→
ON1
→
ON2
→
Other net to other net station.
12. EON-TI/PTY
After switch TN
→
ON station. When ON station is NO RDS, NO signal, TA=OFF or different PTY items.
The receiver switch back ON
→
TN displaying “NO READY”.
13.
During receive ON station. when ON station become to be NO RDS, NO signal, TA=ON to OFF or
different PTY item, The receiver switch back ON
different PTY item, The receiver switch back ON
→
TN.
14. EON-TI/PTY
Switch TN
→
ON in case of 2 more stations exist, comparing field strength and switch to the strongest
station, if these signals are same strength, switch to the first previous station.
If same frequency as AF'Sexists in the preset memory, then switch TN
If same frequency as AF'Sexists in the preset memory, then switch TN
→
ON (preset memory station)
straight.
In case of exist 2 more preset memories of AF’S,then switch to the preset CH which taken in EON DATA
first, also in this case no concern to field strength.
In case of exist 2 more preset memories of AF’S,then switch to the preset CH which taken in EON DATA
first, also in this case no concern to field strength.
15.
Even if switch TN
→
ON preset memory straight, that ON station is very weak signal, then search another
AF'S (ON) station comparing field strength and switch to the strongest station as a result. Of all atations
of AF'S are very weak or no good condition, then, switch back ON
of AF'S are very weak or no good condition, then, switch back ON
→
TN automatically display "NO
READY".
16. EON-TI/PTY
No linkage volume, power ON/OFF, and switch function.
Traffic Programme code
(TP)
Traffic Announcement code
(TA)
Applications
OFF
OFF
This programme does not carry traffic announcements nor does
it refer, via EON, to a programme that does.
it refer, via EON, to a programme that does.
OFF
ON
This programmecarries EON information about another
programme which gives traffic information.
programme which gives traffic information.
ON
OFF
This programme carries traffic announcements but none are
being broadcast at present and may also carry EON information
about other traffic announcements.
being broadcast at present and may also carry EON information
about other traffic announcements.
ON
ON
A traffic announcement is being broadcast on this programme at
present.
present.
CD-C5H,CP-C5H
– 20 –
NOTES ON SCHEMATIC DIAGRAM
• Resistor:
To differentiate the units of resistors, such symbol as K and
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to electro-
lytic capacitor, the expression “capacitance/withstand volt-
age” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to electro-
lytic capacitor, the expression “capacitance/withstand volt-
age” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for this
model are subject to change for improvement without prior
notice.
notice.
• The indicated voltage in each section is the one measured by
Digital Multimeter between such a section and the chassis
with no signal given.
1. In the tuner section,
with no signal given.
1. In the tuner section,
( ) indicates AM
< > indicates FM stereo
< > indicates FM stereo
2. In the main section, a tape is being played back.
3. In the deck section, a tape is being played back.
3. In the deck section, a tape is being played back.
( ) indicates the record state.
4. In the power section, a tape is being played back.
5. In the CD section, the CD is stopped.
5. In the CD section, the CD is stopped.
• Parts marked with “ ” ( ) are important for
maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and
performance of the set.
parts with specified ones for maintaining the safety and
performance of the set.
SW701
VOLUME UP/DOWN
OFF
SW702
JOG DIAL
OFF
SW702A
PICKUP IN
OFF
SW703
X-BASS
OFF
SW704
EQUALIZER/DEMO
OFF
SW705
SRS MODE
OFF
SW706
SRS PASS
OFF
SW707
FF
OFF
SW708
STOP
OFF
SW709
EDIT NORMAL
OFF
SW710
EDIT HIGH
OFF
SW711
RECORD/PAUSE
OFF
SW712
FORWARD PLAY
OFF
SW713
DOLBY-NR
OFF
SW714
Q-SOUND
OFF
SW715
VIRTUAL
OFF
SW716
DOLBY-PRO LOGIC
OFF
SW717
REWIND
OFF
SW718
CD PAUSE
OFF
SW719
REVERSE PLAY
OFF
SW720
REVERSE MODE
OFF
SW721
CLOCK
OFF
SW722
TIMER
OFF
SW723
SLEEP
OFF
SW724
VIDEO/AUX
OFF
SW725
TAPE 1/2
OFF
SW726
TUNER (BAND)
OFF
SW727
CD
OFF
SW728
RDS PROGRAMME TYPE/
OFF
TRAFFIC INFORMATION SEARCH
SW729
RDS EON
OFF
SW730
RDS DISPLAY
OFF
SW731
RDS ASPM
OFF
SW732
CLEAR
OFF
SW733
MEMORY/SET
OFF
SW734
ON/STAND-BY
OFF
SW739
DISC 3 OPEN/CLOSE
OFF
SW740
DISC 3
OFF
SW741
DISC 2 OPEN/CLOSE
OFF
SW742
DISC 2
OFF
SW743
DISC 1 OPEN/CLOSE
OFF
SW744
DISC 1
OFF
SWB101,102 CAM1, 2
OFF
SWB103,104 CAM3, 4
OFF
SWB105
CD EJECT
OFF
SWB106
CD TRAY CLOSE
OFF
SWB107
CD IN
OFF
SWB108
CD SET
OFF
SWE1
TAPE 1 PLAY
OFF
SWE2
TAPE 1 CrO
2
OFF
SWE4
TAPE 2 PLAY
OFF
SWE5
TAPE 2 CrO
2
OFF
SWE7
TAPE 2 SIDE A FP
OFF
SWE8
TAPE 2 SIDE B FP
OFF
POSITION
REF. NO
DESCRIPTION
REF. NO
DESCRIPTION
POSITION
Click on the first or last page to see other CD-C5H service manuals if exist.