DOWNLOAD Sharp CD-C470E (serv.man3) Service Manual ↓ Size: 2.94 MB | Pages: 76 in PDF or view online for FREE

– 13 –

SP out

L-ch

Input signal is output.

(SO901)

R-ch

Input signal is output.

(SO903) SP out C-ch

SP cut, no output

(SO902) SP out S-ch

Almost no output (only omitting component)

SP out

L-ch

Almost no output (only omitting component)

(SO901)

R-ch

Almost no output (only omitting component)

(SO903) SP out C-ch Input signal is output.

(SO902) SP out S-ch

Almost no output (only omitting component)

IC202

16 pin L-out

Output enabled state

Output enabled state

Output enabled state

15 pin R-out

Output enabled state

Output enabled state

Output enabled state

IC201

 34pin C-out

No output

Output enabled state

No output

IC202

13pin  S-out

No output

Output enabled state

Output enabled state

SP OUT

L-ch

Output enabled state

Output enabled state

Output enabled state

(SO901)

R-ch

Output enabled state

Output enabled state

Output enabled state

 SP OUT C-ch

No output in MUTE (Q504) state

Output enabled state

No output in MUTE (Q504) state

(SO903)

SP OUT S-ch

No output in MUTE (Q503) state

Output enabled state

Output enabled state

(SO902)

Test tone output
• Pro Logic ON Normal mode
   Press the remote control TEST TONE button.
      

 →

Output of only L-ch

 →

Output of only C-ch

   

 ↑

                                                                    ↓

          Output of only S-ch 

←

 Output of only R-ch

   The test tone (noise) is repeatedly output for output period
   (2 sec).
   In this case the following indication appears repeatedly.
      

 →

TEST

 →

L-ch

 →

C-ch

                

  ↑

                ↓

            

S-ch

 ←

 R-ch

• Pro Logic ON Phantom mode
   Press the remote control TEST TONE button.
      

 →

Output of only L-ch

 →

Output of only R-ch

                

                    ↑

                                    ↓

                                        

←

 Output of only S-ch

   The test tone (noise) is repeatedly output for output period
   (2 sec).

   In this case the following indication appears repeatedly.
    

→

TEST 

→ 

L-ch 

→ 

R-ch

                      

↑

 

           

↓

                       

←

 S-ch

←

• Namely, two speakers are connected in parallel to one

amplifier.

• In the Pro Logic BYPASS mode the amplifier for C-ch (center

channel) and the amplifier for S-ch (surround channel) are in
MUTE state. The SP output is cut.

• In the normal mode of Pro Logic ON mode the amplifiers for

C-ch and S-ch are in operative state, so that the SP output
appears.

• In the Phantom mode of Pro Logic ON mode the amplifier for

C-ch is in MUTE state, so that the SP output is cut. The
amplifier for S-ch (surround) is in operative state, so that the
SP output appears

 

Relation between VIDEO IN input and output in Pro Logic
ON state
(1) L-ch/R-ch same phase input into VIDEO IN input jack in

VIDEO Function mode

(2) L-ch/R-ch reverse phase input into VIDEO IN input jack in

VIDEO Function mode

(Reverse phase: Phase difference between L and R is 180

°

)

SP out

L-ch

Almost no output (only omitting component)

(SO901)

R-ch

Almost no output (only omitting component)

(SO903) SP out C-ch

Almost no output (only omitting component)

(SO902) SP out S-ch

Input signal is output.

SP out

L-ch

Almost no output (only omitting component)

(SO901)

R-ch

Almost no output (only omitting component)

(SO903) SP out C-ch

SP cut, no output

(SO902) SP out S-ch

Input signal is output.

• Accordingly, if you want to output signal waveform to C-ch SP

out, give the same phase input into L-ch/R-ch INPUT in the
Pro Logic Normal mode.

   If one of channels receives input, C-ch does not output.  Only

L-ch or R-ch outputs.

• If you want to output signal waveform to S-ch SP out, you can

use either Normal mode or Phantom mode.  However, 180

°

reverse phase input must be given to L-ch/R-ch INPUT.

– 14 –

1.  RDS Function

PI

ASPM

PS

STATION NAME

PTY

PTY SEARCH

PTY(31)
EON TI (TA)

STAND-BY MODE

EON-PTY

EON-TI/PTY

EON-AF

With EON-AF

TP

ind.

TA

ind.

2.  DISPLAY and control buttons

Select and search (18 kind items) by cyclic
NEWS-AFFAIRS  ------  OTHER M - ALARM - TP - TA

Select and stand-by (17 kind items) by cyclic
NEWS-AFFAIRS  ------  OTHER M - ALARM - TI

RDS
EON

TA TP
PTY TI

DISPLAY

8 character can display E1 table of EBU.
Same as CD-C75H.

Lights up when RDS with EON station is received.

Lights up when RDS station is received.

Lights up when TA station is received.

Lights up when TP station is received.

Lights up when stand-by mode and blinks during staying other network
station.

ASPM

DISPLAY PTY•TI

SEARCH
SET

PTY•TI
SELECT

EON

PTY and TI  items can be
selected when use PTY search
or EON STAND-BY

Can use for
• EON setting
• confirm stand-by item
• cancel (ON

→

TN)

• EON clear cancel

18 kind
(contain TP, TA)

17 kind
(contain TI)

Note:
TP and TA ind. are different from CD-C75H.
TP, TA ind. can light up individually, when TP: OFF and TA: ON, it means that EON-TI can be used, in case of TP=OFF,
TA=OFF, EON-Ti can't be used.
In case of CD-C75H, (TP: OFF and TA: ON) disregard (ignore) this case, because EON-TI is nothing.

AF: Alternative Frequencycies

– 15 –

No

Hold down the 

ASPM button for 3 more second.

“ASPM” blinks in the display

.

Preset CH memory full over?

No operate. 

After displayed “END”. Return to

previous station.

SD (TUNE) DET out OK?

If count 1st OK?

If count 2nd OK?

RDS signal or not?   PI—identify

Comparing PI cord same or not?

between current receiving PI and

before PI which is already memorized

by 

ASPM on this time.

Comparing freg. same or not?

between current receiving frequency

and (already) previously memorized

frequency

.

Memorized to the lowest

vacant preset channel.

Preset CH memory become full over?

Begin to 

ASPM SCAN from the next

CH-SP

AN again.

Repeat and continue with same format

ASPM operation untill 108 MHz.

After reached 108 MHz, displayed the

TTL quantity of memorized stations.

And return to the previous receiving

freq. automatically

.

Displayed the 

TTL

 quantity of memo-

rized stations by 

ASPM operation on

this time. 

And return to the previous

receiving freq. automatically

.

Ye

s

No

Ye

s

Ye

s

Ye

s

Ye

s

No

No

No

No

No

No

Ef

fect

Pass

No ef

fect

Pass

No ef

fect

Pass

No ef

fect

Pass

No ef

fect

Ye

s

No

Ye

s

Compare the field strength of current

receiving signal. Is receiving signal

stronger than signal which has same PI

cord and is already memorized to

preset memory ahead of this receiving

time?

Ye

s

No ef

fect

No

No ef

fect

Comparing freg. same or not?

Between current receiving frequency

and (already) previously memorized

frequency

.

Ye

s

Memorized to the lowest

vacant preset channel.

Ye

s

No ef

fect

Begin to scan start 87.50 

→ 

108.00 MHz

– 16 –

4. No adjust type (None adjusting circuit.)
5. Added EON button.
6. Need to change RDS logo due to add EON feature.
7. Added EON—TI, EON—PTY function.

EON—PTY:

Select and set the desired “PTY” 

→ 

stand-by

→ 

switch to ON(other network) Station at the

start of desired PTY automatically 

→ 

stay and listen to PTY of ON station 

→ 

switch back to TN(This net) station

automatically at the end of PTY(ON) i.e. after changing to another PTY(except AFFAIRS) or cancelling to receive PTY of ON
station midway.
EON—TI:

Select and set the “TI” 

→ 

stand-by 

→ 

switch to ON station at the start of traffic announcement automati

cally 

→ 

stay and listen to TA of ON station 

→ 

switch back to TN station autmatically at the end of TA(ON).

ie after TA(ON) is over or cancelled to receive TA of ON station midway.

When switching TN 

→ 

ON station.

In case of exist 2 more stations having the desired(specified) “PTY” or “TI”, the receiver will select and switch to ON station
comparing field strength at the same time. But when the frequency of ON station exists in the preset-memory, then reciver
switches straight to that ON station(CH), without comparing field strength so can make a quick switching from TN—ON sta
tion. Preset memory takes priority of switching TN—ON station.
therefore ASPM is usefull not only for PTY search but also for rapid EON switching. Anyway CD-C470H/CD-C480H’s EON is
basically stand-by and receiving method, along with the Guidelines for EON implementation.

• ASPM SCAN: 87.50MHz 

→

 108.00 MHz.

• Only RDS signal is memorized by ASPM because RDS signal has PI code and is suitable and convenient for ASPM operation.
  ASPM
  Comparing field strength, only one strongest RDS station is memorized of all stations (repeater relay stations)  that have same

PI code.

Same PI code —  freq: different

   (AF’S)

      PS: same
      PTY: same

Each PI has AF’S list by individually.
Exa: P1 has f

1

, f

2

, f

3

 (same PTY).

        P2 has f

4

, f

5

 (same PTY).

Pickup and memorized to preset CH.

f 1
f 2

f 3

P 1 (PI cord)
PS 1 (Station Name)

f 5

f 4

P 2
PS 2

     f 6
f 7

f 8

P 3
PS 3

f 9

f 10

f 11  f 12  f13

P 4
PS 4

  Select signals (f1, f5, f7, f10) are memorized in the preset memory by ASPM.
• If tentative - ASPM operation is repeated intententionally, never memorized (over write) at the same frequecy.

1st time ASPM 

→ 

strongest stations of each pi are memorized.

ASPM is not only very usefull for PTY search, but also EON operation.
2nd time ASPM 

→

 2nd strong stations of each pi are memorized and so on.

PTY search function is equal to FM band search function as a result.

CD-C470H/CD-C480H RDS function is equal to adding EON feature to the current CD-C75H RDS.
EON feature is EON—PTY and EON—TI.
Although PTY and TI indicators are separated, PTY contains TI in the PTY items (software) like current PTY search items.

NEWS,

AFFAIRS,

INFO,

ALARM,

TI

(TTL 17 kinds)

EON—PTY

EON—TI

Can select and stand-by

Can select and stand-by

EON—PTY and EON—TI are basically stand-by 

→

 receive the desired program of ON station.

1. PTY item: added TA.TTL 18 kind.
2. Each “TP”, “TA” ind. light up or go out individually.
    “TA” ind. doesn’t light up on current model, CD-C75H due to none EON—TI.
3. Added 3 indicators(in FL) due to adding EON feature.
    EON: Lights up only during receiving EON data (14A).
    TI:

During EON-TI stand-by 

→

 Light up

During receiving ON station. 

→

 blink.

    PTY: During EON-PTY stanb-by 

→

 Light up

During receiving ON station. 

→

 blink.

---

---

↑

↑