Sharp AE-XM18CR (serv.man16) Service Manual ▷ View online
59
AY-XM7/9/12CR
AY-XPM7/9/12CR
AE-XM18/24CR
AY-XPM7/9/12CR
AE-XM18/24CR
DISASSEMBLING PROCEDURE
FOR INDOOR UNIT [AY-XPM7CR/9CR/12CR]
CAUTION : DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY SERVICING
1. Open the opne panel, and remove 2 air filters.
2. Remove 4 screws fixing the front panel.
3. Remove the screw fixing the cord clamp.
Note :
During reassembly, install the holder after installing the
front panel. This will make it
easier to assemble the front panel.
Note :
During reassembly, install the holder after installing the
front panel. This will make it
easier to assemble the front panel.
4. Close the open panel. Pushing the nail of the front
panel.
5. Pull the front panel up.
6. Remove the unit-to-unit wiring from the terminal
board.
7. Remove a screw fixing the control box cover, and
remove it.
8. Remove 2 screws fixing the 2 ground wires and
terminal.
Note :
During reassembly, take care direction of the lead wires.
During reassembly, take care direction of the lead wires.
60
AY-XM7/9/12CR
AY-XPM7/9/12CR
AE-XM18/24CR
AY-XPM7/9/12CR
AE-XM18/24CR
CN1
CN5
CN4
CN3
9. Remove 2 screws fixing the sensor holder, lead cover
A and lead cover B from the evaporator.
NOTE : In case of AY-XPM7CR, AY-XPM9CR
10-1.Cut off 2 fixing bands.
During reassembly, fix them by fixing bands as same
certainly.
certainly.
NOTE : In case of AY-XPM12CR
10-2.Cut off 3 fixing bands.
During reassembly, fix them by fixing bands as same
certainly.
certainly.
11. Remove 2 thermistors of the evaporator and the pipe.
12.Remove 4 conectors.
13. Pushing the 2 hooks of the holder, remove the display
board unit 3 from the holder.
And remove 2 screws fixing the cluster holder from the
drain pan.
And remove 2 screws fixing the cluster holder from the
drain pan.
14.Remove 3 screws fixing the LED HOLDER B
15. Remove the screw fixing the pipe holder.
61
AY-XM7/9/12CR
AY-XPM7/9/12CR
AE-XM18/24CR
AY-XPM7/9/12CR
AE-XM18/24CR
16. Remove 3 screws fixing the control box,and remove
the control box.
17. Remove a screw fixing the drain pan.
18. Pull the drain pan toward you.
19. Remove the drain cover from the evaporator.
Note:
During reassembly, verify that the dew on
the pipe is led to the drain pan.
20. Remove 4 screws fixing the evaporator.
21. Remove the evaporator from the cabinet.
22. Remove 3 screws fixing the motor cover, and pull up
the fan.
23.Loose a screw fixing fan.
62
AY-XM7/9/12CR
AY-XPM7/9/12CR
AE-XM18/24CR
AY-XPM7/9/12CR
AE-XM18/24CR
DISASSEMBLING PROCEDURE
FOR INDOOR UNIT [AY-XM7CR/9CR/12CR]
CAUTION : DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY SERVICING
1. Open the opne panel, and remove 2 air filters.
2. Remove 4 screws fixing the front panel.
3. Remove the screw fixing the cord clamp.
Note :
During reassembly, install the holder after installing the
front panel. This will make it
easier to assemble the front panel.
Note :
During reassembly, install the holder after installing the
front panel. This will make it
easier to assemble the front panel.
4. Close the open panel. Pushing the nail of the front
panel.
5. Pull the front panel up.
6. Remove the unit-to-unit wiring from the terminal
board.
7. Remove a screw fixing the control box cover, and
remove it.
8. Remove 2 screws fixing the 2 ground wiredfs and
terminal.
Note :
During reassembly, take care direction of the lead wires.
During reassembly, take care direction of the lead wires.
