DOWNLOAD Panasonic Z8 / Chassis Service Manual ↓ Size: 1.18 MB | Pages: 47 in PDF or view online for FREE

Model
Z8 Chassis
Pages
47
Size
1.18 MB
Type
PDF
Document
Service Manual / Other
Brand
Device
TV / Z8
File
z8-chassis.pdf
Date

Panasonic Z8 / Chassis Service Manual / Other ▷ View online

3DQDV
RQ
LF
2
.3
.
V
ide
o
a
nd
Mono
Audi
o
Bl
oc
k
D
ia
gra
m
3DQDV
RQ
LF
2.4.
V
id
e
o
a
n
d
S
ter
eo
A
u
d
io
Bl
oc
k
D
ia
gra
m

3DQDVRQLF
3.
Power Supply
The mains AC voltage used for Z8 is fed via connector
E2 situated on the E-Board. From the connector E2
the mains AC power supply is fed via the main TV
On/Off switch S801 and line suppression filter L801
before being fed to the standby transformer T801.
At the standby transformer T801 the AC supply splits
into two paths.
The first path sees the AC supply being fed to the
normally open contact of the standby relay RL801.
The second path has the AC supply being fed via the
windings P2/P1 of the standby transformer T801.
3.1.
Standby Power Supply Circuit
The standby transformer T801 has the AC supply as
just mentioned being fed via the primary winding
P2/P1.
The output of the secondary windings S2/S1 of the
standby transformer is fed to the bridge rectifier
D1201, where the AC voltage is full rectified. Here the
supply takes two paths.
The first path provides smoothing to the supply via
capacitor C1201 before being fed to IC1202 pin 1.
The output at pin 3 is smoothed further by capacitor
C1203, and the 5V standby supply output is fed to the
EEPROM IC1103, the remote control receiver
IC1104 and the Q-Link circuit. The 5V standby supply
is also fed to IC1201, where the output at pin 3 is
smoothed via C1204, to provide 3.3V standby supply
to the Ultimate One Chip (UOC) IC IC601 pin 61, and
the reset IC IC1102. This 3.3V is also used to bias the
standby relay control transistor Q1204.
The second path from the bridge rectifier sees the
supply voltage being fed via resistor R1202 to the
standby relay RL801 and the relay winding to the
collector of transistor Q1201. Transistor Q1201,
which is controlled by Q1204, is responsible for
switching the TV in and out of standby, under the
control of the UOC IC IC601 pin 1.
The two supplies mentioned allow the circuits to
operate during standby, which is required to process
the switch ON command from the remote control or
local keys, allowing the TV to be switched out of
standby.
To reduce the load on the standby transformer T801,
a 10V supply is fed from transformer T552 pin 6 via
rectifying diode D554, R1209 and D1205, to pin 1 of
IC1202.
3DQDVRQLF
3.2.
Power Supply Circuit
The STR-F6523, IC801 is used in the Z8 power
supply to control and regulate the power supply
operation.
This
device
features
over-voltage
protection and thermal shutdown. The output stage of
the IC incorporates a built-in MOSFET switching
transistor.
3.3.
Operation
The supply voltage for the main power supply circuit
is fed via the standby relay RL801 to the bridge
rectifier D802 where the AC voltage is fully rectified
and smoothed by capacitor C809.
This smoothed DC voltage of approximately 300V
then feeds the supply to pin 3 of the switched mode
power supply IC IC801, where the DC voltage is held
at the drain of the internal MOSFET, by its parallel
zener diode.
Page of 47
Display

Click on the first or last page to see other Z8 / Chassis service manuals if exist.