Panasonic TX-LR32E6 Service Manual ▷ View online
TX-LR32E6
5
2.2.
About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
Caution
• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70
F (30~40 C) higher. Please
use a high temperature soldering iron and set it to 700 ± 20
F (370 ± 10 C).
• Pb free solder will tend to splash when heated too high (about 1100
F or 600 C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the
opposite side. (see figure below)
TX-LR32E6
6
3 Service Navigation
3.1.
Service Hint
Board Name
Main Device
Remarks
A BOARD
TUN, OFDM, ADV, LD4, STBY EEP
Repairable
P BOARD
Power Supply
Repairable
K BOARD
LED/RM/CATS
Repairable
TX-LR32E6
7
4 Specifications
Note
• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
• For the information of the open source software, refer to [eHELP] (Support > Licence).
• For the information of the open source software, refer to [eHELP] (Support > Licence).
Rated power consumption
80 W
Standby power consumption
*1
0.20 W
Visible screen size (diagonal)
80 cm / 32 inches
Dimensions (W
H D)
724 mm
489 mm 207 mm (With Pedestal)
724 mm
434 mm 53 mm (TV only)
Mass
9.5 kg Net (With Pedestal)
8.5 kg Net (TV only)
8.5 kg Net (TV only)
Power source
AC 220-240 V, 50 / 60 Hz
Display Resolution
1,920 (W)
1,080 (H)
Panel
LED LCD panel
Connection Terminals
AV1 input / output
SCART (Audio/Video in, Audio/Video out, RGB in)
AV2 input
VIDEO
RCA PIN Type
1
1.0 V[p-p] (75
)
(COMPONENT / VIDEO)
AUDIO L - R
RCA PIN Type
2
0.5 V[rms]
Y
1.0 V[p-p] (including synchronisation)
P
B
, P
R
±0.35 V[p-p]
HDMI 1 / 2 / 3 input
TYPE A Connectors
HDMI 1 / 3: Content Type, Deep Colour
HDMI 2: Content Type, Audio Return Channel, Deep Colour
HDMI 1 / 3: Content Type, Deep Colour
HDMI 2: Content Type, Audio Return Channel, Deep Colour
• This TV supports “HDAVI Control 5” function.
Card slot
Common Interface slot (complies with CI Plus)
1
ETHERNET
RJ45, IEEE802.3 10BASE-T / 100BASE-TX
USB 1 / 2
USB2.0 DC 5 V, Max. 500 mA
DIGITAL AUDIO Output
PCM / Dolby Digital / DTS, Fibre optic
Receiving systems / Band name
DVB-C
Digital cable services (MPEG2 and MPEG4-AVC(H.264))
Check the latest information
DVB-T / T2
Digital terrestrial services (MPEG2 and MPEG4-AVC(H.264))
on the available services at
PAL D, K,
VHF R1 - R2
VHF R3 - R5
the following website.
SECAM D, K
VHF R6 - R12
UHF E21 - E69
(English only)
PAL 525/60
Playback of NTSC tape from some PAL Video recorders (VCR)
http://panasonic.net/viera/support
M.NTSC
Playback from M.NTSC Video recorders (VCR)
NTSC (AV input only)
Playback from NTSC Video recorders (VCR)
Aerial input
VHF / UHF
Sound
Speaker
(90 mm
22 mm) 2 8
Audio output
20 W (10 W + 10 W)
Headphones
M3 (3.5 mm) stereo mini Jack
1
Operating Conditions
Temperature : 0
C - 35C
Humidity : 20% - 80% RH (non-condensing)
Built-in wireless LAN
Standard compliance and Frequency range*
2
:
IEEE802.11a/n
5.180 GHz - 5.320 GHz, 5.500 GHz - 5.580 GHz, 5.660 GHz - 5.700 GHz
IEEE802.11b/g/n
2.412 GHz - 2.472 GHz
Security: WPA2-PSK (TKIP/AES)
5.180 GHz - 5.320 GHz, 5.500 GHz - 5.580 GHz, 5.660 GHz - 5.700 GHz
IEEE802.11b/g/n
2.412 GHz - 2.472 GHz
Security: WPA2-PSK (TKIP/AES)
WPA-PSK (TKIP/AES)
WEP (64 bit/128 bit)
*1: when the TV is turned off with the remote control and no function is active
*2: The frequency and channel differ depending on the country. Follow the regulations of your country for the frequency range.
*2: The frequency and channel differ depending on the country. Follow the regulations of your country for the frequency range.
TX-LR32E6
8
5 Service Mode
5.1.
How to enter into Service Mode
5.1.1.
Purpose
After exchange parts, check and adjust the contents of adjustment mode.
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
5.1.2.
Key command
[1] button...Main items Selection in forward direction
[2] button...Main items Selection in reverse direction
[3] button...Sub items Selection in forward direction
[4] button...Sub items Selection in reverse direction
[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
[2] button...Main items Selection in reverse direction
[3] button...Sub items Selection in forward direction
[4] button...Sub items Selection in reverse direction
[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
5.1.3.
How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
5.1.4.
Contents of adjustment mode
• Value is shown as a hexadecimal number.
• Preset value differs depending on models.
• After entering the adjustment mode, take note of the value in each item before starting adjustment.
• Preset value differs depending on models.
• After entering the adjustment mode, take note of the value in each item before starting adjustment.
Main item
Sub item
Sample Data
Remark
ADJUST
CONTRAST
default value
COLOR
default value
TINT
default value
SUB-BRT
default value
BACKLGT
default value
B-Y-G
default value
R-Y-A
default value
V COM
default value
WB-ADJ
R-GAIN
default value
G-GAIN
default value
B-GAIN
default value
R-CENT
default value
G-CENT
default value
B-CENT
default value
OPTION
Boot
default value
Factory Preset.
STBY-SET
default value
EMERGENCY
default value
CLK MODE
default value
CLOCK
default value
EDID-CLK
default value
SRV-TOOL
default value
See next.
Click on the first or last page to see other TX-LR32E6 service manuals if exist.