DOWNLOAD Panasonic TX-LR32E6 Service Manual ↓ Size: 4.65 MB | Pages: 68 in PDF or view online for FREE

Model
TX-LR32E6
Pages
68
Size
4.65 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / CHASSIS LA41
File
tx-lr32e6.pdf
Date

Panasonic TX-LR32E6 Service Manual ▷ View online

TX-LR32E6
4
2 Warning
2.1.
Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity.  Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor  [chip] components.  The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground.  Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device.  Some solder removal devices not classified as [anti-static (ESD protected)] can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals.   These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or
comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).
TX-LR32E6
5
2.2.
About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 
F (30~40 C) higher. Please
use a high temperature soldering iron and set it to 700 ± 20 
F (370 ± 10 C).
• Pb free solder will tend to splash when heated too high (about 1100 
F or 600 C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the
opposite side. (see figure below)
TX-LR32E6
6
3 Service Navigation
3.1.
Service Hint
Board Name
Main Device
Remarks
A BOARD
TUN, OFDM, ADV, LD4, STBY EEP
Repairable
P BOARD
Power Supply
Repairable
K BOARD
LED/RM/CATS
Repairable
TX-LR32E6
7
4 Specifications
Note
• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
• For the information of the open source software, refer to [eHELP] (Support > Licence).
Rated power consumption
80 W
Standby power consumption
*1
0.20 W
Visible screen size (diagonal)
80 cm / 32 inches
Dimensions (W 
 H  D)
724 mm 
 489 mm  207 mm (With Pedestal)
724 mm 
 434 mm  53 mm (TV only)
Mass 
9.5 kg Net (With Pedestal)
8.5 kg Net (TV only)
Power source
AC 220-240 V, 50 / 60 Hz
Display Resolution
1,920 (W) 
 1,080 (H) 
Panel
LED LCD panel
Connection Terminals
AV1 input / output
SCART (Audio/Video in, Audio/Video out, RGB in)
AV2 input 
VIDEO
RCA PIN Type 
 1
1.0 V[p-p] (75 
)
(COMPONENT / VIDEO)
AUDIO L - R
RCA PIN Type 
 2
0.5 V[rms]
Y
1.0 V[p-p] (including synchronisation)
P
B
, P
R
±0.35 V[p-p]
HDMI 1 / 2 / 3 input
TYPE A Connectors
HDMI 1 / 3: Content Type, Deep Colour
HDMI 2: Content Type, Audio Return Channel, Deep Colour
• This TV supports “HDAVI Control 5” function.
Card slot
Common Interface slot (complies with CI Plus) 
 1
ETHERNET
RJ45, IEEE802.3 10BASE-T / 100BASE-TX
USB 1 / 2
USB2.0 DC 5 V, Max. 500 mA
DIGITAL AUDIO Output
PCM / Dolby Digital / DTS, Fibre optic
Receiving systems / Band name
DVB-C
Digital cable services (MPEG2 and MPEG4-AVC(H.264))
Check the latest information
DVB-T / T2
Digital terrestrial services (MPEG2 and MPEG4-AVC(H.264))
on the available services at 
PAL D, K, 
VHF R1 - R2
VHF R3 - R5
the following website.
SECAM D, K
VHF R6 - R12
UHF E21 - E69
(English only)
PAL 525/60
Playback of NTSC tape from some PAL Video recorders (VCR)
http://panasonic.net/viera/support
M.NTSC
Playback from M.NTSC Video recorders (VCR)
NTSC (AV input only)
Playback from NTSC Video recorders (VCR)
Aerial input
VHF / UHF
Sound
Speaker
(90 mm 
 22 mm)  2    8
Audio output
20 W (10 W + 10 W)
Headphones
M3 (3.5 mm) stereo mini Jack 
 1
Operating Conditions
Temperature : 0
C - 35C  
Humidity : 20% - 80% RH (non-condensing)
Built-in wireless LAN
Standard compliance and Frequency range*
2
:
IEEE802.11a/n
5.180 GHz - 5.320 GHz, 5.500 GHz - 5.580 GHz, 5.660 GHz - 5.700 GHz
IEEE802.11b/g/n
2.412 GHz - 2.472 GHz
Security: WPA2-PSK (TKIP/AES)
WPA-PSK (TKIP/AES)
WEP (64 bit/128 bit)
*1: when the TV is turned off with the remote control and no function is active
*2: The frequency and channel differ depending on the country. Follow the regulations of your country for the frequency range.
Page of 68
Display

Panasonic TX-LR32E6 Service Manual ▷ Download

  • DOWNLOAD Panasonic TX-LR32E6 Service Manual ↓ Size: 4.65 MB | Pages: 68 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Panasonic TX-LR32E6 in PDF for free, which will help you to disassemble, recover, fix and repair Panasonic TX-LR32E6 TV. Information contained in Panasonic TX-LR32E6 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.