DOWNLOAD Panasonic TX-LR32D25 Service Manual ↓ Size: 15.45 MB | Pages: 85 in PDF or view online for FREE

TX-LR32D25

10

1. Select [SRV-TOOL] in Service Mode.
2. Press [OK] button on the remote control.

SOS History (Number of LED blinking ) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory
shipment setting].

Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3sec.
Time : Cumulative power on time, indicated hour : minute by decimal
Count : Number of ON times by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.

1. Disconnect the AC cord from wall outlet.

TX-LR32D25

11

1. Press the ‘RECALL’ button on the remote control and press ‘-’ vol button on the LCD panel.
2. Press button number 1 on the remote control to select for Adjustment.
3. Self Check to Exit.

1. Press the ‘MENU’ button (on the remote control) and the ‘DOWN’ button on the LCD panel.
2. Press ON/OFF button on the panel to Exit.

1. Press the ‘VOLUME DOWN’ button on the TV panel and simultaneously press the AV button on the remote control 3 times to

enter Hotel Mode.

2. Set Hotel mode ‘on’, then press ‘EXIT’ to come out.

Item

Function

Hotel Mode

Select hotel mode ON/OFF

Initial INPUT

Select input signal modes.
Set the input, when each time power is switched 
on.
Selection :
OFF/Analogue TV/Digital TV/AV1/AV2/AV3/PC/
HDMI1/HDMI2/HDMI3

• Off: give priority to a last memory.
• Selectable input is depend on the model.

Initial POS

Select programme number.
Selection :
Off/0 to 100

• Off: give priority to a last memory.

Initial VOL level

Adjust the volume when each time power is
switched on.
Selection/Range :
Off/0 to 100

• Off: give priority to a last memory.

Maximum VOL
level

Adjust maximum volume.
Range :
0 to 100

Button lock

Select local key conditions.
Selection :
Off/SETUP/MENU/All

• Off: altogether valid.
• SETUP: only F-key is invalid.

(Tuning guide (menu) can not be selected.)

• MENU: only F-key is invalid.

(only Volume/Mute can be selected.)

• ALL: altogether invalid.

Remote lock

Select remote control key conditions.
Selection :
Off/SETUP/MENU

• Off: altogether valid.
• SETUP: only Setup menu is invalid.
• MENU: Picture/Sound/Setup menu are invalid.

TX-LR32D25

12

Use the self-check function to test the unit.

1. Checking the IIC bus lines
2. Power LED Blinking timing

Self-check indication only:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control
for more than 3 seconds.
Self-check indication and forced to factory shipment setting:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote
control for more than 3 seconds.

Disconnect the AC cord from wall outlet.

Confirm the following parts if NG was displayed.

TX-LR32D25

13

1. Subject

Information of LED Flashing timing chart.

2. Contents

When an abnormality occurs, the protection circuit will operate and reset the unit to stand by mode. During this time, the
defective block can be identified by the number of blinking times of the Power LED on the front panel of the unit as follow:

First check point
There are following 2 states of No Power indication by power LED.

1. No lit
2. Red is lit then turns red blinking a few seconds later. (See 6.2.)

Blinking times

Contents

1

Inverter_SOS

2

FAN_SOS

3

SOS

4

SUB 12V_SENSE_SOS

7

Sub_ 3.3V_SENSE_SOS

9

SOUND_SOS

12

BE)Sld)_SOS

13

Emergency SOS