Panasonic TX-LR32D25 Service Manual ▷ View online
TX-LR32D25
4
2 Warning
2.1.
Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can
4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or
comparable conductive material).
comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).
sufficient to damage an ES device).
TX-LR32D25
5
2.2.
About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
Caution
• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70
°F (30~40 °C) higher. Please
use a high temperature soldering iron and set it to 700 ± 20
°F (370 ± 10 °C).
• Pb free solder will tend to splash when heated too high (about 1100
°F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the
opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
TX-LR32D25
6
3 Service Navigation
3.1.
Service Hint
Board Name
Main Device
A BOARD
AVSW, TUN, OFDM, ADV, P-AVC, GENX, EEP, TEMP
V BOARD
REMOTE, LED, LUMINUNCE SENSOR
T CON BOARD
T-CON for LG 100Hz panel
K BOARD
KEY, Power SW
P BOARD
Power Supply for IPS-
α
TX-LR32D25
7
3.2.
Applicable signals
Input signal that can be displayed
* Mark: Applicable input signal for Component (Y, P
B
, P
R
), HDMI and PC
Note:
• Signals other than above may not be displayed properly.
• The above signals are reformatted for optimal viewing on your display.
• The above signals are reformatted for optimal viewing on your display.
horizontal frequency (kHz)
vertical frequency (Hz)
COMPONENT
HDMI
PC
525 (480) / 60i
15.73
59.94
*
*
525 (480) /60p
31.47
59.94
*
*
750 (720) /60p
45.00
59.94
*
*
1,125 (1,080) /60i
33.75
59.94
*
*
640
× 400 @70
31.47
70.08
*
640
× 480 @60
31.47
59.94
*
Macintosh13 inch (640
× 480)
35.00
66.67
*
640
× 480 @75
37.50
75.00
*
852
× 480 @60
31.47
59.94
*
800
× 600 @60
37.88
60.32
*
800
× 600 @75
46.88
75.00
*
800
× 600 @85
53.67
85.08
*
Macintosh16 inch (832
× 624)
49.73
74.55
*
1,024
× 768 @60
48.36
60.00
*
1,024
× 768 @70
56.48
70.07
*
1,024
× 768 @75
60.02
75.03
*
1,024
× 768 @85
68.68
85.00
*
Macintosh 21 inch (1,152
× 870)
68.68
75.06
*
1,280
× 768 @60
47.70
60.00
*
1,280
× 1,024 @60
63.98
60.02
*
1,366
× 768 @60
48.36
60.00
*