Panasonic TX-L50ET60B / TX-L50ET60Y / TX-LR50ET60 Service Manual ▷ View online
Specifications
Power
Source:
220-240V AC, 50 / 60Hz
Rated Power Consumption:
113W
Stand-by Power Consumption:
0.20W
Aerial Impedance:
75
unbalanced, Coaxial Type
Receiving System:
L50ET60B (UK)
DVB-T/T2 Digital terrestrial services (
MPEG2 and MPEG4-AVC(H.264)
)
PAL I UHF E21-E68
PAL 525/60 (AV only)
M.NTSC (AV only)
NTSC (AV only)
L50ET60B (Ireland)
DVB-T Digital terrestrial services (
MPEG2 and MPEG4-AVC(H.264)
)
PAL I VHF A-J
UHF E21-E69
CATV S1-S20
CATV S21-S41(Hyperband)
PAL 525/60 (AV only)
M.NTSC (AV only)
NTSC (AV only)
L50ET60Y
DVB-T/T2 Digital terrestrial services (
MPEG2 and MPEG4-AVC(H.264)
)
DVB-C
Digital cable services (
MPEG2 and MPEG4-AVC(H.264)
)
PAL I/H, B/G,
SECAM B/G, L/L’
VHF E2-E12 VHF H1-H2 ( ITALY )
VHF A-H ( ITALY ) UHF E21-E69
CATV (S01-S05) CATV S1-S10(M1-M10)
CATV S11-S20 (U1-U10) CATV S21-S41 (HYPERBAND)
PAL D/K,
SECAM
D/K
VHF R1-R2 VHF R3-R5
VHF R6-R12 UHF E21-E69
PAL 525/60 (AV only)
M.NTSC (AV only)
NTSC (AV only)
LR50ET60
DVB-T/T2 Digital terrestrial services (
MPEG2 and MPEG4-AVC(H.264)
)
DVB-C
Digital cable services (
MPEG2 and MPEG4-AVC(H.264)
)
PAL D/K,
SECAM
D/K
VHF R1-R2 VHF R3-R5
VHF R6-R12 UHF E21-E69
PAL 525/60 (AV only)
M.NTSC (AV only)
NTSC (AV only)
Aerial - Rear:
L50ET60B (UK) L50ET60B (Ireland) / L50ET60Y / LR50ET60
UHF VHF/UHF
Operating Conditions:
Temperature: 0°C
35°C
Humidity:
20%
80% RH (non condensing)
Terminals:
AV1 IN
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 10k
RGB (21 pin)
0.7V p-p 75
AV1 OUT
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 1k
AV2 IN
Video (RCAx1)
1V p-p 75
(COMPONENT/VIDEO)
Audio (RCAx2)
500mV rms 10k
(used for HDMI_ AV2 audio IN)
Video (RCAx3)
Y:1V p-p 75
(including synchronization)
Pb, Pr: ±0.35V p-p 75
9
HDMI1, HDMI2, HDMI3
Type A Connectors
HDMI
1/3 : 3D, Content Type, Deep Colour
HDMI 2 : 3D, Content Type, Audio Return Channel, Deep Colour
This TV supports “HDAVI Control 5” function.
DIGITAL AUDIO OUT
PCM / Dolby digital / DTS, Fiber optic
USB 1/2
USB 2.0 DC 5V Max 500mA
ETHERNET
RJ45, IEEE802.3 10BASE-T / 100BASE-TX
CARD SLOT
SD Card slot x1
Common interface slot (Complies with CI+) x1
Wireless LAN:
Standard Compliance
IEEE802.11a/n , IEEE802.11b/g/n
Frequency Range
IEEE802.11a/n: 5.180 GHz – 5.320 GHz
5.500 GHz – 5.580 GHz
5.660 GHz – 5.700 GHz
IEEE802.11b/g/n: 2.412 GHz – 2.472 GHz
Security
WPA2-PSK
(TKIP/AES)
WPA-PSK
(TKIP/AES)
WEP(64
bit/128
bit)
3D Eyewear:
Dimensions (W x H x D)
165mm x 38m x 166mm
Mass
18g
Lens Type
Circularly-polarised filter
Usage Temperature Range
0°C
40°C
Materials
Main body / Lens section: Resin
LCD screen:
L5EDDYY00465
1920 x 1080, 16:9
Visible Diagonal 1260mm
Speaker:
8 train speakers x 2, Woofer (Ø 75mm) x 1
Audio
Output:
18W (4W + 4W + 10W)
Headphones:
3.5mm,
8
Impedance
Accessories supplied :
Remote Control
2 x R6 (UM3) Batteries
SCART
Cable
Dimensions:
Width:
Height: Depth:
Including TV stand
1,123mm 714mm 280mm
TV set only
1,123mm 659mm 35mm
Mass:
Including TV stand
19.5kg
TV set only
16.0kg
Design and Specifications are subject to change without notice. Mass and dimensions shown are approximate.
This equipment complies with the EMC standards listed below:
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024
10
Technical Description
Specification of KEY for CI Plus, DTCP-IP, One-to-One, Netflix, Widewine and HDCP
General information:
General information:
1. NAND FLASH (IC8900) for spare parts has the seed of KEY for each.
2. The final KEY data will be generated by MT5590 IC (IC8000) when SELF CHECK was done and are stored in both
MT5590 IC (IC8000) and NAND FLASH (IC8900).
All KEYs are not generated for all models.
The necessary KEY are only generated and stored depend on the feature of models.
2. The final KEY data will be generated by MT5590 IC (IC8000) when SELF CHECK was done and are stored in both
MT5590 IC (IC8000) and NAND FLASH (IC8900).
All KEYs are not generated for all models.
The necessary KEY are only generated and stored depend on the feature of models.
Replacement of ICs:
When MT5590 IC (IC8000) is replaced, NAND FLASH (IC8900) should be also replaced with new one the same time.
When NAND FLASH (IC8900) is replaced, MT5590 IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the MENU button on the remote
control for more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.
When NAND FLASH (IC8900) is replaced, MT5590 IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the MENU button on the remote
control for more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.
Model and Keys:
Keys
Model No.
CI PLUS
DTCP-IP
One-to-One
(for USB Rec.)
Netflix
Widewine
HDCP
TX-L50ET60B Yes
Yes None Yes Yes
TX-L50ET60Y Yes
Yes None Yes Yes
TX-LR50ET60 Yes
None None Yes Yes
11
Setting Inspection
Voltage Confirmation
A board
Description Test
point
Voltage
PANEL12V
TP4000 / TP4001
11.5V – 12.5V
SUB5V TP0900
4.95V - 5.4V
SUB3.3V
TP5400
3.17V – 3.43V
SUB1.8V
TP8714
1.70V – 1.90V
SUB 1.5 V
TP8100
1.435V - 1.585V
SUB1.2V
TP8101
1.14V - 1.26V
USB5V
TP5440
4.94V – 5.40V
DMD_1.2/1.1V
TP5703
1.1V – 1.21V
P board
Description Test
point
Voltage*
Voltage**
24V (PANEL)
TP7407 and GND TP7414
<1V
24V ± 1.2V
16V
TP7410 and GND TP7414
<1V
15.7V ± 0.6V
5VS
TP7501 and GND TP7414
5.3V ± 0.2V
5.3V ± 0.2V
PFC
TP7201 and GND TP7203***
<340V
390V ± 15V
* Connect AC 230V to JK7101 connector
** Connect DC 2.5V to TV_SUB_ON P2 connector – pin 8 /TP7416/ from voltage divider.
***Beware, for testing of PFC use the GND (TP7203) in Hot area of P board – risk of electric shock!
12
Click on the first or last page to see other TX-L50ET60B / TX-L50ET60Y / TX-LR50ET60 service manuals if exist.