Panasonic TX-42AR400 Service Manual ▷ View online
TX-42AR400
7
4 Specifications
Note
• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
Power source
AC 220 - 240 V, 50/60 Hz
Power consumption
91 W / 0.35 W
(Rate power / Standby power)
Display panel
Panel
LCD panel (LED backlight)
Visible screen size (diagonal)
106 cm
Display Resolution
1,920 (W)
1,080 (H)
Dimensions (W
H D)
963 mm
610 mm 247 mm (With Pedestal)
963 mm
566 mm 69 mm (TV only)
Mass
10.0 (With Pedestal)
8.5 (TV only)
8.5 (TV only)
Connection terminals
AV1
SCART (Audio/Video in, Audio/Video out, RGB in)
AV2 (COMPONENT / VIDEO)
VIDEO
RCA PIN Type
1, 1.0 V[p-p] (75 )
AUDIO L - R
RCA PIN Type
2, 0.5 V[rms]
Y
1.0 V[p-p] (including synchronisation)
P
B
, P
R
±0.35 V[p-p]
HDMI 1 / 2 input
TYPE A Connectors
USB
USB 2.0 TYPE A Connectors
DC 5 V, Max. 500 mA
DC 5 V, Max. 500 mA
Card slot
Common Interface slot (complies with CI Plus)
1
DIGITAL AUDIO
PCM / Dolby Digital / DTS, Fibre optic
Sound
Audio output
20 W (10 W + 10 W)
Headphones
M3 (3.5 mm) stereo mini Jack
1
Receiving systems / Band name
Check the latest information on the
Check the latest information on the
DVB-C
Digital cable services (MPEG2 and MPEG4-AVC(H.264))
available services at the following web
DVB-T / T2
Digital terrestrial services (MPEG2 and MPEG4-AVC(H.264))
site. (English only)
PAL D, K
http://panasonic.net/viera/support
SECAM D, K
VHF R1 - R2
VHF R3 - R5
VHF R6 - R12
UHF E21 - E69
VHF R6 - R12
UHF E21 - E69
PAL 526/60
Playback of NTSC tape from some PAL Video recorders (VCR)
M.NTSC
Playback from M.NTSC Video recorders (VCR)
NTSC (AV input only)
Playback from NTSC Video recorders (VCR)
Aerial input
VHF / UHF
Operating Conditions
Temperature
0 °C - 35 °C
Humidity
20% - 80% RH (non-condensing)
TX-42AR400
8
5 Service Mode
5.1.
How to enter into Service Mode
5.1.1.
Purpose
After exchange parts, check and adjust the contents of adjustment mode.
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
5.1.2.
Key command
[1] button...Main items Selection in forward direction
[2] button...Main items Selection in reverse direction
[3] button...Sub items Selection in forward direction
[4] button...Sub items Selection in reverse direction
[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
[2] button...Main items Selection in reverse direction
[3] button...Sub items Selection in forward direction
[4] button...Sub items Selection in reverse direction
[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
5.1.3.
How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
5.1.4.
Contents of adjustment mode
• Value is shown as a hexadecimal number.
• Preset value differs depending on models.
• After entering the adjustment mode, take note of the value in each item before starting adjustment.
• Preset value differs depending on models.
• After entering the adjustment mode, take note of the value in each item before starting adjustment.
Main item
Sub item
Sample Data
ADJUST
H POS
H AMP
V POS
V AMP
V COM
H AMP
V POS
V AMP
V COM
WB-ADJ
R-GAIN
8D
G-GAIN
AE
B-GAIN
FF
R-CENT
6C
G-RENT
80
B-CENT
A0
OPTION
Boot upgrade
NO
STBY-SET
00
EMERGENCY
ON
CLK MODE
00
CLOCK
FC7
Y/C DELAY
DYNAMIC
OPT 1
00000000
OPT 2
11100110
OPT 3
00001001
OPT 4
00000000
EDID-CLK
HIGH
TX-42AR400
9
5.1.5.
Display of SOS History
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory
shipment setting].
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory
shipment setting].
5.1.6.
Exit
1. Disconnect the AC cord from wall outlet.
5.1.7.
Hotel Mode
1. Purpose
Restrict a function for hotels.
2. Access command to the Hotel mode setup menu.
In order to display the Hotel mode setup menu:
While pressing [VOLUME (-)] button of the main unit,
press [AV] button of the remote control three times within
2 seconds.
While pressing [VOLUME (-)] button of the main unit,
press [AV] button of the remote control three times within
2 seconds.
Then, the Hotel mode setup menu is displayed.
3. To exit the Hotel mode setup menu
Disconnect AC power cord from wall outlet.
4. Explain the Hotel mode setup menu
Item
Function
Hotel Mode
Select hotel mode On/Off
Initial INPUT
Select input signal modes.
Set the input, when each time power is switched on.
Selection :
Off,Analogue,DVB-C,DVB-T,AV1,AV2,HDMI1,
HDMI2
Set the input, when each time power is switched on.
Selection :
Off,Analogue,DVB-C,DVB-T,AV1,AV2,HDMI1,
HDMI2
• Off: give priority to a last memory. However, Euro
model is compulsorily set to TV.
Initial POS
Select programme number.
Selection :
Off/0 to 99
Selection :
Off/0 to 99
• Off: give priority to a last memory.
Initial VOL LEVEL
Adjust the volume when each time power is switched
on.
Selection Range :
Off/0 to 100
on.
Selection Range :
Off/0 to 100
• Off: give priority to a last memory.
Maximum Vol Level Adjust maximum volume.
Range :
0 to 100
0 to 100
Button Lock
Select local key conditions.
Selection :
Off/SETUP/MENU/ALL
Selection :
Off/SETUP/MENU/ALL
• OFF: altogether valid
• SETUP: only F-key is invalid
• SETUP: only F-key is invalid
(Tuning guide (menu) can not be selected.)
• MENU: only F-key is invalid
(only Volume/Mute can be selected.)
• ALL: altogether invalid.
Remote Lock
Select remote control key conditions.
Selection :
Off/SETUP/MENU
Selection :
Off/SETUP/MENU
• OFF: altogether valid.
• SETUP: only Setup menu is invalid.
• MENU: Picture/Sound/Setup menu are invalid.
• SETUP: only Setup menu is invalid.
• MENU: Picture/Sound/Setup menu are invalid.
Hotel Mode USB
Basically after user already setup the hotel mode
according to their criteria, what they need to do is
according to their criteria, what they need to do is
• insert USB (while in hotel mode)
• choose ‘Copy TV to USB’ to copy the setting into
• choose ‘Copy TV to USB’ to copy the setting into
the USB (a file will be created to store the hotel
mode setting in the USB)
mode setting in the USB)
• switch ‘OFF’ the unit
• pull out USB from unit
• pull out USB from unit
To copy the hotel mode setting from USB.
• enter hotel mode
• insert USB
• choose ‘Copy USB to TV’
• follow instruction as shown on the units
• once finish, switch ‘OFF; the unit
• pull out USB from unit
• insert USB
• choose ‘Copy USB to TV’
• follow instruction as shown on the units
• once finish, switch ‘OFF; the unit
• pull out USB from unit
Private Information Select private information for VIERA Cast is Keep or
Reset if Hotel mode is set to [On] when TV power on
Selection :
Keep/Reset
Selection :
Keep/Reset
• Keep: private information for VIERA Cast is keep
• Reset: private information for VIERA Cast is
• Reset: private information for VIERA Cast is
reset
TX-42AR400
10
6 Troubleshooting Guide
Use the self-check function to test the unit.
1. Checking the IIC bus lines
2. Power LED Blinking timing
2. Power LED Blinking timing
6.1.
Check of the IIC bus lines
6.1.1.
How to access
6.1.2.
Self-check indication only
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control
for more than 3 seconds.
for more than 3 seconds.
6.1.3.
Self-check indication and forced to factory shipment setting
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote
control for more than 3 seconds.
control for more than 3 seconds.
6.1.4.
Exit
Disconnect the AC cord from wall outlet.
6.1.5.
Screen display
Click on the first or last page to see other TX-42AR400 service manuals if exist.