Panasonic TX-37LZ70P / TX-R37LZ70 Service Manual ▷ View online
Service Manual
Colour LCD Television
TX-37LZ70P
TX-R37LZ70
LH64 Chassis
Specifications
Power
Source:
220-240V AC, 50/60Hz
Power Consumption
188W
Stand-by Power Consumption: 0.4W
Aerial
Impedance: 75
Ω unbalanced, Coaxial Type
Receiving
System:
PAL-I/H, B/G, D/K,
SECAM B/G, D/K, L/L’
PAL-525/60 (AV only)
M.NTSC
(AV
only)
NTSC (AV only)
Receiving
Channels: VHF
E2-E12
VHF H1-H2 (ITALY)
VHF A-H (ITALY) VHF R1-R2
VHF R3-R5 VHF R6-R12
UHF E21-E69 CATV (S01-S05)
CATV S1-S10 (M1-M10) CATV S11-S20 (U1-U10)
CATV S21-S41 (Hyperband)
Operating Conditions:
Temperature: 0°C
÷ 35°C
Humidity: 20%
÷ 80% RH (non condensing)
Scanning format:
480i(60Hz), 480p(60Hz), 576i(50Hz), 576p(50Hz), 720p(60Hz), 720p(50Hz), 1.080i(60Hz),
1.080i(50Hz), 1.080p(60Hz), 1.080p(50Hz), 1.080p(24Hz)
PC
signals:
VGA, SVGA, XGA, SXGA(compressed)
Horizontal scanning frequency
Horizontal scanning frequency
31 – 69 kHz
Vertical scanning frequency
59 – 86 Hz
ORDER No. PCZ0709108CE
Intermediate Frequency:
Video/Audio
Video
38,9MHz,
33,9MHz
Audio
33,4MHz (B/G), 33,16MHz (A2)
33,05MHz (NICAM B/G, D/K, L)
32,4MHz (D/K), 32,66MHz (CZ STEREO)
40,4MHz
(L
’
), 39,75MHz (L
’
NICAM)
Colour
34,47MHz
(PAL)
34,5MHz, 34,65MHz (SECAM)
38,3MHz, 38,15MHz (SECAM L
’
)
Terminals:
AV1 IN
Video (21 pin) 1V p-p 75
Ω
Audio (21 pin) 500mV rms 10k
Ω
RGB (21 pin) 0,7V p-p 75
Ω
AV1 OUT
Video (21 pin) 1V p-p 75
Ω
Audio (21 pin) 500mV rms 1k
Ω
AV2 IN
Video (21 pin) 1V p-p 75
Ω
Audio (21 pin) 500mV rms 10k
Ω
RGB (21 pin) 0,7V p-p 75
Ω
S-video IN (21-pin) Y: 1V p-p 75
Ω
C:0,3V
p-p
75
Ω
AV2 OUT
Video (21 pin) 1V p-p 75
Ω
Audio (21 pin) 500mV rms 1k
Ω
AV3 IN
S-Video IN (4-pin) Y: 1V p-p 75
Ω
C:0,3V
p-p
75
Ω
Audio
(RCAx2)
500mV rms 10k
Ω
Video
(RCAx1)
1V p-p 75
Ω
HDMI1, HDMI2
Type A Connector
COMPONENT
Video
(RCAx3)
Y:1V p-p 75
Ω (including synchronization)
Pb, Pr: ±0,35V p-p 75
Ω
AUDIO IN
Audio (RCAx2) 500mV rms 10k
Ω (for YUV, HDMI1)
AUDIO
OUT
Audio
(RCAx2)
500mV rms 1k
Ω (high impedance)
CARD SLOT
SD CARD slot x1
PC
HIGH-DENSITY D_SUB 15PIN R,G,B: 700mV p-p 75
Ω
HD,VD/TTL Level 2-5V p-p (high impedance)
LCD
screen:
L5EDD9T00002
1920 x 1080 XGA, 16:9
Visible Diagonal 940mm
Audio
Output:
20W (2x10W)
Headphones:
3,5mm,
8
Ω Impedance
Accessories supplied :
Remote Control
2 x R6 (UM3) Batteries
Dimensions:
Height: Width: Depth:
Including TV stand
634mm 1031mm 300mm
TV set only
588mm 1031mm 120mm
Net
weight:
27kg
Specifications are subject to change without notice.
Weights and dimensions shown are approximate.
This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not
contain warnings or cautions to advise non-technical individuals of potencial dangers in attempting to service a product. Products
powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the
product or products deal within this service information by anyone else could result in serious injury or death.
contain warnings or cautions to advise non-technical individuals of potencial dangers in attempting to service a product. Products
powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the
product or products deal within this service information by anyone else could result in serious injury or death.
Warning
2
CONTENTS
SAFETY PRECAUTIONS ........................................... 4
GENERAL
GUIDE LINES...................................... 4
TOUCH – CURRENT CHECK............................... 4
PREVENTION OF ELECTROSTATIC DISCHARGE
(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)
DEVICES .................................................................... 5
ABOUT LEAD FREE SOLDER (PBF)......................... 6
SUGGESTED
PB
FREE SOLDER........................ 6
APPLICABLE SIGNALS.............................................. 7
SERVICE HINTS ........................................................ 8
CHASSIS BOARD LAYOUT ....................................... 9
LOCATION OF LEAD WIRING………………………… 9
SETTING INSPECTION............................................ 10
SELF-CHECK ........................................................... 11
POWER LED BLINKING TIMING CHART ................ 12
SERVICE MODE FUNCTION ................................... 13
SERVICE ................................................................. 14
OPTION BYTES DESCRIPTION .............................. 15
ADJUSTMENT METHOD ......................................... 16
WIRING DIAGRAM ................................................... 17
BLOCK DIAGRAMS.................................................. 18
PARTS LOCATION................................................... 21
REPLACEMENT PARTS LIST.................................. 23
SCHEMATIC DIAGRAMS......................................... 45
AP-BOARD (1 OF 2) SCHEMATIC DIAGRAM.... 46
AP-BOARD (2 OF 2) SCHEMATIC DIAGRAM.... 47
DG-BOARD (1 OF 15) SCHEM. DIAGRAM ........ 48
DG-BOARD (2 OF 15) SCHEM. DIAGRAM ........ 49
DG-BOARD (3 OF 15) SCHEM. DIAGRAM ........ 50
DG-BOARD (4 OF 15) SCHEM. DIAGRAM ........ 51
DG-BOARD (5 OF 15) SCHEM. DIAGRAM ........ 52
DG-BOARD (6 OF 15) SCHEM. DIAGRAM ........ 53
DG-BOARD (7 OF 15) SCHEM. DIAGRAM ........ 54
DG-BOARD (8 OF 15) SCHEM. DIAGRAM ........ 55
DG-BOARD (9 OF 15) SCHEM. DIAGRAM ........ 56
DG-BOARD (10 OF 15) SCHEM. DIAGRAM ...... 57
DG-BOARD (11 OF 15) SCHEM. DIAGRAM ...... 58
DG-BOARD (12 OF 15) SCHEM. DIAGRAM ...... 59
DG-BOARD (13 OF 15) SCHEM. DIAGRAM ...... 60
DG-BOARD (14 OF 15) SCHEM. DIAGRAM ...... 61
DG-BOARD (15 OF 15) SCHEM. DIAGRAM ...... 62
H-BOARD (1 OF 5) SCHEMATIC DIAGRAM ...... 63
H-BOARD (2 OF 5) SCHEMATIC DIAGRAM ...... 64
H-BOARD (3 OF 5) SCHEMATIC DIAGRAM ...... 65
H-BOARD (4 OF 5) SCHEMATIC DIAGRAM...... 66
H-BOARD (5 OF 5) SCHEMATIC DIAGRAM ...... 67
G-BOARD
SCHEMATIC DIAGRAM .................... 68
GS-BOARD
SCHEMATIC DIAGRAM.................. 69
S-BOARD
SCHEMATIC DIAGRAM .................... 70
R-BOARD
SCHEMATIC DIAGRAM .................... 71
V-BOARD SCHEMATIC DIAGRAM .................... 72
CONDUCTOR VIEWS .............................................. 73
3
Safety Precautions
General Guide Lines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated
or damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following touch current checks to prevent the customer from being exposed to shock hazards.
4. Always ensure panel TKP0E16001
4. Always ensure panel TKP0E16001
is correctly replaced before returning to customer (see Fig.1).
Touch-Current Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth
2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth
ground such as a water pipe, as shown in Fig. 2.
3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reserve the AC plug in the AC outlet and repeat each of the above measure.
6. The potential at any point (TOUCH CURRENT) expressed as voltage U1 and U2, does not exceed the following values:
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reserve the AC plug in the AC outlet and repeat each of the above measure.
6. The potential at any point (TOUCH CURRENT) expressed as voltage U1 and U2, does not exceed the following values:
For a. c.: U1 = 35 V (peak) and U2 = 0.35 V (peak);
For d. c.: U1 = 1.0 V,
For d. c.: U1 = 1.0 V,
Note:
The limit value of U2 = 0.35 V (peak) for a. c. and U1 = 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and
2.0 mA d. c.
The limit value U1 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100
kHz.
2.0 mA d. c.
The limit value U1 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100
kHz.
7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should
be repaired and rechecked before it is returned to the customer.
Fig. 2
Fig. 1
4
TO
APPLIANCES
EXPOSED
METAL PARTS
APPLIANCES
EXPOSED
METAL PARTS
Resistance values in ohms (
Ω)
V
R
0
=500
Ω
R
S
=1500
Ω
C
S
=0.22
μF
10k
Ω
0.022
μF
U
1
COLD
WATER PIPE
(EARTH GROUND)
WATER PIPE
(EARTH GROUND)
V: Voltmetr or oscilloscope
(r.m.s. or peak reading)
(r.m.s. or peak reading)
Measuring network for TOUCH CURRENTS
Input resistance:
≥ 1MΩ
Input capacitance:
≤ 200pF
Frequency range: 15Hz to 1MHz and d.c.respectively
NOTE – Appropriate measures should be taken to obtain the correct value in case of non-sinusoidal waveforms
U
2
(V)