DOWNLOAD Panasonic TX-37LX85F / TX-37LX85L / TX-37LX85P / TX-32LX85F / TX-32LX85L / TX-32LX85P / TX-R37LX85 / TX-R32LX85 Service Manual ↓ Size: 16.41 MB | Pages: 70 in PDF or view online for FREE

Service Manual

(Informations in brackets [ ] refers to model 32”)

220-240V AC, 50Hz

180W [140W]

Stand-by Power Consumption: 0.4W

         75

Ω unbalanced, Coaxial Type

PAL-I/H, B/G, D/K

 

SECAM B/G, D/K, L/L’
PAL-525/60 (AV only)
M.NTSC (AV only)
NTSC (AV only)

VHF E2-E12

VHF H1-H2 (ITALY)

VHF A-H (ITALY)

VHF R1-R2

VHF R3-R5

VHF R6-R12

UHF E21-E69

CATV (S01-S05)

CATV S1-S10 (M1-M10)

CATV S11-S20 (U1-U10)

CATV S21-S41 (Hyperband)

            Operating Conditions:

Temperature:

0°C 

÷ 35°C

Humidity:   20% 

÷ 80% RH (non condensing)

480i(60Hz), 480p(60Hz), 576i(50Hz), 576p(50Hz), 720p(60Hz), 720p(50Hz), 1.080i(60Hz),
1.080i(50Hz), 1.080p(60Hz), 1.080p(50Hz) ), 1.080p(24Hz)

  

VGA, SVGA, XGA, SXGA(compressed)
Horizontal scanning frequency

31 – 69 kHz

Vertical scanning frequency

59 – 86 Hz

ORDER No. PCZ0804035CE

WILLOUGHBY ROAD,

BRACKNELL,

BERKS.,

RG12 8FT.

Video

38,9MHz, 33,9MHz

Audio

33,4MHz (B/G), 33,16MHz (A2)
33,05MHz (NICAM B/G, D/K, L’)
32,4MHz (D/K), 32,66MHz (CZ STEREO)
40,4MHz (L’), 39,75MHz (L’ NICAM)

Colour

34,47MHz (PAL)
34,5MHz, 34,65MHz (SECAM)
38,3MHz, 38,15MHz (SECAM L’)

            Terminals:

AV1 IN

Video (21 pin) 1V p-p 75

Ω

Audio (21 pin) 500mV rms 10k

Ω

RGB (21 pin) 0,7V p-p 75

Ω

AV1 OUT

Video (21 pin) 1V p-p 75

Ω

Audio (21 pin) 500mV rms 1k

Ω

AV2 IN

Video (21 pin) 1V p-p 75

Ω

Audio (21 pin) 500mV rms 10k

Ω

RGB (21 pin) 0,7V p-p 75

Ω

S-video IN (21-pin)Y: 1V p-p 75

Ω

C:0,3V p-p 75

Ω

AV2 OUT

Video (21 pin) 1V p-p 75

Ω

Audio (21 pin) 500mV rms 1k

Ω

AV3 IN

S-Video IN (4-pin) Y: 1V p-p 75

Ω

                             C:0,286V p-p 75

Ω

Audio (RCAx2) 500mV rms 10k

Ω

Video (RCAx1) 1V p-p 75

Ω

HDMI1, HDMI2, HDMI3

Type A Connector

COMPONENT 

Video (RCAx3) Y:1V p-p 75

Ω (including synchronization)

Pb, Pr: ±0,35V p-p 75

Ω

AUDIO IN

Audio (RCAx2) 500mV rms 10k

Ω (for YUV; HDMI1)

AUDIO OUT

Audio (RCAx2) 500mV rms 1k

Ω (high Impedance) 

CARD SLOT                                 SD CARD slot 

×1

PC

HIGH-DENSITY D_SUB 15PIN  R,G,B: 700mV p-p 75

Ω

HD,VD:TTL Level 2-5V p-p (high impedance)

L5EDD9Q00004     [L5EDD8Q00040]
1366 x 768 XGA, 16:9
Visible Diagonal 940mm    [800mm]

20W (2x10W)

3,5mm (M3), 8

Ω Impedance

Remote Control

2 x R6 (UM3) Batteries

Height:

Width:

Depth:

Including TV stand

645mm

940mm 

294mm

[572mm]

[820mm] [250mm]

TV set only

605mm

940mm  

120mm

[534mm]

[820mm] [119mm]

             Including TV stand                        21.0kg

[17.0kg]

             TV set only                                   

 17.5kg        [14.0kg]

            Specifications are subject to change without notice.

Weights and dimensions shown are approximate.

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not
contain warnings or cautions to advise non-technical individuals of potencial dangers in attempting to service a product. Products
powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the
product or products deal within this service information by anyone else could result in serious injury or death.

PREVENTION OF ELECTROSTATIC DISCHARGE (ESD)

1.  When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated

or damaged by the short circuit.

2.    After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
       installed.
3.    After servicing, make the following touch current checks to prevent the customer from being exposed to shock hazards.
4.    Always ensure panel TKP0E16001 is correctly replaced before returning to customer (see Fig.1).

1.  Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2.  Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth

ground such as a water pipe, as shown in Fig. 2.

3.  Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4.  Check each exposed metallic part, and measure the voltage at each point.
5.  Reserve the AC plug in the AC outlet and repeat each of the above measure.
6.  The potential at any point (TOUCH CURRENT) expressed as voltage U1 and U2, does not exceed the following values:

For a. c.: U1 = 35 V (peak) and U2 = 0.35 V (peak);
For d. c.: U1 = 1.0 V,
Note:
The limit value of U2 = 0.35 V (peak) for a. c. and U1 = 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and
2.0 mA d. c.
The limit value U1 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100
kHz.

7.  In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should

be repaired and rechecked before it is returned to the customer.

TO
APPLIANCES
EXPOSED
METAL PARTS

Resistance values in ohms (

Ω)

V

R

0

=500

Ω

R

S

=1500

Ω

C

S

=0.22

μF

10k

Ω

0.022

μF

U

1

COLD
WATER PIPE
(EARTH GROUND)

V: Voltmetr or oscilloscope

(r.m.s. or peak reading)

Measuring network for TOUCH CURRENTS

Input resistance: 

≥ 1MΩ

Input capacitance:

 ≤ 200pF

Frequency range: 15Hz to 1MHz and d.c.respectively

NOTE – Appropriate measures should be taken to obtain the correct value in case of non-sinusoidal waveforms

U

2

 (V)