Panasonic TX-36PD50D / TX-36PD50F / TX-36PD50P / TX-32PD50D / TX-32PD50F / TX-32PD50P Service Manual ▷ View online
Description
Cct Ref
Parts Number
Description
Cct Ref
Parts Number
UNDER DECORATION
.
TKPA69405
GEOMAGNETIC COIL
.
TLK8E05191
CARTON
.
TPC8E5073
TOP CUSHION
.
TPD8E799
BOTTOM CUSHION
.
TPD8E800
SUB CUSHION
.
TPD8E801
INSTRUCTION BOOKS
GERMAN/SPANISH
TQB8E4091AE
DUTCH/FRENCH
TQB8E4091BD
SWEDISH/NORWEGIAN
TQB8E4091FG
FINNISH(SUOMI)/DANISH
TQB8E4091HK
I.C.s
EAROM*
IC1007
X24C1400-1DF
RESISTORS
METAL
R533
ERG3FJS821D
3W
5%
820 Ω
METAL
R587
EROS2THF1502
0.25W
1%
15K Ω
CAPACITORS
FILM
C851
ECQE2154JF3
250V
150nF
DIFFERENCES FOR MODEL TX--36PD50FP
EXPLODED VIEW
A P.C.B.
17
TNPH0525AU
ANODE CABLE
18
ZTBZAD650E
BACKCOVER
19
TKUC13802
C.R.T.
20
W86LXK005X01
CABINET
21
TKYA21002
CHASSIS FRAME
22
TMX8E050
D P.C.B.
23
TNPH0526AB
DEGAUSS COIL
24
TLK8E05192
DF P.C.B.
25
TNPA3005AB
MODEL LABEL
26
TQF8E3528
MISCELLANEOUS COMPONENTS
SUB WOOFER
EAB10108B2
SP PANEL L
.
TKPA67702
SP PANEL R
.
TKPA67802
SIDE DECORATION
.
TKPA68403
SIDE DECORATION
.
TKPA68503
UNDER DECORATION
.
TKPA69305
UNDER DECORATION
.
TKPA69405
GEOMAGNETIC COIL
.
TLK8E05191
CARTON
.
TPC8E5073
TOP CUSHION
.
TPD8E799
BOTTOM CUSHION
.
TPD8E800
SUB CUSHION
.
TPD8E801
INSTRUCTION BOOKS
BULGARIAN/ROMANIAN
TQB8E4089MN
POLISH/HUNGARIAN
TQB8E4089PQ
CZECH/ENGLISH
TQB8E4089RU
I.C.s
EAROM*
IC1007
X24C1400-1DP
RESISTORS
METAL
R533
ERG3FJS821D
3W
5%
820 Ω
METAL
R587
EROS2THF1502
0.25W
1%
15K Ω
CAPACITORS
FILM
C851
ECQE2154JF3
250V
150nF
37
SCHEMATIC DIAGRAMS FOR MODELS
TX-32/36PD50D
TX-32/36PD50F
TX-32/36PD50F/P
(GP1 CHASSIS)
NOTE
1. RESISTOR
All resistors are carbon ¼W resistor, unless marked otherwise.
Unit of resistance is OHM (
Unit of resistance is OHM (
Ω
) (K=1,000, M=1,000,000)
2. CAPACITORS
All capacitors are ceramic 50V unless marked otherwise.
Unit of capacitance is
Unit of capacitance is
µ
F unless otherwise stated.
3. COIL
Unit of inductance is
µ
H, unless otherwise stated.
4. TEST
POINT
Test Point Position
5. EARTH
SYMBOL
Chassis Earth (Cold)
Line Earth (Hot)
6. VOLTAGE
MEASUREMENT
Voltage is measured by a d.c. voltmeter.
Measurement conditions are as follows:
Power source
Measurement conditions are as follows:
Power source
a.c. 220V-240V, 50Hz
Receiving Signal
Colour Bar signal (RF)
All customer controls
Maximum position
7.
Indicates the Video signal path
Indicates the Audio signal path
These schematic diagrams are the latest at time of printing and are subject to change without notice.
REMARKS
a. Do not touch the hot part, or the hot and cold parts at the same time, as you are liable to a shock hazard.
b. Do not short circuit the hot and cold circuits as electrical components may be damaged.
c.
Do not connect an instrument, such as an oscilloscope, to the hot and cold circuits simultaneously as this may cause
fuse failure. Connect the earth of the instruments to the earth connection of the circuit being measured.
fuse failure. Connect the earth of the instruments to the earth connection of the circuit being measured.
d. Make sure to disconnect the power plug before removing the chassis.
NOTE
1. The Power Supply Circuit contains a circuit area, which uses a separate power supply to isolate the earth connection.
The circuit is defined by HOT and COLD indications in the schematic diagram. All circuits, except the Power Circuit, are
COLD.
COLD.
IMPORTANT SAFETY NOTICE
Components identified by
mark have special characteristics
important for safety. When replacing any of these components, use
only manufacturer's specified parts.
only manufacturer's specified parts.
38
Click on the first or last page to see other TX-36PD50D / TX-36PD50F / TX-36PD50P / TX-32PD50D / TX-32PD50F / TX-32PD50P service manuals if exist.