Panasonic TX-32PS11D / TX-32PS11B / TX-32PS11F / TX-32PS11P / TX-29PS11D / TX-29PS11B / TX-29PS11F / TX-29PS11P / TX-28PS11D / TX-28PS11F Service Manual ▷ View online
CONTENTS
SAFETY PRECAUTIONS ......................................................................................................................................................... 2
SERVICE HINTS ...................................................................................................................................................................... 3
ADJUSTMENT PROCEDURE AND SELF-CHECK .................................................................................................................. 4
WAVEFORM PATTERN TABLE............................................................................................................................................... 5
ALIGNMENT SETTINGS .......................................................................................................................................................... 6
BLOCK DIAGRAMS.................................................................................................................................................................. 7
PARTS LOCATION................................................................................................................................................................. 12
REPLACEMENT PARTS LIST................................................................................................................................................ 13
SCHEMATIC DIAGRAMS....................................................................................................................................................... 27
CONDUCTOR VIEWS ............................................................................................................................................................ 30
SAFETY PRECAUTION
GENERAL GUIDE LINES
1. It is advisable to insert an isolation transformer in the
a.c. supply before servicing a hot chassis.
2. When servicing, observe the original lead dress in the
high voltage circuits. If a short circuit is found, replace
all parts that have been overheated or damaged by
the short circuit.
all parts that have been overheated or damaged by
the short circuit.
3. After servicing, see that all the protective devices
such as insulation barriers, insulation papers, shields
and isolation R-C combinations are correctly
installed.
and isolation R-C combinations are correctly
installed.
4. When the receiver is not being used for a long period
of time, unplug the power cord from the a.c. outlet.
5. Potentials as high as 33kV [32kV] {31,5kV} are
present when this receiver is in operation. Operation
of the receiver without the rear cover involves the
danger of a shock hazard from the receiver power
supply. Servicing should not be attempted by anyone
who is not familiar with the precautions necessary
when working on high voltage equipment. Always
discharge the anode of the tube.
of the receiver without the rear cover involves the
danger of a shock hazard from the receiver power
supply. Servicing should not be attempted by anyone
who is not familiar with the precautions necessary
when working on high voltage equipment. Always
discharge the anode of the tube.
6. After servicing make the following leakage current
checks to prevent the customer from being exposed
to shock hazard.
to shock hazard.
LEAKAGE CURRENT COLD CHECK
1. Unplug the a.c. cord and connect a jumper between
the two prongs of the plug.
2. Turn on the receiver’s power switch.
3. Measure the resistance value with an ohmmeter,
3. Measure the resistance value with an ohmmeter,
between the jumpered a.c. plug and each exposed
metallic cabinet part on the receiver, such as screw
heads, aerials, connectors, control shafts etc. When
the exposed metallic part has a return path to the
chassis, the reading should be between 4M ohm and
20M ohm. When the exposed metal does not have a
return path to the chassis, the reading must be
infinite.
metallic cabinet part on the receiver, such as screw
heads, aerials, connectors, control shafts etc. When
the exposed metallic part has a return path to the
chassis, the reading should be between 4M ohm and
20M ohm. When the exposed metal does not have a
return path to the chassis, the reading must be
infinite.
LEAKAGE CURRENT HOT CHECK
1. Plug the a.c. cord directly into the a.c. outlet. Do not
use an isolation transformer for this check.
2. Connect a 2k
Ω 10W resistor in series with an
exposed metallic part on the receiver and an earth,
such as a water pipe.
such as a water pipe.
3. Use an a.c. voltmeter with high impedance to
measure the potential across the resistor.
4. Check each exposed metallic part and check the
voltage at each point.
5. Reverse the a.c. plug at the outlet and repeat each of
the previous measurements.
6. The potential at any point should not exceed
1,4 Vrms. In case a measurement is outside the limits
specified, there is a possibility of a shock hazard, and
the receiver should be repaired and rechecked before
it is returned to the customer.
specified, there is a possibility of a shock hazard, and
the receiver should be repaired and rechecked before
it is returned to the customer.
X-RADIATION WARNING
1. The potential sources of X-Radiation in TV sets are
the high voltage section and the picture tube.
2. When using a picture tube test jig for service, ensure
that the jig is capable of handling 33kV [32kV]
{31,5kV} without causing X-Radiation.
{31,5kV} without causing X-Radiation.
NOTE
: It is important to use an accurate periodically
calibrated high voltage meter.
1. Set the brightness to minimum.
2. Measure the high voltage. The meter should indicate:
1. Set the brightness to minimum.
2. Measure the high voltage. The meter should indicate:
32kV ± 1kV [31kV ± 1kV] {30,5kV ± 1kV}.
If the meter indication is out of tolerance, immediate
service and correction is required to prevent the
possibility of premature component failure.
service and correction is required to prevent the
possibility of premature component failure.
3. To prevent any X-Radiation possibility, it is essential
to use the specified tube.
HOT CHECK CIRCUIT
a.c. VOLTMETER
WATER PIPE
(EARTH)
TO INSTRUMENT'S EXPOSED
METALLIC PARTS
METALLIC PARTS
Fig. 1.
2kΩ 10 Watts
2
SERVICE HINTS
How to remove the rear cover
1. Remove the 12 [11] screws as shown in
Fig.2.
LOCATION OF CONTROLS
3
Fig. 2
Fig. 3
SCREWS
SCREWS
L-Board
A-Board
Focus
G-Board
Screen D-Board
ADJUSTMENT PROCEDURE
Item / Preparation
Adjustments
+B SET-UP
1. Receive a Window pattern.
2. Set the controls :
2. Set the controls :
Brightness
Minimum
Contrast
Minimum
Volume
Minimum
Confirm the following voltages:
TPD1
205
± 10V
D9 pin3
9
± 0,5V
TPD2
137
± 2V
D9 pin7
10,5
± 0,5V
TPD3
42
± 2V
D2 pin22 3,3
± 0,1V
TPD5
42
± 2V
D2 pin26 2,5 ± 0,1V
TPD6
12,5
± 1V
D2 pin14 3,3 ± 0,1V
TPD7
-12,5 ± 1V
D9 pin5
5
± 0,5V
TPD8
33
± 2V
D9 pin11 6,5
± 0,5V
TPD11
5
± 0,5V
CUT OFF / Ug2 Test
1. Receive a Window pattern.
2. Set Viewing Mode: Normal
3. Normalize the TV set.
4. Set brightness: Minimum
2. Set Viewing Mode: Normal
3. Normalize the TV set.
4. Set brightness: Minimum
To adjust Cutoff connect an oscilloscope to the Blue cathode. Adjust
the screen VR until the black level is 160V +5V/-5V.
the screen VR until the black level is 160V +5V/-5V.
SELF CHECK
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set.To enter Self-Check mode, press
the STATUS button on the remote control and at the same time press the down (-/v) button on the customer controls at
the front the TV set. To exit Self Check, switch off the TV set at the power button.
the STATUS button on the remote control and at the same time press the down (-/v) button on the customer controls at
the front the TV set. To exit Self Check, switch off the TV set at the power button.
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
4
E2
O.K.
DDP
O.K.
VSP
O.K.
VPCD
O.K.
AVSW
O.K.
TUN
O.K.
MSP
O.K.
DPL
---
MAS
---
SUM
****
TX-32PS11D
TX-32PS11F
TX-29PS11D
TX-29PS11F
TX-32PS11D/B
TX-32PS11P
TX-29PS11D/B
TX-29PS11P
TX-28PS11D
TX-28PS11F
OPTION 1
0F
0F
0F
0F
OPTION 2
00
00
00
00
OPTION 3
B0
B0
A0
A0
OPTION 4
11
11
11
11
OPTION 5
00
00
00
00
OPTION 6
05
05
05
05
OPTION 7
7F
7F
7F
7F
OPTION 8
D0
50
D0
50
OPTION 9
00
00
00
00
OPTION 10
80
80
80
80
OPTION 11
1B
1B
1B
1B
OPTION 12
00
00
00
00
OPTION 13
0C
0C
0C
0C
CHECK
CB
4B
BB
3B
Black Level
160V+5V/-5V
GND
WAVEFORM PATTERN TABLE
5
CONDITIONS:
CONTRAST...MAX, BRIGHTNESS...MID, COLOUR...MID, SHARPNESS...MID