DOWNLOAD Panasonic TX-32DK10F Service Manual ↓ Size: 13.25 MB | Pages: 43 in PDF or view online for FREE

Model
TX-32DK10F
Pages
43
Size
13.25 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / EURO-5
File
tx-32dk10f.pdf
Date

Panasonic TX-32DK10F Service Manual ▷ View online

HOT CHECK CIRCUIT
2k ohm
a.c.. VOLTMETER
Water Pipe
    (Earth)
TO INSTRUMENT’S
EXPOSED
METALLIC PARTS
SCHALTUNGSAUFBAU FÜR PRUFUNG
IM EINGESCHALTETEN ZUSTAND
WECHSELSTROM-VOLTMETER
AN ZUGANGLICHE
METALLTEILE DAS
TV-GERATES
Wasserleitung
    (Erdung)
Fig. 1.
Abb. 1.
LEAKAGE CURRENT HOT CHECK
1.  Plug the a.c. cord directly into the a.c. outlet. Do not
use an isolation transformer for this check.
2.
Connect a 2k
 10W resistor in series with an
exposed metallic part on the receiver and an earth,
such as a water pipe.
3.
Use an a.c. voltmeter with high impedance to
measure the potential across the resistor.
4.
Check each exposed metallic part and check the
voltage at each point.
5.
Reverse the a.c. plug at the outlet and repeat each of
the above measurements.
6.
The potential at any point should not exceed 1,4V
rms. In case a measurement is outside the limits
specified, there is a possibility of a shock hazard, and
the receiver should be repaired and rechecked before
it is returned to the customer.
X-RADIATION WARNING
1.  The potential sources of X-Radiation in TV sets are
the high voltage section and the picture tube.
2.
When using a picture tube test jig for service, ensure
that the jig is capable of handling 32kV without
causing X-Radiation.
NOTE : It is important to use an accurate
periodically calibrated high voltage meter.
1.  Set the brightness to minimum.
2.
Measure the high voltage. The meter should indicate
31kV ± 1kV. If the meter indication is out of tolerance,
immediate service and correction is required to
prevent the possibility of premature component
failure.
3.
To prevent any X-Radiation possibility, it is essential
to use the specified tube.
MESSUNG DES KRIECHSTROMS IM
EINGESCHALTETEN ZUSTAND
1.  Den Netzstecker direkt in eine Netsteckdose stecken.
Für diese Messung keinen Trenntransformator
verwenden.
2.
Einen 2k
 / 10W-Widerstand in Serie mit einem von
außen zugänglichen Metallteil am Fernsehgerät und
einer guten, Erdung z.B Wasserleitung, anschließen.
3.
Ein Wechselstrom-Voltmeter mit einem Meßbereich
von 1000 Ohm.Volt oder größer verwenden, um die
Spannung über den Widerstand zu messen.
4.
Jedes zugängliche Metallteil prüfen, und an jedem
Punkt dies Spannung messen.
5.
Den Netztecker umgekehrt in die Steckdose stecken
und jede der obigen Messungen wiederholen.
6.
Die Spannung darf an keinem der Punkte 1,4V eff.
überschreiten. Wird dieser Wert nicht eingehalten,
besteht die Gefar eines elektrischen Schlages, und
das Fernsehgerät sollte daher repariert und
nachgeprüft werden, bevor es an den Kunden
zurückgegeben wird.
RÖNTGENSTRAHLUNG ACHTUNG :
1.  Potentielle Quellen von Röntgenstrahlung in
Fernsehgeräten sind das Hochspannungsteil und die
Bildröhre.
2.
Bei Verwendung eines Bildröhren-Prüfgerätes für den
Service ist sicherzustellen, daß es für die Belastung
von 32kV geeignet ist, ohne daß eine
Röntgenstrahlung verursacht wird.
ANMERKUNG : Es ist wichtig, daß ein präzises,
regelmäßig geprüftes Voltmeter verwendet wird.
1.  Helligkeit auf Minimum stellen.
2.
Die Hochspannung messen. Die Anzeige des
Instrumentes sollte 31kV ± 1kV. Falls die Anziege
diese Toleranzgrenzen überschreitet, ist die sofortige
Behebung nötig, um die Möglichkeit vorzeitigen
Komponentenausfalls zu verhüten.
3.
Um die Möglichkeit von Röntgenstrahlung zu
begrenzen, ist es wichtig, daß nur die
vorgeschriebene Bildröhre verwendet wird.
3
SERVICE HINTS
HOW TO REMOVE THE REAR COVER
1.  Remove the 10 screws as shown in 
Fig. 2.
SERVICE HINWEISE
ENTFERNEN DER GERÄTERÜCKWAND
1.  Die 10 Schrauben entfernen, siehe 
Abb. 2.
LOCATION OF CONTROLS
LAGE DER EINSTELLREGLER
4
SCREWS
SCHRAUBEN
Fig. 2.
Abb. 2.
Y-Board
E-Board
D-Board
H-Board
F-Board
SCREWS
SCHRAUBEN
Fig. 3.
Abb. 3.
Fig. 4.
Abb. 4.
M-Board
Screen
Schirmgitteregler
Focus
Fokusregler
SELF CHECK
1.  Self-check is used to automatically check the bus
lines and hexadecimal code of the TV set.
2.
To get into the Self-Check  mode press the down
(-/v) button on the customer controls at the front of
the set,at the same time pressing the STATUS
button on the remote control, and the screen will
show :-
SELBSTDIAGNOSE
1.  Die Selbstdiagnose dient zum automatischen Prüfen
der Bus-Leitungen sowie des Hexadezimalcodes des
FS-Geräts. Zum Umschalten auf Selbstdiagnose
zunächst die Taste "STATUS" auf der
Fernbedienung und gleichzeitig die-Taste am
Bedienteil des FS-Gerätes drücken (-/v), auf dem
Bildschirm erscheint hierauf :-
2.
Nach der Selbstdiagnose wird das Gerät automatisch
auf sämtliche werksseitigen Standardeinstellungen
zurückgesetzt :-
Service-Hilfen
Zur Unterstützung der Servicearbeiten stehen weitere
Hilfsmittel zur Verfügung.
 
LUCI
 interface kit (PC-unterstützes Diagnosesystem)
Bestell-Nr.: TZS6EZ002
Es beinhaltet ein Interface, die Anschlusskabel zum FS-
Gerät und die Diagnose-Software. Bei Einführung von
neuen Modellen ist ein Update der Software jederzeit
möglich.
 
VICI
 (Interaktive CD-ROM) mit schnellem Zugiff auf
Serviceinformationen.
Bestell-Nr.:TZS7EZ006, TZS7EZ005 & TZS8EZ001
1. Service Manuals
2. Bedienungsanleitungen
3. Technical Information
 
TASMIN
 (Technisch erweitertes System für interaktive
Multimedia-Hinweise und Notizen)
Genauso wie dieses Produkt einen ersten Schritt in
Richtung erweitertes interaktives Training bereitstellt,
ermöglicht es einen noch schnelleren Zugang zu
technischen Informationen.
HINWEIS:
 Dieses FS-Gerät bietet auch die Möglichkeit eines
Memory Pack, mit dem Sie die gewählten Fernsehkanäle
abspeichern und auf jedes beliebige EURO-5L FS-Gerät
umkopieren können.
5
Service Aids
To aid in the service of our current chassis there are a number
of Service Aids which have been made available.
 
LUCI
 interface kit (Linked Utility Computer Interface)
Part number: TZS6EZ002
This contains interface and cables for connecting TV
service connector and a PC as well as diagnostic software.
As new models are introduced upgrade software will
become available.
 
VICI
 (Visual Interactive Computer Information)
These C.D.'s contain multimedia documentation providing
quick access to service information.
Part No. TZS7EZ006, TZS7EZ005 & TZS8EZ001
1. Service Manuals
2. Instruction Books
3. Technical Information
 
TASMIN
 (Technically Advanced System for Multimedia
Interactive Notes)
As well as providing a first step towards more interactive
training this product also achieves quick access to
Technical Information.
NOTE:
 This TV also has the option of using a Memory Pack
which enables you to copy the preset TV channels into the
Memory Pack and then download them onto this or any other
EURO-5L TV set.
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
Wenn der Hauptprozesser (CCU) an den Anschlüssen einen Fehler erkennt, oder der entsprechende Anschluss nicht belegt
ist, zeigt die entsprechende Position " - - " anstelle von OK an.
VPC
O.K.
TUN
O.K.
E2
O.K.
MSP
O.K.
DPL
- -
CI1
O.K.
CI2
O.K.
VP
O.K.
DFU
O.K.
COL
- -
PIP
- -
DIS
O.K.
OPTION 1
B9
OPTION 2
7D
OPTION 3
1F
OPTION 4
80
OPTION 5
FB
OPTION 6
23
PCB
O.K.
Cab
O.K.
Sum
Factory use only
Nur für
Herstellung
ADJUSTMENT PROCEDURE
Item/Preparation
Adjustments
+B SET-UP
1. Receive a Greyscale signal.
2.  Set the controls:-
Brightness:
Minimum
Contrast:
Minimum
Volume:
Minimum
1.
Confirm the following voltages.
D-Board
E-Board
D3,
pin5
147V ±
3V
U8A
E19,
pin8
8V
±
0,5V
D12, pin5
5V
±
0,3V
U9
IC3801, pin3
9V
±
0,5V
D13, pin1
40V
±
4V
U12
E22,
pin8
12V
±
0,5V
D3,
pin4
230V ±
10V
STD5V E26,
pin4
5V
±
0,5V
D14, pin5
5V
±
0,5V
U15
E23,
pin8
15V
±
1V
D12, pin7
15V
±
2V
U15
E23,
pin9
-15V
±
2V
D12, pin9
-15V
±
2V
U33
E22,
pin10 33V
±
4V
D11, pin8
12V
±
2V
U40
E24,
pin1
40V
±
3V
D11, pin10 33V
±
3V
U5B
E19,
pin5
5V
±
0,5V
Cut-Off
1. Receive 
Greyscale 
signal.
2.
Degauss the tube externally.
3.
Set the TV into Service Mode 1.
4.
Select Cutoff mode.
Adjust the screen VR until the display shows "O.K."
ABGLEICH
Vorbereitungen
Abgleich
+B - Abgleich
1. Testbild empfangen.
Helligkeit auf:
Minimum
Kontrast auf:
Minimum
Lautstärke:
Minimum
1.
Folgende Spannungen sind zu überprüfen.
D-Board
E-Board
D3,
pin5
147V ±
3V
U8A
E19,
pin8
8V
±
0,5V
D12, pin5
5V
±
0,3V
U9
IC3801, pin3
9V
±
0,5V
D13, pin1
40V
±
4V
U12
E22,
pin8
12V
±
0,5V
D3,
pin4
230V ±
10V
STD5V E26,
pin4
5V
±
0,5V
D14, pin5
5V
±
0,5V
U15
E23,
pin8
15V
±
1V
D12, pin7
15V
±
2V
U15
E23,
pin9
-15V
±
2V
D12, pin9
-15V
±
2V
U33
E22,
pin10 33V
±
4V
D11, pin8
12V
±
2V
U40
E24,
pin1
40V
±
3V
D11, pin10 33V
±
3V
U5B
E19,
pin5
5V
±
0,5V
Cut-Off
1. Testbild 
empfangen.
2.
Bildröhre entmagnetisieren.
3.
Service-Mode 1 anwählen.
4.
Im Service-Mode den Abgleichpunkt
Cutoff-Mode wählen .
Bis OK auf dem Bildschirm erscheint. Den Wert abspeichern.
6
Page of 43
Display

Panasonic TX-32DK10F Service Manual ▷ Download

  • DOWNLOAD Panasonic TX-32DK10F Service Manual ↓ Size: 13.25 MB | Pages: 43 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Panasonic TX-32DK10F in PDF for free, which will help you to disassemble, recover, fix and repair Panasonic TX-32DK10F TV. Information contained in Panasonic TX-32DK10F Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.