Panasonic TX-28SL20C Service Manual ▷ View online
ADJUSTMENT PROCEDURE
Item/Preparation
Adjustments
+B SET-UP
1. Receive
a
Greyscale
signal.
2. Set the controls:-
Brightness:
Minimum
Contrast:
Minimum
Volume:
Minimum
1. Set the +B voltage up as follows:-
Adjust R811 so that B2 shows 148V±1V
2. Confirm the following voltages.
B9
5
±
0,25V
B10
5
±
0,25V
B5
12
±
0,5V
B11
33
±
1,5V
B4
16
±
1V
B7
8
±
0,5V
B12
26
±
2V
B8
6
±
0,5V
B3
36
±
1,5V
B13
13
±
1V
B1
205 ±
10V
B14
14
±
1V
Cut-Off / Ug2 Test
1. Receive
a
Greyscale
signal.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Cutoff mode.
3. Set the TV into Service Mode 1.
4. Select Cutoff mode.
To adjust Cutoff connect an oscilloscope to the Blue
cathode. Press "STR" and adjust "cutoff" value using the
"Yellow" and "Blue" buttons until the black level is
160V ± 5V, press "STR" to store the value. Remove the
oscilloscope.
Select Ug2 adjustment and adjust the screen VR until the
display shows "O.K."
cathode. Press "STR" and adjust "cutoff" value using the
"Yellow" and "Blue" buttons until the black level is
160V ± 5V, press "STR" to store the value. Remove the
oscilloscope.
Select Ug2 adjustment and adjust the screen VR until the
display shows "O.K."
ABGLEICH
Vorbereitungen
Abgleich
+B - Abgleich
1. Testbild
empfangen.
Helligkeit auf:
Minimum
Kontrast auf:
Minimum
Lautstärke:
Minimum
1. Mit
R811 muß die B2 auf 148V±1V eingestellt
werden.
2. Folgende Spannungen sind zu überprüfen.
B9
5
±
0,25V
B10
5
±
0,25V
B5
12
±
0,5V
B11
33
±
1,5V
B4
16
±
1V
B7
8
±
0,5V
B12
26
±
2V
B8
6
±
0,5V
B3
36
±
1,5V
B13
13
±
1V
B1
205
±
10V
B14
14
±
1V
Cut-Off / Ug2 Test
1. Testbild
empfangen.
2. Bildröhre
entmagnetisieren.
3. Service-Mode 1 anwählen.
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
wählen.
Einen Oszillographen an die blaue Katode der Bildröhre
anschliessen. STR-Taste drücken und Mit der gelben
und blauen Taste den CUT-OFF Wert auf 160V ± 5V
abgleichen und mit der STR-Taste abspeichern. Den
Oszillograph entfernen und den Ug2 Test aufrufen. Den
Abgleichwert solange ändern, bis OK auf dem Bildschirm
erscheint. Den Wert abspeichern.
anschliessen. STR-Taste drücken und Mit der gelben
und blauen Taste den CUT-OFF Wert auf 160V ± 5V
abgleichen und mit der STR-Taste abspeichern. Den
Oszillograph entfernen und den Ug2 Test aufrufen. Den
Abgleichwert solange ändern, bis OK auf dem Bildschirm
erscheint. Den Wert abspeichern.
6
WAVEFORM PATTERN TABLE
SIGNAL TABELLE
7
Video Out
IC601 Pin 59
IC601 Pin 59
2V
64µs
B - Out
E8 Pin 4
E8 Pin 4
64µs
4.6V
64µs
2V
H - Pulse
Base Q503
Base Q503
VFLB
IC451 Pin 3
IC451 Pin 3
1V
20ms
B - Out
IC601 Pin 39
IC601 Pin 39
275
mV
64µs
64µs
3V
H - Out
IC601 Pin 50
IC601 Pin 50
Vert Out
IC601 Pin 31
IC601 Pin 31
20ms
0.7V
13µs
3.7V
SCL
IC1201 Pin 3
IC1201 Pin 3
R - Out
E8 Pin 5
E8 Pin 5
64µs
4.6V
HFLB
IC601 Pin 13
IC601 Pin 13
64µs
6.2V
R - Out
IC601 Pin 37
IC601 Pin 37
64µs
275
mV
G - Out
IC601 Pin 38
IC601 Pin 38
275
mV
64µs
Vert Drive
IC451 Pin 2
IC451 Pin 2
20ms
57V
HFLB
IC701 Pin 8
IC701 Pin 8
64µs
1.5V
G - Out
E8 Pin 3
E8 Pin 3
64µs
4.4V
SVM Out
IC601 Pin 34
IC601 Pin 34
88mV
64µs
H - Out
IC701 Pin 5
IC701 Pin 5
30mV
64µs
ALIGNMENT SETTINGS
:
(The figures below are nominal and used for representative purposes only.)
1. Set the Bass to maximum position, set the Treble to minimum position, press the volume down button
1. Set the Bass to maximum position, set the Treble to minimum position, press the volume down button
(-/v) on the customer controls at the front of the TV and at the same time press the INDEX button on the remote
control, this will place the TV into the Service Mode.
control, this will place the TV into the Service Mode.
2. Press
the
RED / GREEN buttons to step up / down through the functions.
3. Press
the
YELLOW / BLUE buttons to alter the function values.
4. Press
the
STR button after each adjustment has been made to store the required values.
5. To exit the Service Mode, press the "N" button.
Alignment Function
Settings / Special features
Horizontal Position
H-Pos
061
Optimum setting.
Vertical Position
V-Pos
005
Optimum setting.
Horizontal Amplitude
H-Amp
055
Optimum setting.
Vert. Amplitude
V. Amp
054
Optimum setting.
EW-amplitude
E/W-Amp1
-128
Optimum setting.
EW-amplitude
E/W-Amp2
006
Optimum setting.
Trapezium-comp
Trapez-1
047
Optimum setting.
Trapezium-comp
Trapez-2
-128
Optimum setting.
Vertical Linearity
V-Lin
006
Optimum setting.
Vertical Symmetry
V-Sym
002
Optimum setting.
DVCO
DVCO
-005
Receive a PAL Colour Bar Pattern. For
DVCO alignment press "Blue" button, wait
until the colours are changing slowly and
press "STR".
DVCO alignment press "Blue" button, wait
until the colours are changing slowly and
press "STR".
Cut-off DC
Cut-off
0171
Ug2 Test
Ug2
055
O.K.
To adjust Cutoff connect an oscilloscope to
the Blue cathode. Press "STR" and adjust
"cutoff" value using the "Yellow" and
"Blue" buttons until the black level is
160V ± 5V press "STR" to store the value.
Remove the oscilloscope.
Select Ug2 adjustment and adjust the
screen VR until the display shows "O.K."
the Blue cathode. Press "STR" and adjust
"cutoff" value using the "Yellow" and
"Blue" buttons until the black level is
160V ± 5V press "STR" to store the value.
Remove the oscilloscope.
Select Ug2 adjustment and adjust the
screen VR until the display shows "O.K."
Highlight
Lowlight
High
0902 0777 0864
Low
0117 0132 0112
Optimum setting.
Sub-Brightness
Sub-Brightness
255
Optimum setting.
Black Level
160V±5V
GND
8
ABGLEICHTABELLE
(Die angegebenen Werte sind Mittelwerte und Können individuell nach oben oder unten nach dem korrekten Abgleich
abweichen.)
1. Um in den Service-Mode zu gelangen, gehen sie bitte wie folgt vor.
2. Stellen sie im Toneinstellungs-Menü die Bässe auf Maximun und die Höhen auf Minimum.
3. Halten
abweichen.)
1. Um in den Service-Mode zu gelangen, gehen sie bitte wie folgt vor.
2. Stellen sie im Toneinstellungs-Menü die Bässe auf Maximun und die Höhen auf Minimum.
3. Halten
sie
die
INDEX-Taste auf der Fernbedienung gedrückt und drücken zusätzlich die Taste -/v im Bedienteil des TV-
Gerätes. Auf dem Bildschirm erscheint die entsprechende Anzeige für den Service-Mode.
4. Die einzelnen Funktionen mit Hilfe der ROTEN und GRÜNEN Taste anwählen.
5. Mit der GELBEN und BLAUEN Taste die Werte der einzelnen Funktionen ändern.
6. Nach jeder Einstellung die Taste STR auf der Fernbedienung drücken, um die geänderten Werte abzuspeichern.
7. Zum Verlassen des Service-Modus die "N" - Taste auf der Fernbedienung drücken.
5. Mit der GELBEN und BLAUEN Taste die Werte der einzelnen Funktionen ändern.
6. Nach jeder Einstellung die Taste STR auf der Fernbedienung drücken, um die geänderten Werte abzuspeichern.
7. Zum Verlassen des Service-Modus die "N" - Taste auf der Fernbedienung drücken.
Abgleichfunktion
Einstellung / Besondere Merkmale
Horizontale position
H-Pos
061
Optimale Einstellung.
Vertikale Position
V-Pos
005
Optimale Einstellung.
Horizontale Amplitude
H-Amp
055
Optimale Einstellung.
Vertikale Amplitude
V-Amp
054
Optimale Einstellung.
OW-amplitude
E/W-Amp1
-128
Optimale Einstellung.
OW-amplitude
E/W-Amp2
006
Optimale Einstellung.
Trapez-Kompensation
Trapez-1
047
Optimale Einstellung.
Trapez-Kompensation
Trapez-2
-128
Optimale Einstellung.
Vertikale linearität
V-Lin
006
Optimale Einstellung.
Vertikale Symmetrie
V-Sym
002
Optimale Einstellung.
DVCO
DVCO
-005
Ein Farbbalken-Testbild empfangen. Zum
Abgleich des Farboszillators (DVCO) die
blau Taste drücken. Nachdem ein leichtes
Flackern in den Farbbalken zum Stillstand
gekommen ist, die STR-Taste drücken.
Abgleich des Farboszillators (DVCO) die
blau Taste drücken. Nachdem ein leichtes
Flackern in den Farbbalken zum Stillstand
gekommen ist, die STR-Taste drücken.
Cut-off
Cut-off
0171
Ug2 Test
Ug2
055
O.K.
Einen Oszillographen an die blaue Katode
der Bildröhre anschliessen. STR-Taste
drücken und Mit der gelben und blauen
Taste den CUT-OFF Wert auf 160V ± 5V
abgleichen und mit der STR-Taste
abspeichern. Den Oszillograph entfernen
und den Ug2 Test aufrufen. Den
Abgleichwert solange ändern, bis OK auf
dem Bildschirm erscheint. Den Wert
abspeichern.
der Bildröhre anschliessen. STR-Taste
drücken und Mit der gelben und blauen
Taste den CUT-OFF Wert auf 160V ± 5V
abgleichen und mit der STR-Taste
abspeichern. Den Oszillograph entfernen
und den Ug2 Test aufrufen. Den
Abgleichwert solange ändern, bis OK auf
dem Bildschirm erscheint. Den Wert
abspeichern.
Highlight
Lowlight
High
0902 0777 0864
Low
0117 0132 0112
Optimale Einstellung.
Sub-Brightness
Sub-Brightness
255
Optimale Einstellung.
Black Level
160V±5V
GND
9
Click on the first or last page to see other TX-28SL20C service manuals if exist.