Panasonic TX-28PL10D / TX-28PL10F Service Manual ▷ View online
HOW TO MOVE THE CHASSIS
INTO SERVICE POSITION
INTO SERVICE POSITION
1. Remove
2
screws
(A), as shown in
Fig.4.
, and
remove speaker assembly.
2. Hold and lift the rear of the chassis and gently pull
the chassis toward you, as shown in
Fig.4.
3. Release the respective wiring clips.
4. Elevate the chassis as shown in
4. Elevate the chassis as shown in
Fig .5.
5. Using a speaker screw, screw the chassis frame into
the top speaker fixing rib (B), as shown in
Fig.6.
6. After servicing replace the speaker, and ensure all
wiring is returned to its original position before
returning the receiver to the customer.
returning the receiver to the customer.
SERVICE POSITION
FÜR DAS CHASSIS
FÜR DAS CHASSIS
1. Die 2 Schrauben (A) entfernen, wie in
Abb.4.
dargestellt, und
die Lautsprechereinheit herausnehmen.
2. Das Chassis leicht anheben und nach hinten herausziehen,
wie in
Abb. 4.
dargestellt.
3. Entsprechende
Kabelklemmen
losmachen.
4. Das Chassis, wie in
Abb. 5.
gezeigt, herausheben.
5. Mit einer Lautsprecherschraube den Chassisrahmen durch das
Langloch auf der rechten Seite des Rahmens im oberen
Befestigungsloch des Latsprechers fixieren. Siehe
Befestigungsloch des Latsprechers fixieren. Siehe
Abb.6.
6. Nach Beendigung der Reparatur ist sicherzustellen, daß sich
alle Kabel in ihrer ursprünglichen Position befinden.
5
(B)
(A)
(A)
Fig.4
Abb.4
Fig.5
Abb.5
(B)
Fig.6.
Abb.6.
SELF CHECK
1. Self-check is used to automatically check the bus
lines and hexadecimal code of the TV set.
2. To get into the Self-Check mode press the STATUS
button on the remote control and at the same time
press the down (-/v) button on the customer controls
at the front of the set, and the screen will show :
press the down (-/v) button on the customer controls
at the front of the set, and the screen will show :
SELBSTDIAGNOSE
1. Die Selbstdiagnose dient zum automatischen Prüfen
der Bus-Leitungen sowie des Hexadezimalcodes des
FS-Geräts. Zum Umschalten auf Selbstdiagnose
zunächst die Taste "STATUS" auf der
Fernbedienung und gleichzeitig die-Taste am
Bedienteil des FS-Gerätes drücken (-/v), auf dem
Bildschirm erscheint hierauf :
FS-Geräts. Zum Umschalten auf Selbstdiagnose
zunächst die Taste "STATUS" auf der
Fernbedienung und gleichzeitig die-Taste am
Bedienteil des FS-Gerätes drücken (-/v), auf dem
Bildschirm erscheint hierauf :
2. Nach der Selbstdiagnose wird das Gerät automatisch
auf sämtliche werksseitigen Standardeinstellungen
zurückgesetzt :
zurückgesetzt :
Service-Hilfen
Zur Unterstützung der Servicearbeiten stehen weitere
Hilfsmittel zur Verfügung.
•
Hilfsmittel zur Verfügung.
•
LUCI
interface kit (PC-unterstützes Diagnosesystem)
Bestell-Nr.: TZS6EZ002
Es beinhaltet ein Interface, die Anschlusskabel zum FS-
Gerät und die Diagnose-Software. Bei Einführung von
neuen Modellen ist ein Update der Software jederzeit
möglich.
Es beinhaltet ein Interface, die Anschlusskabel zum FS-
Gerät und die Diagnose-Software. Bei Einführung von
neuen Modellen ist ein Update der Software jederzeit
möglich.
•
VICI
(Interaktive CD-ROM) mit schnellem Zugiff auf
Serviceinformationen.
Bestell-Nr.:
TZS7EZ006, TZS7EZ005, TZS8EZ001 & TZS9EZ001
1. Service Manuals
2. Bedienungsanleitungen
3. Technical Information
Bestell-Nr.:
TZS7EZ006, TZS7EZ005, TZS8EZ001 & TZS9EZ001
1. Service Manuals
2. Bedienungsanleitungen
3. Technical Information
•
TASMIN
(Technisch erweitertes System für interaktive
Multimedia-Hinweise und Notizen)
Genauso wie dieses Produkt einen ersten Schritt in
Richtung erweitertes interaktives Training bereitstellt,
ermöglicht es einen noch schnelleren Zugang zu
technischen Informationen.
Genauso wie dieses Produkt einen ersten Schritt in
Richtung erweitertes interaktives Training bereitstellt,
ermöglicht es einen noch schnelleren Zugang zu
technischen Informationen.
• Verlängerungskabelvorrichtung zur Verbindung Y2-E8
(Abb.6.); Bestell-Nr.: TZS9EK012.
Service Aids
To aid in the service of our current chassis there are a number
of Service Aids which have been made available.
•
of Service Aids which have been made available.
•
LUCI
interface kit (Linked Utility Computer Interface)
Part number: TZS6EZ002
This contains interface and cables for connecting TV
service connector and a PC as well as diagnostic software.
As new models are introduced upgrade software will
become available.
This contains interface and cables for connecting TV
service connector and a PC as well as diagnostic software.
As new models are introduced upgrade software will
become available.
•
VICI
(Visual Interactive Computer Information)
These C.D.'s contain multimedia documentation providing
quick access to service information.
Part No.
TZS7EZ006, TZS7EZ005, TZS8EZ001 & TZS9EZ001
1. Service Manuals
2. Instruction Books
3. Technical Information
quick access to service information.
Part No.
TZS7EZ006, TZS7EZ005, TZS8EZ001 & TZS9EZ001
1. Service Manuals
2. Instruction Books
3. Technical Information
•
TASMIN
(Technically Advanced System for Multimedia
Interactive Notes)
As well as providing a first step towards more interactive
training this product also achieves quick access to
Technical Information.
As well as providing a first step towards more interactive
training this product also achieves quick access to
Technical Information.
• Extended cable kit Y2-E8 connector for service position
(Fig.6.). Part No.: TZS9EK012.
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
Wenn der Hauptprozesser (CCU) an den Anschlüssen einen Fehler erkennt, oder der entsprechende Anschluss nicht belegt
ist, zeigt die entsprechende Position " - - " anstelle von OK an.
Wenn der Hauptprozesser (CCU) an den Anschlüssen einen Fehler erkennt, oder der entsprechende Anschluss nicht belegt
ist, zeigt die entsprechende Position " - - " anstelle von OK an.
VPC
O.K.
CIP
O.K.
SRC
O.K.
DDP
O.K.
TUN
O.K.
E2
O.K.
MSP
O.K.
DPL
- - -
PCB
O.K.
CAB
O.K.
6
TX-28PL10F:
OPTION1
39
OPTION2
7F
OPTION3
0F
OPTION4
40
OPTION5
FD
OPTION6
A5
TX-28PL10D:
OPTION1
39
OPTION2
7F
OPTION3
0F
OPTION4
40
OPTION5
FF
OPTION6
A5
ADJUSTMENT PROCEDURE
Item/Preparation
Adjustments
+B SET-UP
1. Receive a Greyscale signal.
2. Set
2. Set
the
controls:-
Brightness:
Minimum
Contrast:
Minimum
Volume:
Minimum
1. Confirm the following voltages.
B2
148 ± 2V
B9
5
± 0,25V
B10
5
± 0,25V
B5
12
± 0,5V
B11
33
± 1,5V
B4
15
± 1V
B7
8
± 0,5V
B12
26
± 2V
B8
7
± 1V
B3
36
± 1,5V
B13
16
± 1V
B1
205 ± 10V
B14
-14 ± 1V
Cut-Off / Ug2 Test
1. Receive a Greyscale signal.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Cutoff mode.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Cutoff mode.
Connect an oscilloscope to the Blue cathode, adjust
"Screen" until the black level is 155V±3V. Remove the
oscilloscope.
"Screen" until the black level is 155V±3V. Remove the
oscilloscope.
ABGLEICH
Vorbereitungen
Abgleich
+B - Abgleich
1. Testbild
empfangen.
Helligkeit auf:
Minimum
Kontrast auf:
Minimum
Lautstärke:
Minimum
1. Folgende Spannungen sind zu überprüfen.
B2
148 ± 2V
B9
5
± 0,25V
B10
5
± 0,25V
B5
12
± 0,5V
B11
33
± 1,5V
B4
15
± 1V
B7
8
± 0,5V
B12
26
± 2V
B8
7
± 1V
B3
36
± 1,5V
B13
16
± 1V
B1
205 ± 10V
B14
-14 ± 1V
Cut-Off / Ug2 Test
1. Testbild
empfangen.
2. Bildröhre
entmagnetisieren.
3. Service-Mode 1 anwählen.
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
wählen.
Das Oszilloskop an blaue Kathode anschließen, den
Wert „SCREEN“ so einstellen, dass das schwarze
Niveau 155
Wert „SCREEN“ so einstellen, dass das schwarze
Niveau 155
± 3V beträgt. Das Oszilloskop abschalten.
7
WAVEFORM PATTERN TABLE SIGNAL TABELLE
8
CONDITIONS:
CONTRAST...MAX, BRIGHTNESS...MID, COLOUR...MID, SHARPNESS...MID
Click on the first or last page to see other TX-28PL10D / TX-28PL10F service manuals if exist.