Panasonic TX-21PS70TQ Service Manual ▷ View online
2.2 Factory Mode Adjustment
TOP
PREVIOUS
NEXT
●
How to set :
To set the Factory mode, press Volume 0 dac on the TV and Timer Setting 30 min. on the remote
control and press Volume (-) Down button on the TV together press recall on the remote control.
CHK should appear on right of TV screen.
To movefrom CHK1 to CHK2 mode, etc. please follow below rotation :
control and press Volume (-) Down button on the TV together press recall on the remote control.
CHK should appear on right of TV screen.
To movefrom CHK1 to CHK2 mode, etc. please follow below rotation :
●
●
To Set Self-Check :
Press the Volume Down button on TV then press the Off Timer button on remote control.
●
TOP
PREVIOUS
NEXT
2.3 Adjustment for White Balance
TOP
PREVIOUS
NEXT
Preparation:
1. Receive the white balance pattern and aging should have been performed over 30 minutes.
2. Set the picture menu to DYNAMIC NORMAL.
3. Degausse the CRT face.
4. Fix the CRT colour analyzer receiver unit to CRT face.
Adjustment of Low Light.
1. Adjustment Sub Bright, so that Y = 6.3 ± 1.0 nit.
2. Adjustment R-CUT OFF, so that X = 0.235 ± 0.010 nit.
3. Adjustment G-CUT OFF, so that Y = 0.235 ± 0.010 nit.
Adjustment of High Light
1. Adjustment Sub Bright, so that Y = 270 nit.
2. Adjustment R-Drive, so that X = 0.265 ± 0.010 nit.
3. Adjustment B-Drive, so that Y = 0.265 ± 0.010 nit.
TOP
PREVIOUS
NEXT
2.4 Adjustment for CRT CUT OFF
TOP
PREVIOUS
NEXT
Preparation:
1. Connect the oscilloscope probe to TPL5.
2. Screen VR min.
3. Set the data Sub Bright, Bright.
4. In service Mode at “Bright” dac press [5] in factory mode to enter vertical line and adjust by
volume down or up button.
5. Adjust “Screen VR” until 1-H Line appears.
TOP
PREVIOUS
NEXT
2.5 Adjustment Procedure
TOP
PREVIOUS
NEXT
Item / Preparation
Adjustment Procedure
+B Voltage
Confirm the DC voltage at the indicated test points, as follows :
1. Operate the TV set.
TPA 9 : 5 ± 1V
2. Set control as follows :
TPA 8 : 8 ± 1V
Brightness ...........
minimum
minimum
TPA 10 : 141.0 ± 1.5V
Contrast ..............
minimum
minimum
TPA 21 : 175 ± 15V
RF AGC
1. Receive a colour bar
signal at an RF level of
69 +1-2 dBU with 75
69 +1-2 dBU with 75
Ω
loaded.
1. Select “RF AGC” indication in CHK2, on Screen by remote control at factory mode.
2. Connect digital
multimeter to RF AGC at
Tuner.
Tuner.
2. Set RF AGC by using remote control Volume (+) or Volume (-) button until voltage AGC at Tuner
reaches 2.3 ± 0.1V at TPA 15 (Tuner point).
3. Increase RF signal strength by 2dB, confirm AGC at Tuner voltage drop.
High Voltage
1. Receive the crosshatch
pattern.
1. Connect a DC voltage meter to TPA 12 and confirm the +B voltage is 140.5 ± 1.5V.
2. Set to 0 Beam.
Screen VR ..........
minimum
minimum
2. Connect a high frequency voltmeter to heater and confirm that voltage reads 6.3 ± 0.24 (VRMS).
Contrast ..............
minimum
minimum
3. Normalize the brightness and contrast.
Item / Preparation
Adjustment Procedure
NTSC TINT COLOUR
Connect oscilloscope probe
to TPL1 ( R out ).
Press Main Menu and set
to TPL1 ( R out ).
Press Main Menu and set
1. Adjust Sub-Tint so that No. 2, 3 and 4 becomes level waveform is similar to Fig. 3.
Click on the first or last page to see other TX-21PS70TQ service manuals if exist.