DOWNLOAD Panasonic TX-21FX50T Service Manual ↓ Size: 2.02 MB | Pages: 29 in PDF or view online for FREE

Model
TX-21FX50T
Pages
29
Size
2.02 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / GP41 CHASSIS
File
tx-21fx50t.pdf
Date

Panasonic TX-21FX50T Service Manual ▷ View online

2.3. Adjustment for White Balance
Preparation:
 1. Receive the white balance pattern and aging should have been performed over 30 minutes.
 2. Set the picture menu to DYNAMIC NORMAL.
 3. Degausse the CRT face.
 4. Fix the CRT colour analyzer receiver unit to CRT face.
Adjustment of Low Light.
 1. Adjustment Sub Bright, so that Y = 6.5 ± 1.0 nit.
 2. Adjustment R-CUT OFF, so that X = 0.313 ± 0.015 nit.
 3. Adjustment G-CUT OFF, so that Y = 0.320 ± 0.015 nit.
Adjustment of High Light
 1. Adjustment Sub Bright, so that Y = 150 nit.
 2. Adjustment R-Drive, so that X = 0.275 ± 0.015 nit.
 3. Adjustment B-Drive, so that Y = 0.285 ± 0.015 nit.
2.4. Adjustment for CRT CUT OFF
Preparation:
 1. Connect the oscilloscope probe to TPL5.
 2. Screen VR min.
 3. Set the data Sub Bright, Bright.
 4. In service Mode at “Bright” dac press [5] in factory mode to enter vertical line and adjust by volume down or up button.
 5. Adjust “Screen VR” until 1-H Line appears.
7
TX-21FX50T
2.5. Adjustment Procedure
2.5.1. +B Voltage
Item / preparation
 1. Operate the TV set.
 2. Set control as follows :
Brightness ........... minimum
Contrast ............... minimum
Adjustment procedure
 1. Confirm the DC voltage at the indicated test points, as follows :
TPA 15 : 3.35 ± 0.2V
TPA 16 : 141 ± 2V
TPA 17 : 8.2 ± 0.5V
TPA 18 : 1.9 ± 0.2V
TPA 19 : 5.2 ± 0.2V
TPA 20 : 175 ± 15V
2.5.2. High Voltage
Item / preparation
 1. Receive the crosshatch pattern.
 2. Set to 0 Beam.
Screen VR .......... minimum
Contrast .............. minimum
Adjustment procedure
 1. Connect a DC voltage meter to TPA 16 and confirm the +B voltage is 141.0 ± 2V.
 2. Connect a high frequency voltmeter to heater and confirm that voltage reads 6.3 ± 0.24 (VRMS).
 3. Normalize the brightness and contrast.
8
TX-21FX50T
Colour Purity
 1. Set the Brightness and Contrast controls to their maximum
positions.
 2. Operate the TV set for 60 minutes.
 3. Fully degausse the picture tube by using an external
degaussing coil.
 4. Apply a crosshatch pattern signal and adjust the static
convergence magnets to the approximately correct position.
 5. Receive a black and white signal.
 6. Set the control as follows:
Red................minimum
Green.............minimum
Blue...............minimum
Press the Shipping button on the remote control twice to
select CRT Adjustment Mode to select low light.
 7. Loosen the clamp screw for the Deflection Yoke A in Fig. 10
and move the Deflection Yoke as close to the purity magnet
as possible.
 8. Adjust the purity magnetic rings so that a vertical green field
is obtained at the centre of the screen.
Fig. 6
 9. Slowly push the Deflection Yoke and set it where a uniform
green field is obtained.
Fig. 21
 10. Re-adjust the Low Light controls to their correct settings
and make sure that a uniform white field is obtained.
 11. Tighten the clamp screw A in Fig. 10.
Convergence
 1. Apply a crosshatch pattern signal and Normalize Contrast
control to the maximum positions.
 2. Adjust Brightness until the grey position of the crosshatch
pattern just becomes black.
 3. Adjust the Red and Blue line at the centre of the screen by
rotating the R-B static.
Fig. 8
 4. Adjust Red and Blue with Green line at centre of the screen
by rotating (RB)-G static convergence magnetic rings.
 5. Lock convergence magnets with silicone sealer.
 6. Remove the DY wedges and slightly tilt the Deflection Yoke
vertically and horizontally to obtain the good overall
convergence.
Fig. 9
 7. Fix the Deflection Yoke by reinserting the DY wedges. Refer
to Fig. 10.
 8. If purity error is found, repeat “Colour Purity” adjustment.
2.6. Adjustment
Before Colour Purity, Convergence and White Balance adjustment are attempted,
V. Height, H. Centre and Focus adjustments must be completed.
9
TX-21FX50T
Adjustment of CRT VRS
 1. Preparation
 a. Set DY to CRT not to tilt up and down left and right deflection.
 b. Set CY to CRT and set CY magnet primarily (Fig. 1)
Purity magnet : Set purity magnet that 2 magnets are (TOP POSITION)
VRS magnet : Set purity magnet 2 magnets are (HORIZONTAL POSITION)
 2. Adjustment
 a. Receive that Cross Hatch pattern.
 b. Adjust V-SHIFT -50Hz.
 c. 
Set 2 magnets of horizontal position to up and down equally so that it will be the center part of CRT. (Fig. 2)
10
TX-21FX50T
Page of 29
Display

Click on the first or last page to see other TX-21FX50T service manuals if exist.