Panasonic TX-21AT1C Service Manual ▷ View online
SERVICE HINTS
HOW TO REMOVE THE REAR COVER
1. Remove the 5 screws as shown in
Fig.2.
SERVICE HINWEISE
ENTFERNEN DER GERÄTERÜCKWAND
1. Die 5 Schrauben entfernen, siehe
Abb.2.
LOCATION OF CONTROLS
LAGE DER EINSTELLREGLER
4
Fig.2.
Abb.2.
Screws
Schrauben
Screws
Schrauben
Focus
Fokusregler
Fig.3.
Abb.3.
E - Board
Y - Board
Screen
Schirmgitterregler
SELF CHECK
1. Self-check is used to automatically check the bus
lines and hexadecimal code of the TV set.
2. To get into the Self-Check mode press the STATUS
button on the remote control and at the same time
press the down (-/v) button on the customer controls
at the front of the set, and the screen will show :
press the down (-/v) button on the customer controls
at the front of the set, and the screen will show :
SELBSTDIAGNOSE
1. Die Selbstdiagnose dient zum automatischen Prüfen
der Bus-Leitungen sowie des Hexadezimalcodes des
FS-Geräts. Zum Umschalten auf Selbstdiagnose
zunächst die Taste "STATUS" auf der
Fernbedienung und gleichzeitig die-Taste am
Bedienteil des FS-Gerätes drücken (-/v), auf dem
Bildschirm erscheint hierauf :-
FS-Geräts. Zum Umschalten auf Selbstdiagnose
zunächst die Taste "STATUS" auf der
Fernbedienung und gleichzeitig die-Taste am
Bedienteil des FS-Gerätes drücken (-/v), auf dem
Bildschirm erscheint hierauf :-
2. Nach der Selbstdiagnose wird das Gerät automatisch
auf sämtliche werksseitigen Standardeinstellungen
zurückgesetzt
zurückgesetzt
Service-Hilfen
Zur Unterstützung der Servicearbeiten stehen weitere
Hilfsmittel zur Verfügung.
·
Hilfsmittel zur Verfügung.
·
LUCI
interface kit (PC-unterstützes Diagnosesystem)
Bestell-Nr.: TZS6EZ002
Es beinhaltet ein Interface, die Anschlusskabel zum FS-
Gerät und die Diagnose-Software. Bei Einführung von
neuen Modellen ist ein Update der Software jederzeit
möglich.
Es beinhaltet ein Interface, die Anschlusskabel zum FS-
Gerät und die Diagnose-Software. Bei Einführung von
neuen Modellen ist ein Update der Software jederzeit
möglich.
·
VICI
(Interaktive CD-ROM) mit schnellem Zugiff auf
Serviceinformationen.
Bestell-Nr.: TZS7EZ006, TZS7EZ005, & TZS8EZ001 &
TZS9EZ001
1. Service Manuals
2. Bedienungsanleitungen
3. Technical Information
Bestell-Nr.: TZS7EZ006, TZS7EZ005, & TZS8EZ001 &
TZS9EZ001
1. Service Manuals
2. Bedienungsanleitungen
3. Technical Information
·
TASMIN
(Technisch erweitertes System für interaktive
Multimedia-Hinweise und Notizen)
Genauso wie dieses Produkt einen ersten Schritt in
Richtung erweitertes interaktives Training bereitstellt,
ermöglicht es einen noch schnelleren Zugang zu
technischen Informationen.
Genauso wie dieses Produkt einen ersten Schritt in
Richtung erweitertes interaktives Training bereitstellt,
ermöglicht es einen noch schnelleren Zugang zu
technischen Informationen.
OPTION 1
60
OPTION 2
02
5
Service Aids
To aid in the service of our current chassis there are a number
of Service Aids which have been made available.
·
of Service Aids which have been made available.
·
LUCI
interface kit (Linked Utility Computer Interface)
Part number: TZS6EZ002
This contains interface and cables for connecting TV
service connector and a PC as well as diagnostic software.
As new models are introduced upgrade software will
become available.
This contains interface and cables for connecting TV
service connector and a PC as well as diagnostic software.
As new models are introduced upgrade software will
become available.
·
VICI
(Visual Interactive Computer Information)
These C.D.'s contain multimedia documentation providing
quick access to service information.
Part No. TZS7EZ006, TZS7EZ005, TZS8EZ001 &
TZS9EZ001
1. Service Manuals
2. Instruction Books
3. Technical Information
quick access to service information.
Part No. TZS7EZ006, TZS7EZ005, TZS8EZ001 &
TZS9EZ001
1. Service Manuals
2. Instruction Books
3. Technical Information
·
TASMIN
(Technically Advanced System for Multimedia
Interactive Notes)
As well as providing a first step towards more interactive
training this product also achieves quick access to
Technical Information.
As well as providing a first step towards more interactive
training this product also achieves quick access to
Technical Information.
ADJUSTMENT PROCEDURE
Item/Preparation
Adjustments
Confirm the following voltages.
+B SET-UP
1. Receive a Greyscale signal.
2. Set the controls:
2. Set the controls:
Brightness Minimum
Contrast
Minimum
Volume
Minimum
B1
3,3 ± 0,3V
B13
-16 ± 1V
B2
190
± 10V
B14
27,5
± 1,5V
B3
16
± 1V
B15
28
± 1,5V
B4
10
± 1V
B16
13 ± 1V
B8
5
± 0,3V
B17
8
± 1V
B11 127
± 10V
B18
5
± 0,3V
Cut-Off / Ug2 Adjustment
1. Receive a Greyscale signal.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Ug2 Test.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Ug2 Test.
Set Contrast on maximum, set Brightness on centre, switch
on AV mode.
Enter Service mode. Set Sub-Brightness to 31. Select
Ug2.Press "+" and adjust screen Vr till sharp vertical line is
visible and LED switches off. Then reduce screen Vr till LED
is just switched on.
on AV mode.
Enter Service mode. Set Sub-Brightness to 31. Select
Ug2.Press "+" and adjust screen Vr till sharp vertical line is
visible and LED switches off. Then reduce screen Vr till LED
is just switched on.
Note: To set up ”white balance” first set up “Cut off” register to 8. Then set up “high-light” with the help of “drive” registers.
Finish setting-up of “Low-light” with the help of ”Cut-off” register. Carry out setting-up of ”white balance” in available TV
systems (PAL, SECAM).
Finish setting-up of “Low-light” with the help of ”Cut-off” register. Carry out setting-up of ”white balance” in available TV
systems (PAL, SECAM).
ABGLEICH
Vorbereitungen
Abgleich
Folgende Spannungen sind zu überprüfen.
+B – Abgleich
1. TV einschalten, pattern cross hatch.
2.
Helligkeit auf
Minimum
Kontrast auf
Minimum
Lautstärke
Minimum
B1
3,3 ± 0,3V
B13
-16 ± 1V
B2
190
± 10V
B14
27,5
± 1,5V
B3
16
± 1V
B15
28
± 1,5V
B4
10
± 1V
B16
13 ± 1V
B8
5
± 0,3V
B17
8
± 1V
B11 127
± 10V
B18
5
± 0,3V
Cut-Off / Ug2 Test
1. Testbild empfangen.
2. Bildröhre entmagnetisieren.
3. Service-Mode 1 anwählen.
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
2. Bildröhre entmagnetisieren.
3. Service-Mode 1 anwählen.
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
wählen.
Stellen Sie den Kontrast auf das Maximum und die Hellgkeit
auf die Mitte ein, schalten Sie in den Mode "AV" um. Treten
Sie in den Service Mode ein. Stellen Sie die Sub-Brightness
auf den Wert 31 ein.
Wählen Sie "Ug2" aus. Drüken Sie "+" und stellen Sie den
Screen "Vr" so, dass die vertikale dünne Linie schrarf
sichtbar ist und L.E.D. sich ausschaltet.
Dann nehmen Sie den Screen "Vr" ab,bis sich L.E.D.
anzündet.
auf die Mitte ein, schalten Sie in den Mode "AV" um. Treten
Sie in den Service Mode ein. Stellen Sie die Sub-Brightness
auf den Wert 31 ein.
Wählen Sie "Ug2" aus. Drüken Sie "+" und stellen Sie den
Screen "Vr" so, dass die vertikale dünne Linie schrarf
sichtbar ist und L.E.D. sich ausschaltet.
Dann nehmen Sie den Screen "Vr" ab,bis sich L.E.D.
anzündet.
Hinweis: Um die ”White Balance“ einzustellen, stellen Sie zuerst das “Cut off“ Register auf 8 ein. Dann stellen Sie mit der
Hilfe von “Drive“ Registern “High-Light“ ein. Beenden Sie die Einstellung von “Low-Light“ mit der Hilfe von dem “Cut off“
Register. Führen Sie die Einstellung von “White Balance“ in den zugänglichen Systemen (PAL, SECAM) durch.
Hilfe von “Drive“ Registern “High-Light“ ein. Beenden Sie die Einstellung von “Low-Light“ mit der Hilfe von dem “Cut off“
Register. Führen Sie die Einstellung von “White Balance“ in den zugänglichen Systemen (PAL, SECAM) durch.
6
WAVEFORM PATTERN TABLE SIGNAL TABELLE
7
CONDITIONS:
Contrast:
MAX
Brightness:
MID
Colour:
MID
Sharpness:
MID