Panasonic TH-80BF1U / TH-80BF1W / TH-80BF1E Service Manual ▷ View online
6
PREFACE
<80BF1>
6
TH-50LFC70U/TH-50LFC70W
2.2. About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
suggest the use of Pb free solder as well, although Pb solder may be used.
Caution
• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher. Please
use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol-
der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the
opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How-
ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
2.2. About lead free solder (PbF)
7
PREFACE
<80BF1>
3. Specifications
106
Specifications
TH-80BF1U
TH-80BF1E / TH-80BF1W
Power Source
110 - 127 V ~ (110 - 127 V alternating current),
50/60Hz
220 - 240 V ~ (220 - 240 V alternating current),
50/60Hz
Power Consumption
Power on
350 W
350 W
Stand-by condition
0.5 W
0.5 W
Power off condition
0.3 W
0.3 W
LCD Display panel
80-inch VA panel (LED backlight), 16:9 aspect ratio
Screen size
1,771 mm (W) × 996 mm (H) × 2,032 mm (diagonal) /
69.7” (W) × 39.2” (H) × 80.0” (diagonal)
(No.of pixels)
2,073,600 (1,920 (W) ×1,080 (H))
[5,760 × 1,080 dots]
Operating condition
Temperature
32 °F - 104 °F (0 °C - 40 °C)
Humidity
20 % - 80 % (no condensation)
Applicable signals
Colour System
NTSC, PAL, PAL60, SECAM, Modified NTSC
Scanning format
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 60p · 50i ·
50p · 24p · 25p · 30p · 24psF, 1250 (1080) / 50i
PC signals
VGA, SVGA, XGA, SXGA
UXGA ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
AV IN
VIDEO
AUDIO 1 IN
BNC
Stereo mini jack (M3) × 1
1.0 Vp-p (75 Ω)
0.5 Vrms, Shared with COMPONENT/RGB IN
HDMI 1
HDMI 2
TYPE A Connector × 2
COMPONENT/RGB IN
Y/G
PB/CB/B
PR/CR/R
AUDIO 1 IN
BNC
BNC
BNC
Stereo mini jack (M3) × 1
with sync 1.0 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
0.5 Vrms, Shared with VIDEO
DVI-D IN
AUDIO 2 IN
DVI-D 24 Pin
Content Protection
Stereo mini jack (M3) × 1
Compliance with DVI Revision 1.0
Compatible with HDCP 1.1
0.5 Vrms, Shared with PC IN
PC IN
AUDIO 2 IN
High-Density Mini D-sub 15 Pin
Stereo mini jack (M3) × 1
Y or G with sync 1.0 Vp-p (75 Ω)
Y or G without sync 0.7 Vp-p (75 Ω)
PB/CB/B: 0.7 Vp-p (75 Ω)
PR/CR/R: 0.7 Vp-p (75 Ω)
TTL high impedance, positive polarity /
negative polarity (automatic)
0.5 Vrms, Shared with DVI-D IN
SERIAL
External Control Terminal
D-sub 9 Pin
RS-232C compatible
PC OUT
R: 0.7 Vp-p (75 Ω)
G: 0.7 Vp-p (75 Ω)
B: 0.7 Vp-p (75 Ω)
HD/VD: 1.0 - 5.0 Vp-p
USB (VIEWER)
TYPE A USB connector
USB (TOUCH)
TYPE B USB connector
DIGITAL LINK / LAN
For RJ45 network and DIGITAL LINK connections, compatible with PJLink™
Communication method: RJ45 100BASE-TX
EXT SP
8 Ω, 20 W [10 W + 10 W] (10 % THD)
Sound
Speakers
120 mm × 40 mm × 2 pcs
Audio Output
20 W [10 W + 10 W] (10 % THD)
Dimensions (W × H × D)
1,868 mm × 1,093 mm × 104 mm / 73.6” × 43.1” × 4.1”
Mass (weight)
approx. 81.0 kg / 178.6 lbs net
8
PREFACE
<80BF1>
SECTION
1
INF-1
CONTENTS
1. Name of each part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-2
1.1. Display body
1.2. Connecting terminals
1.3. Remote controls
1.2. Connecting terminals
1.3. Remote controls
2. Notes on Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-5
2.1. Before service operation
2.2. Service
2.2. Service
3. Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-6
3.1. How to display CAT mode
3.2. Settings and adjustments mode (IIC Mode)
3.3. Software, EEPROM version and failure information (CD Mode)
3.4. Network connection check mode (NW Mode)
3.5. Status display mode (SD Mode)
3.6. Market select setting mode (MS Mode)
3.2. Settings and adjustments mode (IIC Mode)
3.3. Software, EEPROM version and failure information (CD Mode)
3.4. Network connection check mode (NW Mode)
3.5. Status display mode (SD Mode)
3.6. Market select setting mode (MS Mode)
4. Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-13
4.1. Self check of signal system
4.2. Self check of power system
4.3. Diagnosis of the image
4.4. Dignosis of Touch Panel]
4.5. Diagnosis of the Wi-Fi dongle
4.2. Self check of power system
4.3. Diagnosis of the image
4.4. Dignosis of Touch Panel]
4.5. Diagnosis of the Wi-Fi dongle
SECTION 1 SERVICE INFORMATION
Click on the first or last page to see other TH-80BF1U / TH-80BF1W / TH-80BF1E service manuals if exist.