DOWNLOAD Panasonic TC-29P10N / TC-33P10N Service Manual ↓ Size: 5.33 MB | Pages: 45 in PDF or view online for FREE

- 17 -

Board [L]

6-pole convergence magnet

4-pole convergence magnet

Purity magnet

Purity magnet

Fig. 4

VRS magnet

Purpose:  Adjusting the red, blue, and green electron beams so that they hit

the specified fluorescent substance correctly.

Color bar generator

TV screen (visual observation)

Crosshatch pattern
Red pattern (red single color signal)
Rainbow color pattern

Red

1. Receive a crosshatch pattern and perform simple 

adjustment of the convergence with the convergence 
magnets.

2.  Receive a red pattern (red single color signal).
3.  Slide the deflection yoke to the rear (towards board [L] and 

fix it provisionally when the red vertical bar appears.

4.  Adjust the purity magnets so that the red vertical bar 

comes to the center of the screen. (Fig. 4)

5. Loosen the provisionally fixed deflection yoke, move it to 

the rear, so that the entire screen becomes red, and fix it 
provisionally in that position.
Confirm the single-color condition of the entire screen for 
blue and green.

In case of uneven coloring, repeat the adjustments 3. 
and 4. for the color with the uneven coloring.

6.  Receive a rainbow color bar, and use the TV reception 

channel fine adjustment for a black-and-white image.

   (Or use color pattern generator chroma signal cut.)

7.  Confirm that there is no partial coloring for the entire 

screen.

   If there is partial coloring, remove the color unevenness by 

moving the deflection yoke slightly in forward-backward 
direction.

 

If the color unevenness can not be removed, repeat the 
adjustments 1. to 4.

8.  Tighten the screws fixing the deflection yoke and return  

the TV fine adjustment to the original setting.

(A)

(B)

B

R

Fig. 5

Open

Rotate

(A)

(B)

Purpose: Adjustment of the image color deviation

Color bar generator

TV screen (visual observation)

Crosshatch pattern
Red pattern (red single color signal)
Rainbow color pattern

1.  Receive a crosshatch pattern.
2.  Gradually open the knobs of the 4-pole convergence 

magnets and match the red and blue vertical lines at the 
center of the screen.
Next, rotate the entire 4-pole magnets to match the red and 
blue horizontal lines. (Fig. 5)

4-pole convergence magnets

Match red and blue

& !"

- 18 -

G

R,B

R,B

(D)

G

(C)

Fig. 6

Open

Rotate

(C)

(D)

6-pole convergence magnets

Match red and blue to green

Fig. 7

XV

YHC

YV

Picture tube board (L)

Deflectioin yoke

Fig. 8

YHC

Fig. 9

YV

Fig. 10

XV

• 

Caution items

Tilt adjustment with tilting the deflection yoke in up-down or left-right direction is not performed for this unit. 
Please do nottry to do this. Perform YV adjustment for left-right tilt adjustment and YHC adjustment for up-down 
adjustment.
As the XV adjustment core can crack easily, use a nonmetallic screwdriver for the adjustment.

4. Adjust YHC, YV, and XV on the deflection yoke (Fig. 7) so that the 

overall convergence becomes good. (Fig. 8, 9, 10)

When the convergence at the screen center is off, repeat the 

adjustment from item 2.

3. Gradually open the knobs of the 6-pole convergence magnets and 

match the red and blue vertical lines at the center of the screen.
(At this time, red and blue will move practically at the same time.)
Next, rotate the entire 6-pole magnets to match the red and blue 
horizontal lines to green. (Fig. 6)

5. After the adjustment, apply paint lock to the magnets.
6. When the position without deviation of the three colors has been determined, insert wedges between the deflection 

yoke and the picture tube as shown (Fig. 11 below) to fix the deflection yoke.

1

3

2

4

Fig. 11

Wedge insertion positions

Insert the DY wedges 
at the possible 

.

Wedge

Adhesive

Separator paper

' !"

- 19 -

•

For this adjustment, receive a crosshatch pattern, check whether adjustment is required or not, and then adjust.
This unit is equipped with a “16:9 mode” which identifies the input from S-video input and switches automatically to 16:9 screen
size for the full mode (squeeze signal) from a video camera or DVD. (Surface broadcasts remain “4:3”.)
16:9 mode also requires adjustment. Please perform adjustment on the following basis.
The adjustment procedure is the same as for 4:3 mode.

Adjustment

4:3

16:9

1.  V-HET (vertical amplitude)

[3F]

[3F]

2.  V-LIN (vertical lilnearity)

2

3. V-SCR (vertical S-shape compensation)

2

4.  V-POS (vertical position)

5.  H-WID (horizontal amplitude)

6.  H-POS (horizontal position)

1

7.  H-PIN (vertical pin level)

Adjustment

Screen mode

4:3

16:9

8.  H-KEY (vertical pin keystone distortion)

9.  H-TPN (top pincushion)

2

3.

  H-BPN (bottom pincushion)

10. V-EHT (vertical amplitude compensation)

11. H-EHT (horizontal amplitude compensation)

12. V-BKU (top vertical blanking)

13. V-BKD (bottom vertical blanking)

Screen mode

1 Set to the 4:3 adjustment value.
2 Confirm and adjust if required.

 Adjust with 16:9.

•

Rear terminal board

Flyback transformer

Focus 2 (F2)
(Horizontal line adjustment)

Focus 1 (F1)
(Vertical line adjustment)

Screen (SC)

S551
H. CENT
(horizontal center)

Coupler D4

R464
V. SIZE
(vertical amplitude)

R712
H. SIZE. FB
(horizontal amplitude)

Digital tester

Coupler D2, pin 

 +, pin 

 -

Adjustment location Rester completely black

1. Set the item video in the menu [

] (Function setting) to 

] (OFF). (Completely black screen)

2. Connect the pin 

 of the coupler D2 with the      side of the digital 

tester, and connect the pin 

 with the      side.

3. Turn R712 (amplitude FB) on the board [D] and adjust to 

4.0V 

 0.1V.

4. Set the item video in the menu [

] (Function setting) to 

] (ON).

 !"

- 20 -

Color pattern generator

Meassuring location TV screen (visual observation)

Adjustment location Remote control buttons [VOL +/-]

Crosshatch pattern

A

B

A=B

A

B

A=B=5.5 lines

A=B=C

A

B

C

Purpose: Adjustment of amplitude and linearity of the image in vertical direction.

Image adjustment

Standard

Image menu

Image 4 (dynamic)

Adjustment conditions

Vertical position adjustment
1. Set the item [H-V 

] (H-V adjustment) (omitted in the following) to 

[V-HET].

2. Adjust with the remote control buttons [VOL +/-] to a narrower 

vertical amplitude and confirm the vertical center of the image 
(crosshatch pattern).

3. Set to the item [V-POS].
4. Adjust with the remote control buttons [VOL +/-] so that the vertical 

center of the crosshatch pattern comes to the center of the screen.

Vertical amplitude adjustment
5. Set to the item [V-HET], set to "3F", and adjust by turning R464 so 

that the number of horizontal lines of the crosshatch pattern 
becomes 5.5 lines at the top and at the bottom.

Vertical linearity adjustment
6. Set to the item [V-LIN].
7. Adjust with the remote control buttons [VOL +/-] so that the interval 

between the lines of the upper half and the lower half of the 
crosshatch pattern becomes uniform.

Vertical S-shape compensation adjustment
8.

Set to the item [V-SCR].

9.

Adjust with the remote control buttons [VOL +/-] so that the grid 

size of the crosshatch pattern becomes the same at the center and 
at the top and the bottom.

10. Perform the adjustments 6. to 9. alternately until the line interval 

between the straight lines becomes uniform.

• 

Caution items

For adjustment of V-HET, keep "3F" fixed and adjust by turning 
R464. However, when adjustment of the vertical amplitude with 
R464 is not possible, adjust the value for [V-HET] in the range 
from 3A to 44 (hexadecimal).

 !"