DOWNLOAD Panasonic TC-21PM30RQ Service Manual ↓ Size: 33 MB | Pages: 30 in PDF or view online for FREE

Model
TC-21PM30RQ
Pages
30
Size
33 MB
Type
PDF
Document
Service Manual
Brand
Device
TV
File
tc-21pm30rq.pdf
Date

Panasonic TC-21PM30RQ Service Manual ▷ View online

2.5. Adjustment Procedure
Item / Preparation
Adjustment Procedure
+B Voltage
Confirm the DC voltage at the indicated test points, as follows :
1. Operate the TV set.
TPA 12 : 140.5 ± 1.5V
2. Set control as follows :
TPA 11 : 8 ± 1V
Brightness ...........minimum
TPA 10 : 5 ± 1V
Contrast .............. minimum
TPA 21 : 215 ± 15V
RF AGC
1. Receive a colour bar signal at an RF level of 74+1-
2 dBU with 75
loaded.
1. Select “RF AGC” indication in CHK2, on Screen by remote control at factory
mode.
2. Connect digital multimeter to RF AGC at Tuner.
2. Set RF AGC by using remote control Volume (+) or Volume (-) button until voltage
AGC at Tuner reaches 2.6 ± 0.1V at TPA 15 (Tuner point).
3. Increase RF signal strength by 2dB, confirm AGC at Tuner voltage drop.
High Voltage
1. Receive the crosshatch pattern.
1. Connect a DC voltage meter to TPA 20 and confirm the +B voltage is 140.5 ±
1.5V.
2. Set to 0 Beam.
Screen VR .......... minimum
2. Connect a high frequency voltmeter to heater and confirm that voltage reads 6.0
± 0.24 (VRMS).
Contrast .............. minimum
3. Normalize the brightness and contrast.
Item / Preparation
Adjustment Procedure
NTSC TINT COLOUR
Connect a short jumper between TPA 10 and TPA
20.
Press Main Menu and set system to use AV-NTSC
(3.58 MHz).
DYNAMIC ................. Normal
Channel CLR Set ..... STD
1. Adjust Sub-Tint so that No. 2, 3 and 4 becomes level waveform is similar to Fig.
3.
2. Confirm phase at Tint is changes more than ± 30 by Tint control.
3. Confirm that colour level is maximum when colour DAC is adjusted to maximum
position.
Note: Use remote control only when adjusting user mode to Sub-Tint.
Fig. 3
7
TC-21PM30RQ
2.7. Adjustment
2.6. PAL Colour
 1. Receive the PAL B/G studio colour bar pattern and adjust local frequency at the best tuned position.
 2. Pic Menu: Dynamic Normal, Confirm Contrast - 63, Sub Contrast - 21.
 3. Channel colour set --------- STD.
 4. “CHK2” and press digit key “5” (AKB OFF) also confirm OSD become blue colour.
 5. Connect TPA 10 to TPA 20.
 6. Set (A) to 2.3 ± 0.2V by BRT (CHK2) at measurement point TPL 2 Fig. 4.
 1. Connect oscilloscope probe to TPL 2 (G OUT) with 10k
series resistor and adjust Contrast so that (B) as in Fig. 4 is 2.6 ± 0.1V.
 2. Adjust “Sub Colour” so that waveform as in Fig. 4 (1) 2.5 ± 0.1V.
 3. Connect oscilloscope probe to TPL 1 (R OUT) with 10k
series resistor and confirm waveform as in Fig. 5 is (2) 2.7 ± 0.4V.
 4. Take out jumper TPA 10 and TPA 20.
 5. Press digit key “5” (AKB ON) and confirm the OSD become white colour.
8
TC-21PM30RQ
Colour Purity
 1. Set the Brightness and Contrast controls to their maximum
positions.
 2. Operate the TV set for 60 minutes.
 3. Fully degausse the picture tube by using an external
degaussing coil.
 4. Apply a crosshatch pattern signal and adjust the static
convergence magnets to the approximately correct position.
 5. Receive a black and white signal.
 6. Set the control as follows:
Red................minimum
Green.............minimum
Blue.................minimum
Press the Shipping button on the remote control twice to
select CRT Adjustment Mode to select low light.
 7. Loosen the clamp screw for the Deflection Yoke A in Fig. 10
and move the Deflection Yoke as close to the purity magnet
as possible.
 8. Adjust the purity magnetic rings so that a vertical green field
is obtained at the centre of the screen.
Fig. 6
 9. Slowly push the Deflection Yoke and set it where a uniform
green field is obtained.
Fig. 7
 10. Re-adjust the Low Light controls to their correct settings
and make sure that a uniform white field is obtained.
 11. Tighten the clamp screw A in Fig. 10.
Convergence
 1. Apply a crosshatch pattern signal and Normalize Contrast
control to the maximum positions.
 2. Adjust Brightness until the grey position of the crosshatch
pattern just becomes black.
 3. Adjust the Red and Blue line at the centre of the screen by
rotating the R-B static.
Fig. 8
 4. Adjust Red and Blue with Green line at centre of the screen
by rotating (RB)-G static convergence magnetic rings.
 5. Lock convergence magnets with silicone sealer.
 6. Remove the DY wedges and slightly tilt the Deflection Yoke
vertically and horizontally to obtain the good overall
convergence.
Fig. 9
 7. Fix the Deflection Yoke by reinserting the DY wedges. Refer
to Fig. 10.
 8. If purity error is found, repeat “Colour Purity” adjustment.
Before Colour Purity, Convergence and White Balance adjustment are attempted,
V. Height, H. Centre and Focus adjustments must be completed.
9
TC-21PM30RQ
2.8. Adjustment of CRT VRS
2.8.1. Preparation
a. Set DY to CRT not to tilt up an down left and right deflection.
b. Set CY to CRT and set CY magnet primarily (Fig. 1.).
Purity magnet: Set purity magnet that 2 magnet are (TOP POSITION)
VRS magnet: Set VRS magnet 2 magnet are (HORIZONTAL POSITION)
2.8.2. Adjustment
a. Receive that Cross Hatch pattern.
b. Adjust V-SHIFT-50Hz.
c. Set 2 magnet of horizontal position to up and down eually so that center part of CRT (Fig. 2.)
10
TC-21PM30RQ
Page of 30
Display

Click on the first or last page to see other TC-21PM30RQ service manuals if exist.