Panasonic TC-21GX10TS Service Manual ▷ View online
2 Service Hints
2.1. Service Position for E-Board
1. Remove the back cover.
2. Stand the TV set as shown in Fig. 2.
3. Remove the A-Board from the TV set by pulling the main board out as shown in Figure 2.
Fig. 2
2.2. Factory Mode Adjustment
1. Adjustment.
a. Set Timer ON (30 minutes)
Press remote’s RECALL & panel’s vol down key simultaneously to select service mode.
b. CHK should appear on right side of TV screen.
After few seconds CHK 1 should appear on right side of TV screen.
NOTE :
To move from CHK 1 to CHK 2 mode, etc, please follow below rotation:-
c.
CHK 1
Press digit key “4” to move option mode forward.
Press digit key “3” to move option backward.
The function rotation will be as follows :-
5
TC-21GX10TS
d. After selecting the required option mode press Vol up / Vol down to adjust correct option. OSD will change to RED colour.
Press digit “0” to memorize data.
e. CHK2
Press digit key “2” to move forward to CHK2.
The function rotation will be as follows:-
f.
Press digit key “4” to move forward from Colour ------> Sub-Colour, etc.
Press digit key “3” to move backward from Sub-Colour ------> Colour, etc.
g. Press volume up / volume down to adjust setting.
h. Press digit key “5” to make the AKB OFF (Blue OSD) - first time.
Press digit key “5” to make the AKB On (White OSD) - second time.
i.
CHK3
Press digit key “2” to move forward to CHK 3.
The function rotation will be as follows:-
6
TC-21GX10TS
j.
Press digit key “4” to move forward from V-SLOPE ------> V-SHIFT
Press digit key “3” to move backward from V-SHIFT ------> V-SLOPE
k.
Press volume up / volume down to adjust required setting.
l.
CHK4
Press digit key “2” to move forward to CHK 4.
The function rotation will be as follows:-
m. Press digit key “4” to move forward from R-CUT ------> G-CUT
Press digit key “3” to move backward from G-CUT ------> R-CUT
n. After selecting the required mode, press volume up / volume down to adjust required setting.
o. Press digit key “5” to make the AKB OFF and H-Line mode - first time.
Press digit key “5” to make the AKB ON and Normal picture - second time.
p. After finish adjustment, press Power ON / OFF button on remote control to go to normal TV mode.
2. HOW TO CHANGE CHANNEL BY I2C BUS CONTROLLER
a. Short FA1 and FA2
b. Select Slave address ‘70H’, Sub-address ‘43H’ for RF AGC.
* Example :
Slave Address = 70H’, Sub-Address = 43H’
Data = 80H’ = Center
7
TC-21GX10TS
2.3. Adjustment for White Balance
Preparation:
1. Receive the white balance pattern and aging should have been performed over 30 minutes.
2. Set the picture menu to DYNAMIC NORMAL.
3. Degausse the CRT face.
4. Fix the CRT colour analyzer receiver unit to CRT face.
Adjustment of Low Light.
1. Adjustment Sub Bright, so that Y = 6.3 ± 1.0 nit.
2. Adjustment R-CUT OFF, so that X = 0.285 ± 0.015 nit.
3. Adjustment G-CUT OFF, so that Y = 0.300 ± 0.015 nit.
Adjustment of High Light
1. Adjustment Sub Bright, so that Y = 150 nit.
2. Adjustment R-Drive, so that X = 0.275 ± 0.010 nit.
3. Adjustment G-Drive, so that Y = 0.275 ± 0.010 nit.
2.4. Adjustment for CRT CUT OFF
Preparation:
1. Connect the oscilloscope probe to TPL5.
2. Screen VR min.
3. Set the data Sub Bright, Bright.
4. In service Mode at “Bright” dac press [6] in factory mode to enter vertical line and adjust by volume down or up button.
5. Adjust “Screen VR” until 1-H Line appears.
8
TC-21GX10TS
Click on the first or last page to see other TC-21GX10TS service manuals if exist.