DOWNLOAD Panasonic TC-21FG10TSU-CIS Service Manual ↓ Size: 4.59 MB | Pages: 29 in PDF or view online for FREE

Model
TC-21FG10TSU-CIS
Pages
29
Size
4.59 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / GP41 CHASSIS
File
tc-21fg10tsu-cis.pdf
Date

Panasonic TC-21FG10TSU-CIS Service Manual ▷ View online

Power Source :
AC SINGLE 220-240V, 50/60 Hz
Power Consumption :
67W
Aerial Impedance :
75
unbalanced
Coaxial type
Receiving System :
17 Systems
Receiving Channels :
VHF
2-12 PAL / SECAM B,K1
0-12 PAL B (N ZEALAND)
1-9 PAL B (N ZEALAND)
1-12 PAL / SECAM D
1-12 NTSC M (JAPAN)
2-13 NTSC M (U.S.A)
UHF
21-69 PAL G,H,I / SECAM G.K.KI
28-69 PAL B (Australia)
13-57 PAL D,K
13-62 NTSC M (JAPAN)
14-69 NTSC M (U.S.A)
CATV
S1-S20 (OSCAR)
1-125 (U.S.A CATV)
C13-C49 (JAPAN)
S21-S41 (HYPER)
Z1-Z37 (CHINA)
TC-21FG10TSU-CIS
GP41 Chassis
5A,9A (AUSTRALIA)
Audio Terminal :
AV
Video In 1 Vp-p 75
Audio In Approx. 0.5V, 47k
Monitor Out
Video Out 1 Vp-p 75
Audio Out Approx. 0.5V, 1k
High Voltage :
27.5kV ±1.5
at zero beam current
Picture Tube :
A51LYZ295X
50.5cm (21 inches)
Measured diagony,
90° deflection
Audio Output :
7.0W
Dimensions :
Height : 473 mm
Width : 648 mm
Depth : 488 mm
Mass :
23 kg (Net Wt.)
Specifications are subject to change without notice.
Mass and dimensions shown are approximate.
Colour Television
Specifications
ORDER NO. MTV0601451CE
 1 Safety Precautions 
3
 1.1. 
General Guide Lines 
3
 1.2. 
Leakage Current Cold Check 
3
 1.3. 
Leakage Current Hot Check (Fig. 1) 
3
 1.4. 
X-Radiation 
3
 1.5. 
GP41 Chassis Block Diagram 
4
 2 Service Hints 
5
 2.1. 
Service Position for E-Board 
5
 2.2. 
Factory Mode Adjustment 
5
 2.3. 
Adjustment for White Balance 
7
 2.4. 
Adjustment for CRT CUT OFF 
7
 2.5. 
Adjustment Procedure 
8
 2.6. 
Adjustment 
9
 3 Conductor Views 
12
 4 Schematic Diagram 
13
 4.1. 
A Board 
15
 4.2. 
L Board 
20
 5 Parts Locations 
23
 6 Replacement Parts List 
24
 6.1. 
Replacement Parts List 
25
CONTENTS
 Page 
Page
2
TC-21FG10TSU-CIS
1 Safety Precautions
1.1. General Guide Lines
 1. It is advisable to insert an isolation transformer in the AC supply before servicing this hot chassis.
 2. When servicing, observe the original lead dress, especially the lead dress in the high voltage circuits. If a short circuit is found,
replace all parts which have been overheated or damaged by the short circuit.
 3. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers, shields and isolation R-C
combinations, are properly installed.
 4. When the receiver is not to be used for a long period of time, unplug the power cord from the AC cord outlet.
 5. Potential, as high as 29.0kV is present when this receiver is in operation. Operation of the receiver without the rear cover
involves the danger of a shock hazard from the receiver power supply. Servicing should not be attempted by anyone who is not
thoroughly familiar with the precautions necessary when working on high voltage equipment. Always discharge the anode of the
picture tube to the receiver chassis before handling the tube. After servicing make the following leakage current checks to
prevent the customer from being exposed to shock hazards.
1.2. Leakage Current Cold Check
 1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
 2. Turn on the receiver’s power switch.
Measure the resistance value, with an ohmmeter, between the jumper AC plug and each exposed metallic cabinet part on the
receiver, such as screw heads, aerials, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 4 M
and 20 M
. When the exposed metal does not have a return path to the chassis,
the reading must be infinite.
1.3. Leakage Current Hot Check (Fig. 1)
 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
 2. Check a 2 k
non-inductive resistor and an AC/DC current meter, in series with each exposed metallic part on the receiver in
turn and an earth such as a water pipe.
The current from any point should not exceed 0.7 mA peak AC or 2 mA DC. In the case of a measurement being outside of
these limits specified, there is a possibility of a shock hazard and the receiver should be repaired and rechecked before it is
returned to the customer.
Fig. 1
1.4. X-Radiation
Warning:
The potential sources of X-Radiation in TV set are the EHT section and the picture tube. When using a picture tube test jig for
service, ensure that jig is capable of handling 29.0kV without causing X-Radiation.
Note: It is important to use an accurate periodically calibrated high voltage meter.
 1. Set the brightness to minimum.
 2. Use the remocon to get into Service Mode.
 3. Measure the EHT. The meter reading should indicate 27.5±1.5kV. If the meter indication is out of tolerance, immediate service
and correction is required to prevent the possibility of premature component failure.
 4. To prevent the possibility X-Radiation, it is essential to use the specified picture tube, if service replacement becomes
necessary.
3
TC-21FG10TSU-CIS
1.5.
 GP41
Chassis
Block
Diagram
GP41 CHASSIS BLOCK DIAGRAM
CRT
defl.
coil
CRT
DRIVE
VM DRIVE
L
FRONT INPUTS
AV2  : V/L/R
MAIN
POWER
SWITCH
G
GEOMAGNETIC
WOOFER
AMP
IC2401
PVP
IC1801
R/G/B
SCL
SDA
CVBS IN
REAR INPUTS
AV1  : V/L/R
AV 3 : YUV/V/L/R 
VCT-IF
IC601
V_IN
CVBS OUT
MON_OUT
R
G
B
R/G/B
MON_OUT
V/L/R
EEPROM
IC1101
VM
SCL SDA
A_IN
IF
H
A
AUDIO
OUT
V
SPEAKER
AUDIO
AMP
IC2301
V OUT
H OUT
TUNER
FRONT INPUTS
AV2  : V/L/R
PP
 29" models
                     PIP models
4
TC-
21FG1
0TSU-
CIS
Page of 29
Display

Panasonic TC-21FG10TSU-CIS Service Manual ▷ Download

  • DOWNLOAD Panasonic TC-21FG10TSU-CIS Service Manual ↓ Size: 4.59 MB | Pages: 29 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Panasonic TC-21FG10TSU-CIS in PDF for free, which will help you to disassemble, recover, fix and repair Panasonic TC-21FG10TSU-CIS TV. Information contained in Panasonic TC-21FG10TSU-CIS Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.