Panasonic E3 / E3D / Chassis Service Manual / Other ▷ View online
5
PINNO.
SYMBOL
IN/OUT
FUNCTION
1
RM_IN
I
REMOCON SIGNAL FROM THE INFRA-RED-RECEIVER IS INPUT
2
SDA1
I/O
IIC SERIAL DATA LINE H: NORMAL L: IIC COMMUNICATING
3
SCL1
O
IIC SERILAL CLOCK LINE H: NORMAL L: IIC COMMUNICATING
4
SYNC1
I
SYNC FOR MAIN PICTURE H: NO SYNC
5
AFC1
I
AFC VOLTAGE (0-5V/6STEPS)FOR TUNER1 INPUT
6
AFC2
I
AFC VOLTAGE (0-5V/6STEPS)FOR TUNER2 INPUT
7
PROTECT
I
PROTECT ON/OFF SW. VOLTAGE INPUT ON: 1.1-5.0 V OFF: 0 - 1.1V
8
---
---
---
9
RM_IN
I
REMOCON SIGNAL FROM THE INFRA-RED-RECEIVER IS INPUT
10
KEY_IN
I
KEY-IN VOLTAGE IS INPUT FROM THE USER’S CONTROL PANEL(O-5V)
11
FAN_IN
I
THE VOLTAGE COMES FROM THERMISTOR
12
LED
O
LED IS LIGHT H: POWER ON L: STAND BY
13
M_SOUND_DEF
O
MONITOR SOUND MUTE ON :H NORMAL :L
14
RF_AGC1
O
RF AGC1 VOLTAGE OUTPUT (0-5V/128 STEPS) IS OUTPUT
15
---
---
---
16
SIF1
O
4.5MHZ : L 5.5MHZ : L 6.0MHZ : H 6.5MHZ : H
17
SIF2
O
4.5MHZ : L 5.5MHZ : H 6.0MHZ : L 6.5MHZ : H
18
DAF_SW
O
DURING POP MODE,NTSC SYS VOL (0-5V/128 STEPS) IS OUTPUT
19
VIDEO _GAIN
O
SUB CONTRAST CONTROL FOR MAIN PICTURE
20
VCR/GAME
O
VCR MODE ON :L NORMAL : H
21
SOUND_DEF_AMP
O
SOUND MUTING VOLTAGE IS OUTPUT MUTE ON : H NORMAL:L
22
VDD
-
+5V IS APPLIED
23
---
---
---
24
---
---
---
25
---
---
---
26
CVBS_IN
I
COMPOSIT VIDEO SIGNAL INPUT
27
RELAY
O
POWER ON : L POWER OFF : H
28
SRQ
I
FOR FACTORY USE FACTORY : <2.5V NORMAL : >2.6V
29
SOUND_DEF_MIN
O
SOUND MUTING VOLTAGE IS OUTPUT MUTE ON : H NORMAL:L
30
CONVER_IN
I
H: NORMAL L: RMCON NOT ARROW
31
BEAM_SW
O
BEAM_SW H: POP, 100HZ, 16:9, TEXT L: OTHERS
32
SDA3
I/O
IIC SERIAL DATA LINE H: NORMAL L: IIC COMMUNICATING
33
SCL3
O
IIC SERILAL CLOCK LINE H: NORMAL L: IIC COMMUNICATING
34
SEARCH&SYNC
O
SERCH & WITHOUT SYNC : H OTHER :L
35
SOUND_AI
I
SOUND AI (MUSIC DET. WHEN SOUND MENU IS AUTO)
36
---
---
---
37
---
---
---
38
VSS
-
GROUND
39
H_SYNC_IN
I
HORIZONTAL SYNC SIGNAL INPUT FOR ON SCREEN DISPLAY
40
RESET_DEV.
O
DEVICE RESET H: NORMAL L: RESET
41
YS
O
MASK SIGNAL FOR ON SCREEN DISPLAY
42
R
O
RED SIGANL FOR ON SCREEN IS OUTPUT SIGNAL : H
43
G
O
GREEN SIGANL FOR ON SCREEN IS OUTPUT SIGNAL : H
44
B
O
BLUE SIGANL FOR ON SCREEN IS OUTPUT SIGNAL : H
45
COMP
I
DAC FOR ON SCREEN DISPLAY
46
IREF
I
DAC FOR ON SCREEN DISPLAY
47
VREF
I
DAC FOR ON SCREEN DISPLAY
48
FAN OUT
O
FAN ON : H OFF : L
49
AVDD
-
ANALOG VDD. +5V IS APPLIED
50
PD0
O
OUT PUT SIGNAL OF INTERNAL PHASE CORRECTION
51
VCOI
I
INPUT SIGNAL OF INTERNAL VCO
52
TEST
-
TERMINAL FOR TEST
53
GAME_STATE
I
GAME : L OTHERS : H
54
RESET
I
NORMAL : H RESET : L
55
V_SYNC_IN
I
VERTICAL SYNC SIGNAL INPUT FOR ON SCREEN DISPLAY
56
RESET_ENABEL
I
RESET ENABLE : H DISABLE : L
57
5V_DET
I
+ 5V DETECTOR H: 5V ON
58
TV/TEXT
O
DURING TEXT MODE : H NORMAL : L
59
SDA2
I/O
IIC SERIAL DATA LINE H: NORMAL L: IIC COMMUNICATING
60
SCL2
O
IIC SERILAL CLOCK LINE H: NORMAL L: IIC COMMUNICATING
61
VDD
-
+ 5V INPUT
62
OSC1
I
4MHZ CLOCK OSCILLATION TERMINAL
63
OSC2
O
4MHZ CLOCK OSCILLATION TERMINAL
64
VSS
-
GROUND
6
FUNCTION
PART NO.
REF.NO.
MPU
MN102L35GTR1
IC1101
Memory
TVJ292
IC1102
Teletext
SDA5450C70GE
IC3504
Tuner(MAIN)
ENV5954J6(1ST)
TNR001
Tuner(SUB)
ENVG29503G(2ND)
TNR002
Stereo
MSP3415
IC2001
Video processor
CXA2069Q
IC3001
CIP
VCP3215C(MAIN)
IC1301
CIP
VCP3211A(SUB)
IC1302
Multi Window
MB87F1720
IC1306
100Hz
SDA9255(V PROSESSOR)
IC1307
DFU
FJB007
IC1308
Display processor
TDA9332H
IC1309
Sound control
BH3866S
IC2401
Expander DAC
CXA1315M
IC1001
Conver DAC
JLC1562BF
IC7103
Deflection
AN5491K
IC411
Expander DAC(deflection)
CXA1315P
IC435
Expander DAC(WB1)
CXA1315P
IC7707
Expander DAC(WB2)
CXA1315P
IC7702
Block Diagram
<**> ->board name
IC13
08
<DG>
DFU
DFU
IC2001
<B2>
Stereo
IC10
01
<A>
SUB
DAC
SUB
DAC
IC2401
<A>
SOUND
IC1301
<DG>
VIDEO
PROC.
(MAIN)
PROC.
(MAIN)
IC13
01
<DG>
V.P.
IC3001
<H>
AV SW
<H>
AV SW
TNR002
<A>
TUNER
Sub
IC1309
<DG>
Display Processor
TNR001
<A>
TUNER
Main
IC1302
<DG>
Video Processor
(SUB)
IC1306
<DG>
CIP
IC411
<F>
DEFLE
<F>
DEFLE
CTION
IC435
<F>
DAC
IC71
03
DAC
IC77
07
DAC1
IC7106
<DC>
CONV.
MPU
<DC>
CONV.
MPU
RMT
Stop
Stop
PORT
FAN
PORT
AD IN
IC7705
<DC>
Single
ABL
EEPROM
IIC3
IIC1
IIC2
IC77
02
DAC2
02
DAC2
IC350
4
<T>
TEXT
IC3502
<T>
EPROM
IC1101
MPU
MPU
IC1304
<DG>
M.W
7
2.
Single ABL
Purpose :
In a normal TV the ABL operation detects the current
following to the secondary coil of the fly-back transformer
and controls the contrast. In a video projection TV,
however, the current for the secondary coil of the fly-back
transformer is measured as the total current for the three
projection tube. Therefore the current can not be controlled
even if most of the electron beams are sent though one
projection tube. For this reason the monochrome ABL
circuit detects the maximum current for each projection tube
and controls the same. We have added a circuit which
accelerates the ABL operation time, and lowers the
contrast.
In a normal TV the ABL operation detects the current
following to the secondary coil of the fly-back transformer
and controls the contrast. In a video projection TV,
however, the current for the secondary coil of the fly-back
transformer is measured as the total current for the three
projection tube. Therefore the current can not be controlled
even if most of the electron beams are sent though one
projection tube. For this reason the monochrome ABL
circuit detects the maximum current for each projection tube
and controls the same. We have added a circuit which
accelerates the ABL operation time, and lowers the
contrast.
Operation :
In normal ABL operation detects the current flowing to FBT
which supplies the high voltage to the three projection
tubes, as with a standard TV. This is alike MD2 chassis.
The current flowing to each projection tube is detected in
the colour output transistor emitter, and the maximum
current to each projection tube is then input to the Q7735
through D3352,D3362 and D3372.
In normal ABL operation detects the current flowing to FBT
which supplies the high voltage to the three projection
tubes, as with a standard TV. This is alike MD2 chassis.
The current flowing to each projection tube is detected in
the colour output transistor emitter, and the maximum
current to each projection tube is then input to the Q7735
through D3352,D3362 and D3372.
Then output value of Q7735 is input to pin No. 5,7,9 and 11
of IC7705, these are compared with pin No. 4,6,8 and 10 of
IC7705.
Compared result is output from pin No..1,2,13 and 14 as
P0, P1, P2 and P3. P0-P3 data are input to IC7702, then
CRT current following is separated to 5 levels/ Ranks in the
IC7702 as follows.
of IC7705, these are compared with pin No. 4,6,8 and 10 of
IC7705.
Compared result is output from pin No..1,2,13 and 14 as
P0, P1, P2 and P3. P0-P3 data are input to IC7702, then
CRT current following is separated to 5 levels/ Ranks in the
IC7702 as follows.
P0
P1
P2
P3
RANK
LEVEL
H
H
H
H
A
Danger
H
H
H
L
B
I
H
H
L
L
C
I
H
L
L
L
D
I
L
L
L
L
E
Safety
Detection data is input to MPU through IIC bus line and
MPU controls the contrast to keep detection level safety.
MPU controls the contrast to keep detection level safety.
R,G,B OUT
Q7735
D3352,D3362,D3372
CRT-Anode
FBT
T554
Q9601
4
5
7
6
8
9
11
10
2
1
13
14
+5v
IC7705
M5234P
M5234P
IC7702
CX1315P
CX1315P
10
9
2
1
14
15
59
60
IC1101
MPU
MPU
IC1309
Display Processor
Display Processor
43
11
10
BCL
SDA
SCL
+
-
+
-
+
-
+
-
E10 A10
16
1
P3
P2
P1
P0
LG1/W3
8
IIC bus
Q3351
Q3361
Q3371
AB
8
3.
Shading
Purpose :
To correct variations in the left and right shading due to
differences in the positions of the projection tubes, to
correct gamma and to blank the final sweep interval.
To correct variations in the left and right shading due to
differences in the positions of the projection tubes, to
correct gamma and to blank the final sweep interval.
Shading Correction :
Horizontal parabola wave is made by horizontal plus via
Q7741-Q7744 and Q7745-7747. H.SAW wave and
Horizontal parabola wave is made by horizontal plus via
Q7741-Q7744 and Q7745-7747. H.SAW wave and
H.PARA wave is input to Pin No. 2 and 5 of IC7704, then
they are mixed in the IC7704 and then it is output from pin
No. 7 o IC7704.
The correction wave-form output from IC7704 is input to
pins 10 and 8 of IC7703, the R and B gain is adjusted, and
then the left and right brightness are varied to correct any
lack of colour uniformity on the screen.
they are mixed in the IC7704 and then it is output from pin
No. 7 o IC7704.
The correction wave-form output from IC7704 is input to
pins 10 and 8 of IC7703, the R and B gain is adjusted, and
then the left and right brightness are varied to correct any
lack of colour uniformity on the screen.
4.
Prevention of projection tube burn-out
Purpose :
This feature operates to prevent burn-out from occurring in
the phosphor substance of the projection tube when the
picture is stopped for an extended period.
This feature operates to prevent burn-out from occurring in
the phosphor substance of the projection tube when the
picture is stopped for an extended period.
Operation :
Each time the power is turned off, the channel is changed,
or AV input switching is performed, the screen display
position is moved and rotated horizontally and vertically
approximately 3 mm in a clockwise direction.
The MPU sends a command to move the screen display
position horizontally and vertically, to IC1309, through the
I²C Bus, for an input from the button on the TV, or from the
remote control, to turn the power on or off, or change the
channel, or switch the AV input.
Each time the power is turned off, the channel is changed,
or AV input switching is performed, the screen display
position is moved and rotated horizontally and vertically
approximately 3 mm in a clockwise direction.
The MPU sends a command to move the screen display
position horizontally and vertically, to IC1309, through the
I²C Bus, for an input from the button on the TV, or from the
remote control, to turn the power on or off, or change the
channel, or switch the AV input.
A3
W2
7
IC7704
AN6142
AN6142
H.SAW
Q7741
|
Q7744
HP-BLK
H.PARA
Q7745
|
Q7747
ADJ.
2
Q7748
7
5
10
8
19
18
20
IC7703
PA0057A
PA0057A
R-gain
B-gain
TPW101
TPW117
6
TPW2
+12V
R-out
G-out
B-out
(H.V)
(H+1.V)
(H.V+1)
(H+1.V+1)
Click on the first or last page to see other E3 / E3D / Chassis service manuals if exist.