Panasonic KX-TS2368CAW Service Manual ▷ View online
5
KX-TS2368CAW
2.2.1.
Suggested PbF Solder
There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s
specific instructions for the melting points of their products and any precautions for using their product with other materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3 mm, 0.6 mm and 1.0 mm.
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s
specific instructions for the melting points of their products and any precautions for using their product with other materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3 mm, 0.6 mm and 1.0 mm.
2.3.
Discarding of P.C. Board
When discarding P. C. Board, delete all personal information such as telephone directory and caller list or scrap P. C. Board.
0.3 mm X 100 g
0.6 mm X 100 g
1.0 mm X 100 g
6
KX-TS2368CAW
3 Specifications
Note:
• Design and specifications are subject to change without notice.
Power Source:
Redial:
Speaker:
Speaker:
Microphone
Input Jack:
Input Jack:
:
Dimensions (H x
W x D):
Weight:
Operating Environment:
:
Dial Mode:
F
From 3 AA (LR6, R6, UM-3) batteries
From 3 AA (LR6, R6, UM-3) batteries
rom telephone line
Last dialed telephone number
Handset; 3 cm (1 ) PM dynamic type, 150
Handset; 3 cm (1 ) PM dynamic type, 150
Elect
Telephone Line, Data port
Telephone Line, Data port
ret condenser microphone
Appr
ox. 95 mm x 167 mm x 224 mm
Approx. 730
5
o
C - 40
o
C
Tone (DTMF)/Pulse
g
7
KX-TS2368CAW
4 Technical Descriptions
4.1.
Block Diagram
Mic
Speaker
VDD
ST
OP
Head Set
LCD
IC801
IC601
Q421, Q424
CPU
Handset
AMP
Receiving
T
ransmit
AMP
Dial
Line Selector SW
Q108
AMP
Q109
LINE1
Hold
LINE2
Hold
Q405, Q406
T21
Q101, Q103
Ringer
D21
D1
10
IC201
IC22
Handset
AMP
Sending
DC-DC
Converter
T
one
Detection
Mic
Speaker
Mic
Speaker
H/S
T
LINE1
C21
R21
T1
Ringer
D1
IC1
C1
R1
R
D1
1
1
Q501~505
Q551~555
LINE1 LED
LINE2 LED
T
LINE2
R
SP-PHONE
AMP
IC303
Q302
CPU
Reset
IC304
3.7V
IC302
4.5V
Battery
Battery
Low
CPU
Key Board
Switch
KX-TS2368 BLOCK DIAGRAM
8
KX-TS2368CAW
4.2.
Circuit Operation
4.2.1.
Ringer Circuit
When the bell signal is input between telephone line, the signal are output at the speaker via the following path:
Tel line
R1 [R21] C1 [C21] D1 [D21] IC1 (1) [IC22 (1)] IC1 (8) [IC22 (8)] C5 [C35] T1 [T21] C625 Speaker
[ ] : in case of Line2
4.2.2.
Telephone Line Interface
4.2.2.1.
Circuit Operation
• On hook
Q101 is open, Q101 is connected as to cut DC loop current and cut the voice signal.
• Off hook (in case of Line 1)
In talk status, RLY output from IC801 (45) changes to low level, causing Q103, Q101 to turn on and resulting in a line loop.
Q101 turns on thus providing an off-hook condition (active DC current flow through the circuit) and the following signal flow is
for the DC loop current.
(Line 1) Tip
Q101 turns on thus providing an off-hook condition (active DC current flow through the circuit) and the following signal flow is
for the DC loop current.
(Line 1) Tip
POS101 D110 SW110 Q101 Q108 R124 D106 D110 (Line 1) Ring
• Pulse mode
A pulse signal that repeated switches between high and low logic is output from IC801 (44).
This switches the line loop on and off, generating the dial pulse signal.
This switches the line loop on and off, generating the dial pulse signal.
• The receiving signal flows: (in case of Line 1)
TEL line
POS101 SW110 Q101 C113 R125 C108 Q109 Q405 Q406 C414 VR402 CN401
CN402
Speaker (H/S)
• The transmission signal flows: (in case of Line 1)
Mic
VR401 Q421 Q424 C435 R437 Q108 SW110 POS101 Tel Line
4.2.3.
Tone Detect
This circuit is used to sense the status of the line (busy tone or dial tone) during Auto Redial.
4.2.3.1.
Circuit Operation
D110
Q101 C201 R201 R205 IC201 (5) IC201 (1) D202 R208 Q201 IC801 (50)
When the subscriber hangs-up, check the intermittent tone. If cycle tone is detected, the collector of Q201 goes to a low logic.
Click on the first or last page to see other KX-TS2368CAW service manuals if exist.