Panasonic KX-TS2363CAW / KX-TS2363UAW Service Manual ▷ View online
13
KX-TS2363CAW/KX-TS2363UAW
9 Disassembly and Assembly Instructions
Ref. No.
Procedure
Shown in Fig —.
To remove —.
Remove —.
1
1
1
Lower Cabinet
Screws (2.6
×12) . . . . . . . . . . . . . (A)×5
2
1 ~ 2
2
Printed Circuit Board
Remove the P.C.Board
Remove the P.C. Board
Fig 1
Fig 2
A
14
KX-TS2363CAW/KX-TS2363UAW
10 Miscellaneous
10.1. IC Block Diagram
10.1.1. Ringer IC (IC1)
Vcc 1
RSL 2
LFI 3
LFO 4
OUT
8
HFI
7
HFO
6
GND
5
LOW FREQ
OSC
OSC
HIGH FREQ
OSC
OSC
POWER SUPPLY
WITH
HYSTERISIS
AMP
Pin descriptions
1
2
3
4
5
6
7
8
Vcc
RSL
LFI
LFO
GND
HFO
HFI
OUT
Pin No. Pin name
Power supply pin
RSL pin
Low-frequency time
constant connector pin
GND pin
High-frequency time
constant connector pin
Output pin
This is the power supply pin for the lC. It is connected to the ( ) pin of the diode bridge.
This is used to change the operation initiation current when connected to the GND pin.
This is connected to the time constant that determines the oscillation frequency
on the warble.
on the warble.
This pin has the lowest potential on the lC. It is connected to the ( ) pin of the diode bridge.
This is connected to the time constant that determines the oscillation frequency
on the tone side (the audible frequency side).
on the tone side (the audible frequency side).
This is used to connect a piezoelectric buzzer, or to connect a dynamic speaker through a
transformer.
transformer.
Name
Function
15
KX-TS2363CAW/KX-TS2363UAW
10.2. How to Replace the Flat Package IC
Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount), a
soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.
soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.
10.2.1. Preparation
• PbF (: Pb free) Solder
• Soldering Iron
• Soldering Iron
Tip Temperature of 700
°F ± 20 °F (370 °C ± 10 °C)
Note: We recommend a 30 to 40 Watt soldering iron. An expert may be able to use a 60 to 80 Watt iron where someone with
less experience could overheat and damage the PCB foil.
less experience could overheat and damage the PCB foil.
• Flux
Recommended Flux: Specific Gravity
→ 0.82.
Type
→ RMA (lower residue, non-cleaning type)
Note: See About Lead Free Solder (Pbf: Pb free) (P.4)
10.2.2. How to Remove the IC
1. Put plenty of solder on the IC pins so that the pins can be completely covered.
Note:
If the IC pins are not soldered enough, you may give pressure to the P.C. board when cutting the pins with a cutter.
2. Make a few cuts into the joint (between the IC and its pins) first and then cut off the pins thoroughly.
3. While the solder melts, remove it together with the IC pins.
When you attach a new IC to the board, remove all solder left on the board with some tools like a soldering wire. If some solder is
left at the joint on the board, the new IC will not be attached properly.
left at the joint on the board, the new IC will not be attached properly.
16
KX-TS2363CAW/KX-TS2363UAW
10.2.3. How to Install the IC
1. Temporarily fix the FLAT PACKAGE IC, soldering the two marked pins.
*Check the accuracy of the IC setting with the corresponding soldering foil.
2. Apply flux to all pins of the FLAT PACKAGE IC.
3. Solder the pins, sliding the soldering iron in the direction of the arrow.
10.2.4. How to Remove a Solder Bridge
1. Lightly resolder the bridged portion.
2. Remove the remaining solder along the pins using a soldering iron as shown in the figure below.
2. Remove the remaining solder along the pins using a soldering iron as shown in the figure below.
Click on the first or last page to see other KX-TS2363CAW / KX-TS2363UAW service manuals if exist.