Panasonic KX-TS2358UAB / KX-TS2358UAW (serv.man3) Service Manual ▷ View online
4
KX-TS2358UAB/KX-TS2358UAW
1 Safety Precautions
1.1.
For Service Technicians
• Repair service shall be provided in accordance with repair technology information such as service manual so as to pre-
vent fires, injury or electric shock, which can be caused by improper repair work.
1. When repair services are provided, neither the products nor their parts or members shall be remodeled.
2. If a lead wire assembly is supplied as a repair part, the lead wire assembly shall be replaced.
3. FASTON terminals shall be plugged straight in and unplugged straight out.
2. If a lead wire assembly is supplied as a repair part, the lead wire assembly shall be replaced.
3. FASTON terminals shall be plugged straight in and unplugged straight out.
• ICs and LSIs are vulnerable to static electricity.
When repairing, the following precautions will help prevent recurring malfunctions.
1. Cover plastic parts boxes with aluminum foil.
2. Ground the soldering irons.
3. Use a conductive mat on worktable.
4. Do not grasp IC or LSI pins with bare fingers.
2. Ground the soldering irons.
3. Use a conductive mat on worktable.
4. Do not grasp IC or LSI pins with bare fingers.
2 Warning
2.1.
Battery Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's Instructions.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's Instructions.
2.2.
About Lead Free Solder (PbF: Pb free)
Note:
In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that con-
tains lead.
We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin (Sn),
Silver (Ag), and Copper (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.
tains lead.
We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin (Sn),
Silver (Ag), and Copper (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.
Caution
• PbF solder has a melting point that is 50
°F ~70°F (30°C ~ 40°C) higher than Pb solder. Please use a soldering iron with temper-
ature control and adjust it to 700
°F ± 20°F (370°C ± 10°C). In case of using high temperature soldering iron, please be careful
not to heat too long.
• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100
°F (600°C).
• If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible and
be sure that any remaining is melted prior to applying the Pb solder.
• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the
opposite side (See the figure below).
5
KX-TS2358UAB/KX-TS2358UAW
2.2.1.
Suggested PbF Solder
There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s
specific instructions for the melting points of their products and any precautions for using their product with other materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s
specific instructions for the melting points of their products and any precautions for using their product with other materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.
2.3.
Discarding of P.C. Board
When discarding P. C. Board, delete all personal information such as telephone directory and caller list or scrap P. C. Board.
6
KX-TS2358UAB/KX-TS2358UAW
3 Specifications
Note:
• Design and specification are subject to change without notice.
• Specifications are subject to change without notice.
• Specifications are subject to change without notice.
Important:
*: Some functions may not work properly without batteries, Refer to the Operationg Instructions for details.
7
KX-TS2358UAB/KX-TS2358UAW
4 Technical Descriptions
4.1.
Block Diagram
D3
, D5
C1
D
1
PC1
R1
IC
1
D
4
, D
6
H
a
ndset
Q1
0
7
Q1
0
1
, Q1
0
2
, Q1
0
3
D1
0
1
T
T
1
SP
R
MIC
SP-
Phone
IC
6
0
1
SP
D
302
MIC
D3
0
1
IC
3
0
1
IC
3
0
2
4
.5
V
IC
8
5
1
B
a
tte
ry
IC
3
0
3
IC
501,
Q
502
LC
D
KX
-T
S2
3
5
8
:
BL
O
C
K DI
AG
RAM
Q4
0
1
, Q4
0
2
, Q4
0
3
Q
422
IC
801
MI
C
O
N
R
inge
r indic
a
tio
n LE
D
L
E
D
1
(2
AP)
JOHN S
M
IT
H
1234567890
RI
NG
ER
IC
DR
IN
G
Li
ne
ON
/OF
F
H
andse
t
R
e
ce
iv
in
g
Am
p
EEPR
O
M
TIPIN
S
ide
to
ne
Br
id
g
e
RE
SE
T
BA
TT
LO
W
R
e
s
e
t IC
H
a
ndse
t
Se
n
d
in
g
Am
p
Ke
yb
o
a
rd
Sw
it
ch
RIN
GIN
B
a
tte
ry
L
o
w
De
te
c
to
r
Re
g
u
la
to
r
3.
3 V
FSK /
DTM
F Ci
rc
u
it
W
a
ke
up C
ir
c
ui
t
WA
KEUP
RIN
G_D
ET
SP-
Ph
o
n
e
Ci
rc
u
it
(2
AP)